Search Documents

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By Vincent A. Scovazzo

During the winter months of late 1985 and early 1986, residents along Dry Fork near Grundy, Virginia (United States) experienced seismic events that they attributed to longwall mining at Island Creek Corporation’s (Island Creek) Virginia Pocahontas Mine No. 3 (VP-3 mine). Island Creek contacted STS D’Appolonia Ltd. (STSDL) on March 7, 1986, to investigate these events. An STSDL representative, Vincent Scovazzo, interviewed residents of Dry Fork on March 10, 1986. It was noted that only people within a residential structure felt the events they described as house shaking, vibrating walls, and ceramics falling from shelves. STSDL representative installed a blast monitor at a residence. Within 2 days, various events were recorded. Some could be attributed to truck and heavy equipment movement. Eight events had no obvious cause but appeared on resident’s written logs as earthquakes caused by mining. STSDL contacted Utah Geophysical, Inc. who had developed a technique to determine the mode of rock failure using the seismic record. Utah Geophysical was engaged to install and monitor a microseismic network, locate the epicenter of the events, and work with STSDL in determining modes of failure. The network was comprised of six geophones located at five stations. Data was recorded for 24 days from May 20 through June 13, 1986. The data was filtered to eliminate events determined to have an origin other than the longwall panels’ overburden and under-burden. The larger events from this filtered data set were selected and analyzed to determine their hypocenter locations, time of occurrence, magnitudes, and failure mode. Processed data was interpreted, tabulated, and plotted by STSDL to provide information relative to the sources of the seismic vibrations and their possible relationship to the mining operation.

Jul 1, 2023

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By Sergio Flores, Nate Long, William Hodder, Phil Rhodes, Tim McQueary

The Surface Water Supply Project Segment B3 is a 4 miles section of tunnel that will run East- West in Houston TX, from Hopper St to I-45. The tunnel will be mined by using a 128" Dia refurbished 1987 Lovat Tunnel Boring Machine capable of operating in Open or EPB mode. The tunnel will be temporarily supported with ribs and lagging and a 96" Dia pipe will be grouted into place. All four miles of this project are within Petroleum Pipeline Easements. The project includes seven shafts, 2000' of tunnel in potentially petroleum contaminated ground, crossing the Hardy Toll d, I-45, the nion Pacic ailroad ight of Way and multiple oil and gas pipeline crossings. This paper summarizes the planning and drive performed to date.

Jun 23, 2024

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Thomas E. Finch

Coal produced from surface mines in the Western United States is becoming a more important part of this nation's economy as other types of fuels become scarce. This paper reports the investigation of alternative methods of handling the parting between two coal seams. The results of this investigation are presented as the engineering-economic aspects of alternative parting handling methods involving stowing or back filling techniques. The coal and parting characteristics were selected as being representative of those under consideration or actively mined in the West. The basic philosophy of evaluation is to establish a mine-within-a-mine where equipment selected for minimal capital investment can remove the parting and second seam nearly independent of the ongoing, present production. With proper consideration of design, this parting-coal removal is evaluated as a second operation within the first and has its own profitability measure. The Fort Union Area of Montana, Wyoming, and the Dakotas contains large reserves of low sulfur sub-bituminous coal. In many locations, several coal seams are close to the surface and are separated by relatively thin layers of parting. The removal of overburden and the mining of the upper seam is accomplished effectively with conventional mining methods and equipment. Mining a second seam of coal and handling the parting in accord with economic and environmental controls presents a number of problems. Typically, mining companies have adapted the conventional strip mining techniques used in the East. However, the extreme thickness of the western coal seams offers alternative mining method possibilities for parting and second seam removal.

