Search Documents

By W. Lin

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Jan 1, 1997

By Robert L. Marovelli

Organizational development that attempts to simultaneously deal both with training and with job design parameters as they relate to mine health and safety, productivity, and quality of life is one of several areas of research that the Bureau of Mines is pursuing. The Bureau sees potential in this particular effort for reducing accidents and injuries, improving worker satisfaction and health, and increasing productivity.

Jan 1, 1981

By Kenneth W. Torpey, James G. Ball, Richard F. Flanagan, David S. McAllister

INTRODUCTION Under a Federal grant by the Urban Mass Transit Administration (UMTA) (80%), and sponsored by the State of New York (200), Niagara Frontier Transportation Authority is constructing a 10.3 km (6.4 mile) light rail rapid transit system in Buffalo, New York. The $450 million project, which began construction in the Spring of 1979, is unique in rail transit alignment designs in the U.S.A. and the first predominantly underground light rail system in North America. The Buffalo project is unique in that the first phase of the expandable system follows the alignment of Main Street and is on the surface in a proposed 1.6 km (1.0 mile) pedestrian mall in the downtown business district. The alignment then progresses northward into a cut-and-cover portal and standard double-box configuration for 2.74 km (1.7 miles) at a depth of 9.1-10.7 m (30-35 ft) and subsequently drops into bedrock at depths of 18.3-27.4 m (60 to 90 ft). The 5.63 km (3.5 mile) rock tunnel section consists of two single tunnels 4.88 m (16.0 ft) nominal finished diam. and includes five stations. The rock tunnel line section was divided into a north and south contract of 2 316 m (7,600 ft) and 3 243 m (10,640 ft), respectively. Due to the existing surface facilities and the future station locations, the line tunnel contracts differed considerably in their shaft access

Jan 1, 1981

I reached New York at the start of my second South American adventure on Jan. 9, 1916. In the Anaconda office I found that we were not to take the steamer for two weeks which gave me time to study reports on Potrerillos and Corocoro. Reno Sales, whom I had met in Butte only casually, was to go with us to South America. Though he was only a little older than I, he was already an unquestioned leader of our profession, and we became and remained good friends. William Braden was in New York and would return to Santiago with us. Tom Hamilton would also be returning from a vacation. Leighton Stewart, a young engineer who was to work for Braden, was going on the steamer with us, taking along his wife. And of course Dr. Ricketts would go along. He had just become engaged to John Greenway's half sister, Kate Greenway, and in order not to be away from her longer than was necessary, he did not reach New York until a day before we sailed. This made eight of us who would be in the party. We were to go to Corocoro first, as Braden had taken an option on the Chilean company there. Development was already under way. As reports came in by mail we tried to get as good an idea of the property as we could before the actual examination. Mr. Thayer "put us up" at India House, one of the best lunch clubs in New York, and Reno and I ate our lunches there almost every day. Thayer, Braden, and Cornelius Kelley, who was to succeed Mr. Ryan as president of Anaconda, joined us when they could. At the lunches they told us about the under- ground war in Butte a few years earlier. When I wrote my chapter on the Butte wars in Romantic Copper more than 15 years later I could not help being biased a bit by my friends, all of whom were on the Anaconda side. But their opponents in the Clark and Heinze camp were just as biased in their comments on my book.

Jan 1, 1976

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By D. R. Spears

The Bureau of Mines has investigated the fundamental aspects of shear-flocculation using a rapid, in-situ particle size analyzer. Silica was stirred in the presence of an aliphatic amine to determine the effects of collector coverage, stirring speed, and solids concentration on the kinetics of shear-flocculation. The results showed that shear-flocculation is a two-stage process. In the first stage, mean particle size increased rapidly in the first 1-2 min of reaction; in the second stage, an equilibrium was set up between the rate of floc growth and floc decay. Collector dosage affected the position of the equilibrium by altering the number of surface sites for particle-particle attachment. A minimum stirring speed was necessary for shear-flocculation to occur and was dependent on solids concentration and collector dosage. This speed was the minimum necessary for particles to overcome the electrostatic energy barrier which kept conditioned particles dispersed. Larger particles flocculated more rapidly. At very high stirring speeds, large flocs became unstable, resulting in a narrowed particle size distribution in the slurry.

