Search Documents

The impact of a methane explosion on mining operations cannot be over-emphasized. The explosion is a result of rapid combustion when a methane/air mixture is ignited by an unexpected energy release, such as a mine fire, electrical arc or sparks caused by frictions or rock falls. In most cases, an ignition of methane/air mixture could result in a deflagration other than detonation. Resulting flames and overpressure induced by a methane deflagration will harm neighboring miners and local ventilation control devices.. ,It is essential that the mechanism of an explosion and associated destructiveness be fully understood. This research seeks to predict an influence region of an incident happened within a representative underground mine geometry. The most common geometric changes in an underground coal mine are bends, regulators/doors, obstacle in airways and changes in sectional area. These geometric changes could result in an attenuation of the flame and pressure wave as a result of a methane deflagration. A study of this phenomenon could enable mine planners to have better understanding of the over-pressure redistribution due to the explosion. Both numerical and experimental work has been done in this study to ascertain a better insight of this potentially devastating event. The experimental data are also used to validate the turbulence and combustion models used in this test.

Feb 23, 2014

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By Robert J. Willard

In its search for additional ways to increase understanding of rock behavior, the Twin Cities Mining Research Center has turned to the scanning electron microscope, an instrument rapidly finding application in research concerned with surfaces of materials. Since features indicative of the manner in which rocks fail may be recorded on the surfaces of fragments as disintegration proceeds, this microscope might be used as a tool for seeking and mapping these minute features. In pursuit of such features, we chose to scan a portion of the fracture surface from a quartzite disk compressively loaded to failure between two pins centered along the disk's axis. The resultant fracture appeared as a rough, diametric plane, and the fracture surface near one of the loading points was scanned with the microscope.

Jan 1, 1969

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959

By J. E. Sepulveda

Tar sand deposits in the. Stare of Utah contain more than 25 billion barrels of in-place bitumen, Although thirty times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion barrels), The term "tar sand" refers to a consolidated mixture of bitumen and sand, Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water extraction process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique., Experimental results indicated that, for a given tar sand sample, percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage, These variables were identified by means of an experimental, factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence gathered in this investigation seems to indicate that a hot-water extraction process for Utah tar sands would allow for the efficient utilization of this important energy resource.

Jan 1, 1978

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By Josiah Pohl, Christopher Utter, Kyle Everly, Akshay Chowdu

Battery Electric Vehicles offer increased energy efficiency for open-pit load & haul operations at a potentially lower overall carbon cost. Electrifying a mine’s fleet, however, presents a unique set of operational challenges. In this study, we explore the effects of electrification on productivity at real operations using a Discrete Event Simulator. The model can simulate multiple shifts, a mixed fleet of diesel and electric trucks, charging and refueling stations, trolley systems, and accurate shovel-truck loading cycles. This study helps determine the trade-offs of adopting electric fleets and how they interact with the layout of today's mines.

Jun 25, 2023

By S. D. Abbott

Mines are filled with a mixture of gases, some of which are toxic, flammable, or explosive. Others serve as early reporters of impending problems. Mines monitor these gases in order to ensure the safe, efficient operation of the facility and avoid losses or disasters. Two different approaches to monitor these gases have historically been taken. One kind of device measures the amount of each gas present by using selective detectors (e.g. handhelds and spectrometers). Another kind separates the mixture of gases into the individual constituents, then measures the amount of each gas present (e.g. gas chromatographs). Handheld units are the most widely used, but gas chromatographs are the most powerful yet underutilized units available to enhance mining operations. There are many misconceptions about the nature, applicability and proper use of each type of device, and little data is available. Up to this point, many people had only the manufacturers? claims to guide them. This study was undertaken to clarify the range of applicability, important characteristics, and value in use of these units in real-world situations. An additional goal of the study was to provide ways to evaluate comparative data, and thus aid mining operations in choosing the most beneficial and reasonable ways to use such devices in various situations and contexts.

Feb 23, 2014

By W. Reed

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This paper examines factors that had a significant influence on mine face ventilation design during the past century. Several “milestone” events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative ventilation designs and a consistent commitment to mining health and safety.

Jan 1, 2007

By T. Y. Yan

A method has been developed to remove calcite from the leaching circuit in the uranium in situ leaching system. The process involves injecting the leachate and a pH control agent tangentially into an inverted cone reactor containing calcite seed catalyst. The leachate can be treated at high throughput to obtain clear effluent containing 5 ppm or lower Ca. Both lime and ammonia are effective pH control agents and consumed according to stoichiometry.