Jan 1, 1976

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By T. N. Moore, E. M. De Souza

J. Dasher Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to allow editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels. Reply by T. Moore We have read the discussion of our paper by Mr. Dasher. Our reaction is one of surprise and incredulity. It would seem that Mr. Dasher takes exception to the use of the decibel scale to present vibration acceleration data, and the use of hertz as the unit for frequency. The basis for his objection to the decibel appears to be that it has no dimensions (which somehow invalidates its use), that it is "non-metric" and, finally, that it is parochial (of limited or narrow scope). His objection to the use of the term hertz is not stated, but we will assume that it stands condemned as "non-metric" and parochial. Obviously we disagree with Mr. Dasher's views and will now outline our reasons. Although the decibel scale originates from transmission line theory and telephone engineering, it is also at present widely used, not only in the fields of electronic engineering and acoustics, but also in the area of vibration. The original definition of the decibel (dB) was based on power ratios: dB = 10 log 10(W/W0) where Wo is a reference power. However, as the power measured across a given impedance is related to the square of the force acting upon this impedance, Z, a more commonly used definition is: [2 dB = 10 logF /Z) = 20 log F/F 10\ F0 2 /Z(0)] where F and F0 are the r.m.s. values of the forces. Now, if the measurements are related to one and the same impedance, the decibel notation in the form of 20log10(X/Xo) may be used as a convenient relative magnitude scale for a variety of quantities. Thus, X may, for instance, be an r.m.s. displacement, velocity or acceleration. It is only required that XD always be a reference quantity of the same type as X. That is, when X represents an acceleration, then X0 represents a reference acceleration. This is the formulation used in our paper. This was not an arbitrary choice on our behalf but reflects standard practice as specified in the International Standard ISO 5349-1986(E) Mechanical Vibration - Guidelines for the Measurement and the Assessment of Human Despite the metric prefix, the decibel is a parochial expression of (l) the logarithmic ratio of the loudness of a sound to what is normally audible or (2) the logarithmic ratio of two power signals in radio or electronics. A decibel is not a unit, much less an SI, unit and has nothing whatsoever to do with the acceleration of drill handles. Stating that m/s2 (acceleration) is decibels is without reason. Whoever reviewed this material should not have allowed publication of figures of dB and H.[ ] Exposure to Hand-Transmitted Vibration. This was clearly stated in the "measurement protocol" section of our paper. This quantity is then referred to as the acceleration level and is expressed in dB. We may have inadvertently caused some confusion when we simply used the term acceleration to refer to acceleration level on our diagrams. At the time, we felt the use of dB or m/s2 would make the context clear to the reader. For any confusion this decision may have engendered, we apologize. Since the decibel expresses the ratio of two like quantities, it certainly has no dimensions. It is, however, common practice to treat "decibel" as a unit as, for example, in the sentence, "The acceleration level measured at the operator's hand was 160 dB." The expression of measured quantities in dimensionless form is not inherently unacceptable. In fact, in many areas of engineering it is standard practice (consider the use of Reynolds Number, Nusselt Number, etc.). The fact that the decibel is a dimensionless quantity makes the question of whether it is a SI unit nonsensical. However, it is valid to insist that the dimensional quantities used to obtain the decibel values be expressed in SI units. A careful reading of our paper will make it clear that the measured acceleration was, in fact, expressed in units of m/s2 as was the reference acceleration (l x 10-6 m/S2). These are the accepted derived SI units for acceleration. See, for example, the standard ASTM E380-89a Standard Practice for Use of the International System of Units (SI) (The Modernized Metric System). Concerning Mr. Dasher's implication that hertz (Hz) is an unacceptable unit of measure for frequency, we would again refer him to the standard ASTM E380-89a. Here, he will find (section 2.4.2) that hertz is an accepted "special name" for the derived SI units-1. This is in keeping with numerous other international standards including ISO 5349-1986(E) to which we referred in our paper. In conclusion, we agree with Mr. Dasher on the desirability of expressing measurements in modern SI units. But we would remind him that the standards that define the use of these units, and the accepted means of presenting measured data, are in a continual state of refinement. It is, therefore, incumbent upon him to keep abreast of these changes if he wishes to constructively critique the work of others.[ ]

