Search Documents

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984

By Peter I. Brooker

The semi-variogram, the basic tool of geostatistical estimation procedures, must itself be estimated from the available data. From a numerically simulated two dimensional deposit, with known variability expressed through its semi-variogram, the standard arithmetic mean estimator is used to calculate experimental semi-variograms. These are determined on a series of data sets obtained from the deposit with various sampling grids which cover different areas of the deposit and which have a wide range of available data. The orders of discrepancies between estimated and theoretical semi-variograms are determined in this idealized situation; and this provides a basis against which to assess experimental semi- variograms made on field data.

Jan 1, 1982

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. It is ap-parent from observing the industrial practice of sulfide mineral flotation over the last decade that progress is being made in optimizing the operating aspects of flotation. Examples of this are the availability of improved instrumentation and related computer control devices, the modification of mechanical flotation cell designs, the introduction of column cells, better reagent dosage control, blending of feed ores, increasing attention to coarse and fine particle separations, the successful introduction of new frother chemistries, etc.

Jan 1, 1989

By W. L. O?Connell

[Patent Issue No. Date Issued To Subject 386,504 July 24, G. Sweanor The separation of quartz from a 1588 metal with a liquid such as CS2 or CHC13 under water by introducing mixture into water layer. Quartz will stay in water layer while metal sinks through organic.]

Jan 1, 1963

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Event cameras are used for their performance in high dynamic-range lighting conditions which are canonical to active mining environments. Direct labeling of event-based image data to train a model to perform semantic segmentation using traditional methods is slow and error-prone. This study proposes a framework to use roughly hand-labeled color images from a mine as an input to an intermediary probabilistic algorithm called alphamatting to generate a ground-truth data set. These high-fidelity labels can be used to train a semantic segmentation model to differentiate the support strap from the roof. This model can then be leveraged to segment an event-based scene to enable autonomous roof bolting. This pipeline has been shown to achieve an accuracy of 88% with a false positive rate of 3%.

Feb 1, 2024

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By R. D. Miller

Application of shallow seismic reflection to problems associated with mineral exploration, mine planning, abandoned-mine detection, and environmental evaluation has been successful in a variety of geologic settings. Increased dynamic range of recording equipment and decreased cost of processing hardware and software have made shallow seismic reflection a cost-effective means of imaging geologic targets significant to mining operations. Seismic data possess sufficient resolution in many areas to detect faulting with displacement of less than 3 m in coal seams as thin as 2 m at depths of 200 m. Subsurface voids associated with abandoned mines at depths of less than 20 m can be detected and mapped. Seismic reflection has been successful mapping disturbed subsurface associated with dissolution mining of salt Complex geologic features associated with deposition of various hydrothermal minerals have been effectively mapped with high resolution seismic reflection at depths from 80 to over 300 m. Faults in sulfur-bearing cap rock over salt domes have been accurately located, allowing improved efficiency of the dissolution mining process. Shallow high-resolution seismic reflection has the potential to significantly enhance the economics and safety of mine operations.

Jan 1, 1993

By Michael Gay

Right in the heart of Boston Harbor lies Deer Island, where a ten-year, 6 billion dollar sewage treatment plant is under construction. The 9.5 mile long, 25.5' diameter Effluent Outfall Tunnel is the center piece of this program. A Robbins double-shielded TBM is currently driving this challenging tunnel some 400 feet below sea level. This paper will discuss the set-up and operation of this Tunnel Boring Machine in driving the longest single heading tunnel ever built in North America.