Jan 1, 1993

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By Shawn T. Sorrell

Phillips Coal Company (PCC) submitted the first surface mine permit application under the Office of Surface &lining approved regulatory program of the State of Louisiana. This application for the Oxbow Lignite Surface Mine which is located approximately 64 kilometers (40 miles) southeast of Shreveport, Louisiana was submitted in March 1981. The State of Louisiana Office of Conservation, Surface Mining Division, assigned this application number LSM-1, indicating it is the first one submitted in Louisiana history. The permit area for the Oxbow Mine encompasses 6,251 hectares (15,627 acres). Of this total permit area, 5,862 hectares (14,656 acres) were classified by soil type as prime farmland by the U.S. Soil Conservation Service (SCS). Prime farmland acreage in the permit area became a major central issue in our early planning stages and throughout the permitting process of the Oxbow Mine, due to the magnitude of acreage involved.

Jan 1, 1982

By D. A. Bird

Water chemistry data were used to identify the sources of ground-water and surface-water inflow to the IOZ block cave mine. Water samples were collected to obtain vertical and lateral hydrochemical profiles within different levels of the underground workings. Water chemistry data were evaluated in conjunction with geologic and structural information to define controls on locations of ground-water inflows, and to select targets for drilling and interception of water. Drilling has intercepted water-producing zones that were previously unidentified through mapping and drilling. The program has resulted in a reduction in water inflows to the block cave area.

Jan 1, 1998

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By W. L. Hollinshead

For more effective and cost saving production in tunnels, the machinery used on construction sites will be equipped with guidance systems combined with working procedure management systems. This paper describes sensors for these systems and various system configurations. A project is described which uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 1999

By Edward S. Plotkin, Joseph D. Guertin

In a continuing effort to upgrade tunnel design and construction practice, the New York City Transit Authority sponsored a geotechnical monitoring program on a recently completed section of the E. 63rd Street line in mid-town Manhattan. The purpose of the program was to document rock behavior as well as temporary and final rock support systems to provide a possible basis for either confirmation or modificification to design methods and construction specifications. This paper describes those portions of the study associated with rock behavior and temporary support systems. The entire study included monitoring of rock movements above the tunnel as well as adjacent to a 36.6m (120 ft) shaft, monitoring of stresses in steel ribs, monitoring of loads in rock bolts in two test sections and monitoring of stresses in the final concrete lining. PROJECT DESCRIPTION Route 131-A, Section 4 is located in mid-town Manhattan extending from under the Central-Park Zoo on Fifth Avenue eastward under 63rd Street to the end of contract between Madison and Park Avenue. Figure 1 is a Project Locus Map. The contract included approximately 355m (1165 l.f.) of 4 track tunnel(13.4m (44 ft) wide by 13.7m (45 ft) high excavated dimensions) plus a 22.9m (75 ft) by 19.8m (65 ft) by 36.6m (120 ft) deep ventilation shaft. The entire tunnel and most of the excavation shaft was excavated in metamorphic rock, known locally as the Manhattan Schist. The depth to tunnel invert varied from approximately 27.4m (90 ft) at the west end of the contract to 35.Om (115 ft) at the east end. Rock cover above the excavated crown varied from approximately 6.7m (22 ft) at the approximate mid-point of the contract to 18.9m (62 ft) at the western end. A plan view and interpreted geologic profile are illus-