Jan 1, 1992

By D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore, and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement, and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risk, the effectiveness of caps and covers, and provide information to aid in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs), and lysimeters. Many of the monitoring devices can be linked to a datalogger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1997

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of both underground and surface operations. The East Ertsberg Skarn System (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production is from the third lift (Deep Ore Zone), which is scheduled to peak at 80,000 mtpd during 2009, with this rate sustained through 2015. The orebody is proven below the existing caving level, with the next vertical block called the Deep Mill Level Zone (DMLZ). This paper presents an overview of the DMLZ Mine based on recent feasibility level study. The mine is being designed for a peak production rate of 29.2 million mtpy, with 1,803 total ore draw points spread over a panel caving footprint of about 1.3km by 375m. The present reserves for this mine total 501 million tonnes. Located 1,400-1,800m below the original surface, the DMLZ will be one of the deepest caving operations in the world. Production is scheduled to commence in 2015. Discussion is provided on most design aspects including; caving methodology and layouts, geotechnical predictions and risks, ore handling systems, ventilation design and associated infrastructure, high-lift pumping system, cost estimation and expenditure scheduling.

Jan 1, 2010

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By Paul Grisley

Air-supported belt conveyors-conveying systems that replace troughing idlers with a film of air-were a revolutionary concept when introduced in the 1970s. But high installation and operating costs limited their application. Now, system refinements have led to successful applications, even under the challenging conditions of mines and process plants. In this presentation the author will discuss the latest developments in the engineering of these systems, including the ability to retrofit existing transfer points with modular air conveyor components. Air conveyor applications and limitations in mineral-handling operations will also be examined.

Jan 1, 2002

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

By David Brown, Glen Hall, Ken DeVos, Frank Barone

Dredging and Flooding was completed on the Falconbridge Limited "New Tailings Area" in the period from 1996 through 1998, as part of their site closure measures. Part of the decision making process and closure planning was water quality prediction, including oxidation and diffusion modelling. The purpose of this modeling was to define the potential water quality that would result during and after dredging. A significant body of research on the geochemistry and oxidation kinetics of this site had been compiled. The results of the modeling provide practical insight on the potential water quality that may be expected. Water quality in the pond has steadily improved since flooding was completed with the exception of short term peaks during spring runoff. Aquatic vegetation is appearing through natural recovery and transplanting of local species, and colonies of minnows are now observed in the ponds.

Jan 1, 2000

By William E. Lamont

The Mineral Resources Institute (MRI) of the School of Mines and Energy Development (SOMED), University of Alabama conducted studies to determine the potential for upgrading the Eastern Devonian shales by flotation. Results of those studies indicate that flotation concentrates containing 150 liters of oil/t (36 gal/t) can be produced from shale containing 50 liters of oil/t (12 gal/t) as determined by Fischer Assay with good recovery of the kerogen. Organic carbon and trace elements such as molybdenum, vanadium and uranium also are concentrated with the kerogen. Kerogen concentration was found to be a function of the size of grind.

Jan 1, 1983

By Robert A. Bauer

Investigations of bedrock within subsided areas over abandoned coal mines reveal) very little disturbance of the bedrock. In areas that have surface subsidence of .3 to 1 m (1.0 to 3.25 ft), examination of cores from exploration drilling and investigations of the boreholes by means of closed circuit television have shown that fractures are spaced at least .9 to 3.6 m (3 to 12 ft) apart and are located within a zone 6 to 15 m (20 to 50 ft) above the collapsed area in coal mines 42.6 to 112.7 m (140 to 370 ft) deep. The dip of the fractures ranges from 25 to 60 degrees, cutting across nearly horizontal sedimentary bedding planes. Typical core recovery is 80 to 95 percent within the subsided areas and 100 percent outside the subsided areas.

Jan 1, 1984