Jan 1, 1993

By Seppo] [Kreula

Outokumpu Oy has acquired considerable experience with on-stream X-ray fluorescence analyzers and with computer control of flotation processes over several years. It became evident at the outset of this work that a reliable and accurate on-stream analyzer was more than a collection of different pieces of hardware linked together. Extensive work was done to develop an integral analyzer system, beginning with process samples through the spectrometer to report typewriters, recorders and the control computer. To date, over ten Courier-300 analyzer systems based on this development have been installed world-wide, several of which provide the key information for successful computer control systems. Computer control of flotation processes has been under development at the Pyhäsalmi concentrator since 1968. Two different control strategies have been implemented. The copper flotation is controlled by means of a mathematical model and economic criteria, whereas the "evolutionary operation principle" is applied to the zinc flotation. The computer control system installed at' the Vuonos-mine has been developed according to the same guidelines. In order to consolidate this wide experience, a flotation computer control system, Proscon-100, was developed by Outokumpu Oy, and the first system was installed at Kotalahti in 1972. In addition to the technological experience, enough information has also been gathered to illustrate the economical, benefits accruing through the use of these advanced tools of automation.

Jan 1, 1973

By Faruk Oksuz, Dave Schiemann, Miguel Sanchez, Patrick Jensen

"The McCook Main Tunnel connects Chicago’s Tunnel and Reservoir Plan (TARP) Mainstream Tunnel to the McCook Reservoir. The tunnel system consists of a 10 m (33 ft) finished diameter and 490-m (1,600-ft) long hard-rock tunnel constructed from a 27.5-m (90-ft) diameter and 92 m (300 ft) deep main gate shaft. The gate shaft houses six high-head 4.4 x 9 m (14.5 x 29.5 ft) wheel gates installed in the bifurcated and steel-lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir. Construction of the McCook Main Tunnel in live flow conditions was a challenging task for the McCook Main Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch and contractor Kiewit Infrastructure Co. (Kiewit). Once completed in two stages in 2017 and 2029, the McCook Reservoir will hold 38 billion L (10 billion gal) of combined sewer overflows (CSO) and flood waters from the city of Chicago and 36 surrounding communities in Cook County, IL The construction of the tunnel system was divided into two contracts. The first contract for the gate and construction access shaft was completed in August 2011. The second contract included tunnel excavation and concrete and steel lining that was completed in September 2014; installation of gates and hydraulic cylinders that was completed in June 2017; and the last major construction activity was the removal of a temporary concrete plug (bulkhead) and lining that tunnel section to bring the overall tunnel and gates system online before Dec. 31, 2017.This article focuses on the installation, testing and commissioning of the high head wheel gates. Live tunnel connection details to TARP Mainstream Tunnel were addressed in a previous paper submitted at the World Tunneling Conference in 2016."

Mar 1, 2019

By Harry Perry

Although the markets for coal in the United States have changed rapidly over the last three decades, the uses of coal, namely, to produce heat and power or coke have been left almost unchanged. The coke is used either as a chemical reducing agent alone or as a reducing agent and source of heat. Most of the heat and power markets for coal require no coal processing, although for more than 50 years, many proposals to skim the more valuable substances in coal before burning have been advanced. Thus, the only large tonnage market requiring processing of coal is high-temperature carbonization to make coke. At present, coal requires processing for some small markets, but for future potential large markets, such as gasification, conversion to liquid and gaseous fuels, and conversion to chemicals, coals will require more processing than is now being done.