Jan 1, 1979

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By K. N. Mayfield, T. Novak

"The applications for automation continue to expand within the mining industry. These applications can range from the startup, control, and shutdown of processing plants to the autonomous operation of surface haulage trucks. However, the term “automation” should not necessarily be interpreted as the total elimination of human interventions since numerous mining processes can be partially automated. The future survivability of many mining operations will be influenced by a company’s willingness and ability to understand, accept, and utilize this technology. The mining workforce, including management and engineering, should be familiar with the technological capabilities and limitations for effectively implementing automation into mines for improving safety and productivity. The Department of Mining Engineering at the University of Kentucky has recognized this educational gap and developed an automation laboratory, along with project-oriented courses at the undergraduate and graduate levels. The laboratory and the course objectives are described in this paper, as well as the skills and abilities that students obtain at the completion of the course(s). BACKGROUND The touted benefits of automation include: improved productivity, lower operating costs, reduced drudgery of repetitive operations performed by workers, and the removal of workers from hazardous locations. The acceptance of advanced technology by the mining industry, however, has traditionally been slow. This cautious approach is understandable considering the complex and harsh conditions routinely encountered in mining operations. Bad experiences with some premature installations of newly hyped technologies may have also resulted in lingering skepticism by many mine operators. Nonetheless, with thoroughly demonstrated reliability and proven applications, automation based on programmable logic controllers (PLCs) has made significant inroads into the mining industry. Programmable logic controllers (PLCs) are the workhorses of automation. They were originally conceived in the late 1960s, long before the invention of the personal computer (PC). Initial PLC applications were directed towards sequential relay control in manufacturing plants, which subsequently eliminated the use of “relay logic” that was based on hard-wired electromechanical relays. With continuous advancements in electronics and computer technology over the years, PLCs have evolved into sophisticated and powerful devices with very stable operating systems. They are designed for deterministic logic execution with extreme consistency in timing, along with a high tolerance to temperature, humidity, and vibration (Smith 2003). Because of their robust characteristics, PLC networks now provide the backbone for most industrial automation applications."

Jan 1, 2017

By J. M. Applegate

In the same way that a blueprint communicates information about a structure, a useful systems architecture should provide information that guides the construction and implementation of computing systems. Taking the blueprint analogy a step further, a plot plan can also show where in the "bigger picture" a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: 1. The primary purpose of computer based systems relative to particular task or operation. 2. The relationship of systems to each other and an indication of their interaction and dependencies. 3. The relationship of systems relative to the organization and its objectives. 4. Indications of where IS/IT resources can best be allocated to support the organization. 5. The overall context in which new systems and technologies can be assessed for both their impact on current system and on the organization itself.

Jan 1, 1998

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By J. Mastoris

The problem of defining the optimum final limits of an open pit mine has challenged the mining industry for the last three decades, mainly due to the great number of variables involved and the sheer computational effort required in real life applications. An actual lignite deposit is used in this study in order to introduce and apply a methodology to be used as a basis for surface mine design optimization. A geologic reserves model of the deposit is first developed with the use of an integrated geostatistical modeling package. The model is transformed into an economic one through the use of flexible objective function formulation(s). The optimization of the final open pit limits is then enabled with the use of a competent, commercial optimizer, and comparative sensitivity analyses are performed in order to study the effect of some basic mining and economic parameters on the optimal pit design. The conclusions drawn can develop useful guidelines for decision making by the mine operator.

Jan 1, 1995

By Ian Sheppard, Kugan Kuganathan

The Mount Isa Rocky Paste Fill (RPF) was one of the five fill options investigated for the Enterprise Mine filling between June 1996 and September 1996. Co-disposal of deslimed cemented tailings (CHF) and suitably graded rockfill (RF) in certain ratios produced the rocky paste fill. The RPF behaved like a cohesive paste with very high proportion of rockfill in the mix. Several large-scale mixing trials and drop tests proved that the rocky pastefill results in a homogeneous fill mass after placement. Segregation of RF was a common problem with MIM's traditional cemented rock fill (CRF), which is a combination of CHF and RF. The segregation was eliminated and a non-segregating paste like fill was created by optimising the particle size distribution of RF, and combining the RF and the CHF in optimum ratios. In rocky pastefill, the excess water in the cemented deslimed tailings slurry is taken up by the rockfill as the surface moisture on the rockfill particles and also as pore water between the particles. This results in thickening of the CHF, and the resultant mix is a non-segregating cohesive paste, which can easily spread to any horizontal distance inside a stope at a very low surface angle. The rocky pastefill releases no free water and relatively more pervious than the standard CHF due to rockfill component. With an average cement addition of 1.5 to 2% the rocky pastefill can develop higher strengths over 1Mpa. The rocky paste fill is applicable in many situations and can accommodate a variety of coarser materials that would be available in different mine sites. This paper present the research work and the experience associated with the rocky paste fill, and gives clear design principles for any potential users.