Jan 1, 1983

By T. C. Vogt

Earlier we described the uranium mineralogy of an areally broad sampling of Crownpoint ore, including the characterization of organic carbonaceous material associated with the uranium mineral. (1) We also reported on the leaching behavior of Crownpoint ores with a mild alkaline leaching system, oxygen (02)-sodium bicarbonate (NaHC03). (2) There was a wide range of leaching responses, with samples from some areas leaching at a slow rate with low uranium recovery. Evidence indicates that in these samples the organic material is intimately associated with the uranium mineral and shields it to some extent from contact by the leachate. (1,2) One method to obtain faster leach rates and higher recoveries is to use a chemically severe leaching system such as sodium hypochlorite (NaOCI) as an oxidant. (3) The use of sulfuric acid (H2SO4) and an oxidant for leaching ore in surface milling operations is widely practiced to effect high recovery of uranium (U308) from the ore. (4,5,6) The U308 is mobilized as the disulfate complex, U02(S04)224-, or possibly, the trisulfate complex, U02(S04)34-, is the soluble species. (7) Sulfuric acid leachate formulations were used in the first in-situ leaching operation in the Shirley Basin in Wyoming. (8) More recently H2S04 formulations have been used in the Rocky Mountain Energy field tests in the Powder River Basin (Bear Creek) and in the Teapot forma¬tion at Nine Mile Lake site near Casper. (9,10) Laboratory studies related to the use of H2SO4 for in-situ leaching have been reported (11-17) and Yan has .reported packed column leach studies on Crownpoint ore using H2504 and oxidant. (18)

Jan 1, 1981

By R. W. Mossman, George E. Heim

Seismic exploration techniques offer the engineer and geologist a way of obtaining detailed information on the physical parameters and geometry of the rocks where extensive underground excavation or tunneling is proposed. Use of the seismic method can provide a greater amount of detailed information at relatively less cost than can be obtained by any other known subsurface exploration method. Boreholes are still required for calibration of the seismic data but at a much wider geographic spacing than otherwise would be needed for subsurface mapping. The seismic data can define with precision the actual location of zones of flexure or fracture of the rocks and reveal the configuration of the surface of the rock layers. ENGINEERING PROBLEMS One of the major requirements in the planning of subsurface installations is that of locating tunnels and other underground openings in favorable rock units. Such rock units should exhibit uniformity of composition, both vertically and horizontally, to minimize variation in excavation techniques. The depth and thickness of the unit must be known: a 30-foot diameter tunnel cannot be contained in a 25-foot thick limestone. The rock unit needs to be as free as possible from structural defects and should be suited to efficient excavation procedures. If liquid conduits are planned, the slope of the rock unit needs to be known so that maximum advantage can be taken of gravity flow with the tunnels wholly contained within the unit.

Jan 1, 1997

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By N. W. Johnson

Two analysis tools which have been applied to problems in industrial Flotation processses are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. The paper describes practical examples of the application of kinetics to examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.

Jan 1, 1985

By Elwyn H. King, Thomas R. Kuesel

I. CONCEPT MARTA's Peachtree Center Station is being mined out of hard rock, directly beneath Atlanta's central business district, with minimal surface disruption during construction. Its cost is competitive with that of a conventional cut-and-cover alternative owing to its design concept, which utilizes the rock as a primary structural and architectural material. II. PLANNING The station was originally planned for cut-and-cover construction. However, Peachtree Street is unusually narrow for a main business street (generally 78 feet (24 m) between building lines) and cut-and-cover construction would therefore be very disruptive to surface traffic and severely restrict access to adjacent buildings, including Peachtree Center, Atlanta's showcase business/commercial complex. (See Fig. 1.) Tunneling had been considered, but was initially thought [ ]

Jan 1, 1979

By D. R. Taylor

Treatment of bentonite clay with mineral acids yields a modified clay product of high surface area and acidity which exhibits enhanced adsorptive and catalytic properties. A highly specialized segment of the clay industry based on this process has evolved into worldwide business with a capacity of about one-half million tons/yr. This paper will present data on the chemistry, mining, manufacturing and applications for acid- activated clays.

Jan 1, 1986

Anomalous geologic or stress conditions ahead of the longwall face can cause great harm to both the individual miner and the mining operation as a whole. The U.S. Bureau of Mines has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of a field effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure, and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration, likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with laboratory measurements.

Jan 1, 1995

By Om P. Garg

The purpose of this paper is: 1) To summarize the capabilities and some of the limitations of the existing mine planning software. 2) To provide some guidelines for acquiring the software. 3) To identify problems and challenges in terms of how to justify increased use of computers (particularly the 32-bit microprocessor based super micro computers), for various activities related to a mining operation No attempt has been made to review the contents of available software packages in detail. Also the scope of this paper is limited to mine planning related computer applications. Applications related to accounting, inventory control, preventive maintenance, equipment scheduling, etc. have not been covered.

Jan 1, 1983