Jan 1, 1962

"There’s no fast way to add more than four miles of track, most of it underground, to the Sound Transit Link Light Rail system in the Seattle area. But increasingly busy traffic through a number of neighborhoods made it necessary. That’s the challenge a joint venture of several tunneling contractors faced when starting its portion of the $1.9 billion Northgate Link Extension in 2013, and the project is still keeping them busy three years later. Completion will mean just a 14-minute ride from Northgate to downtown for an extra 60,000 passengers by 2030. The transit lines will join 58 km (36 miles) of new and under-construction light rail lines running north, east and south from Seattle.Voters, tired of long commute times, approved the project, a key part of Seattle’s regional mass transit system, in 2008. The extension is part of a plan adopted by the Sound Transit board in 1996 to connect the region’s major activity centers. The Northgate project is meant to relieve one of the area’s most congested traffic areas by connecting the Northgate, Roosevelt and University District neighborhoods to existing routes including downtown Seattle and SeaTac airport.Sound Transit dedicated more than a quarter of the project’s estimated expense — $440 million -— to general contractor JCM Northlink LLC to handle the tunnel segment. JCM is a joint venture formed in 2013 between Jay Dee Contractors of Livonia, MI, Frank Coluccio Construction of Seattle, WA and Michels Corp. of Brownsville, WI. The contractors regularly collaborate on large-scale projects and brought experience working on a different section of the extension they completed in 2013.JCM project leaders knew immediately that the schedule would be demanding. They had to work around the clock, six days a week to meet deadlines. The extension runs through highly populated areas, meaning contractors had to follow strict city noise restrictions between 10 p.m. and 7 a.m. Plus, supervisors needed to manage the scheduling of nearly 250 employees to keep work running smoothly.“We had eight different operations and four different subcontractors trying to work in one tunnel,” said Chris Wood, JCM site project superintendent. “It’s important that we keep work linear. That’s the biggest challenge: keeping a path in and out so you can pour concrete, keep electricians and carpenters going, and accomplish everything else.”"

Jan 6, 2018

"There is no fast way to add more than 6.4 km (4 miles) of track, most of it underground, to the Sound Transit Link Light Rail system in the Seattle, WA area. But increasingly busy traffic through a number of neighborhoods made it necessary. That’s the challenge a joint venture of several tunneling contractors faced when starting its portion of the $1.9-billion Northgate Link Extension in 2013, and the project is still keeping it busy three years later. Completion will mean just a 14-minute ride from Northgate to downtown for an extra 60,000 passengers by 2030. The transit lines will join 57 km (36 miles) of new and under-construction light rail lines running north, east and south from Seattle.Voters tired of long commute times approved the project, a key part of Seattle’s regional mass transit system, in 2008. The extension is part of a plan adopted by the Sound Transit board in 1996 to connect the region’s major activity centers. The Northgate project is meant to relieve one of the area’s most congested traffic areas by connecting the Northgate, Roosevelt and University District neighborhoods to existing routes including downtown Seattle and SeaTac airport.Sound Transit dedicated more than a quarter of the project’s estimated expense — $440 million -— to general contractor JCM Northlink LLC to handle the tunnel segment. JCM is a joint venture formed in 2013 between Jay Dee Contractors of Livonia, MI, Frank Coluccio Construction of Seattle, WA and Michels Corp. of Brownsville, WI. The contractors regularly collaborate on large-scale projects and brought experience working on a different section of the extension they completed in 2013.JCM project leaders knew immediately that the schedule would be demanding. They had to work around the clock six days a week to meet deadlines. The extension runs through highly populated areas, meaning contractors had to follow strict city noise restrictions between 10 p.m. and 7 a.m. Plus, supervisors needed to manage the scheduling of nearly 250 employees to keep work running smoothly.“We had eight different operations and four different subcontractors trying to work in one tunnel,” said Chris Wood, JCM site project superintendent. “It’s important that we keep work linear. That’s the biggest challenge: keeping a path in and out so you can pour concrete, keep electricians and carpenters going, and accomplish everything else.”"

Dec 1, 2016

By A. Juganda, H. PINHEIRO, J. Brune, N. SANDOVAL, G. Bogin, K. Gallagher, F Wilson

The present work discusses the nuances of scaling and flow similarity to develop a 1/40th scale version of a longwall coal mine. Details on the geometric, kinematic, and dynamic scaling of the physical model are presented and discussed. This works also discusses using a 30% CO2 – 70% He gas mixture as a surrogate for methane. It also presents the implications of various Reynolds numbers (ranging from 7,000 to 140,000) and rotation of the shearer drums in the dynamic representation of the airflow and gas mixtures in the physical scaled model.

Mar 19, 2022

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022