Jan 1, 2001

By G. Rainville, I. Servi, F. Katrak

Despite the severe drought conditions that reduced farm requirements for industrial mineral products, most industrial minerals markets in 1988 continued their growth or, at worst, remained flat. Earlier projections of output declines did not materialize in most segments. Preliminary estimates of demand in Europe and Asia show strong growth for most industrial minerals. Profitability in industrial minerals in North America was best in those minerals that had a significant export market or were not strongly regional. Growth and price trends in the more regional industrial minerals markets in the US such as sand and gravel, crushed stone, and cement, more closely followed the broadly disparate regional economic conditions. For example, sand and gravel and crushed stone grew strongly in the Pacific Coast and northeastern markets but not as much as in the Southeast. Total growth for sand and gravel in 1988 is projected at about 3% above 1987 levels. Combined production is up about 27 Mt (30 million st) to 2 Gt (2.2 billion st). Following the relentless trend of foreign acquisition of US cement companies (currently about two-thirds are owned by foreign interests), several aggregate operations have been purchased by foreign companies. Notable among these in 1988 was the acquisition of Rinker Materials Corp. by CSR of Australia. The acquisition of this Florida-based aggregate and concrete operation will expand the current holdings of CSR in the southeastern US, with operations consolidated under the Rinker logo. In addition, Pike Industries of New England and J.L. Shiely Co. of Minnesota were significant aggregate producers that were acquired by foreign firms. New England's only cement manufacturer, Dragon Products, was acquired by a subsidiary of Cementes del Norte of Spain. Dravo continued to expand its influence in the lime and limestone markets. It became the major supplier of construction aggregates on the inland river system with its purchase of Cyprus Minerals' limestone aggregate operations in Kentucky, Louisiana, and Texas. Although lime production continued to grow from 14 to 15 Mt (15.7 to 16.7 million st) in 1988, lime imports decreased for the fifth consecutive year to 145 kt (160,000 st). In the more export-oriented industrial minerals markets, performance was generally very good for 1988. Soda ash enjoyed an excellent year, with its price up to $102.50/t ($93 per st). This reflected the tight market situation for soda ash, particularly in late 1988. Soda ash production in 1988 was 8.6 Mt (9.5 million st), reflecting the industry's improved efficiency. Particularly significant was the increase in caustic soda prices that led to increased substitution by soda ash. The export market remained at 2.1 Mt (2.3 million st). Phosphate production recovered to the 42 Mt (46 million st) level, a 12% increase despite a soft export market. The price, however, remained soft throughout the year. W.R. Grace sold its interest in its Florida phosphate mine and its phosphoric acid complex as part of its divestiture of the agrichemicals business. The strengthening of the major producers has continued as lower cost capacity has been idled. Future permitting of phosphoric acid facilities and development of reserves will be necessary to maintain current production levels beyond the mid- to late 1990s. Despite new developments worldwide in the titanium minerals market, strong demand has continued to apply pressure to price, with concentrate and slag prices going up. The demand for high quality slag as feedstock for pigment production has resulted in process improvements in South Africa (Richard's Bay) and in plans by Canada to import high quality ilmenite by 1991 to produce a 90% TiO2 slag. Although growth in industrial silica sand applications was small in 1988, concentration in the industry continued. Unimin continued to acquire silica operations. Unimin is now the nation's leading producer of granular silica. The end users of silica have consolidated further. Owens-Illinois purchased Brockway Inc., a leading container glass producer. Three companies now control 75% of the container glass industry. ECC continued to be an aggressive purchaser of industrial minerals operations throughout the world. It acquired Cyprus Minerals' calcium carbonate business as well as two operations in Italy. In addition, ECC continued its aggressive acquisition of kaolin (Australia) and aggregate producers. 1988 was a good year for industrial minerals markets worldwide. More importantly, though, it was a year that showed continuing consolidations of reserve ownership in the industry around the world. Barite AN. Castelli, Baroid Drilling Fluids Inc. US mine production of barite decreased 9.4% during 1988. Consumption (sold or used by grinding plants) increased by 37.9%. Imports are estimated to have increased by 21.2%. World mine production decreased by 9.8%, according to the US Bureau of Mines. The value of domestically produced barite, fob mine, decreased 4.6%, according to the Bureau. The declared value cif US port of all imported ground barite during the first 10 months of 1988 increased from $37.16/t ($33.71 per st) in 1987 to $37.92/t ($34.40 per st), according to Bureau figures. Nevada continued to be the leading producer of barite with 72% of the total, followed by Georgia and Missouri. The Bureau of Mines estimates 69% of US mine production was used as a weighting agent in drilling fluids. The other 31% was used in barium chemicals, glass, or as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. Of the total consumption used by grinding plants and chemical manufac-

Jan 1, 1989