Search Documents

By R. W. Bartlett

High salinity geothermal brines typically contain up to several hundred parts per million of valuable heavy metals, and because of the large potential flow of geothermal brines from future power plants, metal production as a by-product could be significant A-planned 55-MW demonstration plant near Niland, California should generate enough spent brine to contain approximately $670,000 per year in gross metal values. Lawrence Livermore Laboratory estimates (1) a Salton Sea Geothermal potential of 1300 to 8700 MW, which would translate to possible yearly heavy metal values between $5,800,000 and .$l05,000,000. Since these estimates were made on a conservative basis, this geothermal reservoir is potentially a large ore deposit. The heavy metals in order of decreasing abundance in high salinity brines from the Salton Sea geothermal field are usually manganese, zinc, iron, lead, and silver. All but manganese and iron are valuable enough to be of commercial interest. Minor amounts of copper and arsenic are also present. Although heavy metal precipitates, particularly lead, have been found in scales within pipelines and obtained from steam flashing, most of the metals remain soluble during steam production; hence removal of the valuable metals from the spent brine before reinjection in ground reservoirs is indicated. Because the heavy metal concentrations are low, a very simple and inexpensive process is required. The heavy metal value in Niland brine is only ' about $1 per 1000 gallons; see Table 1. The brine composition shown in Table 1 was taken from one of the brine samples used in our study. Projected post-flash brine from a steam plant has somewhat higher Zn and Pb values, but the gross heavy metal value is still less than $2 per 1000 gallons.

Jan 1, 1980

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By G. Bonifazi

Certain deposits of incoherent materials which are near the surface and exploitable by open-pit mining may be characterized in real time before they are mined through an analysis of ground-surface imagery. If the slice to be stripped is not overly thick, in fact, surface texture and color properties may be extrapolated to its entire thickness. Image analysis techniques to process ground surface images acquired in situ (or in the laboratory shortly after their acquisition) which yield pattern vectors representative of RGB color component distributions and HSB texture parameters have been developed. The techniques were applied to a mineral sandy ore deposit containing three different lithotypes. Geostatistical analyses showed that the data used to characterize the lithotypes were reliable. The correct recognition of the lithotypes was carried out using a multi-barycenter classification algorithm. Such in situ image-analysis procedures open the way to the proper selection of the ore to be mined, or the proper way for run of mine (r.o.m). processing, or the appropriate blend to be processed before or at the same time as the mining process itself is enacted.

Jan 1, 1999

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By Gary L. Simmons

Noranda's Grey Eagle Mine and Mill, located in the Siskiyou Mountains of Northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mining, milling and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1984

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

Adsorption of acrylamide based homo and copolymers on hematite was investigated as a function of phe nature of the polymer charge and functionality of the polymer. Effect of addition of sodium dodecylsulfonate and dodecylamine hydrochloride was also studied and was determined to result in an increase or decrease in the amount of polymer adsorbed depending on, the charge characteristics of the surfactant and the polymer, pH of the suspension, concentration of the various species and the order in which these species were added to the system. The surfactant adsorption under given conditions on the other hand, was found not to be affected by the presence of the polymer molecules. The data is analyzed to elucidate the mechanism of adsorption of polyacrylanide type polymers on hematite both with and without the surfactant species king present in the system.

Jan 1, 1982

By M. J. Virnig

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-1 and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By C. A. Oestreicher

For sulfide minerals, the presence of dissolved oxygen in the water phase is an influencing factor for separation by flotation. Klassen and Mokrousov(I:217l distinguish three stages of oxygen adsorption; namely, reversible adsorption, activated adsorption and, finally, surface oxidation. While contraversial, limited adsorption of oxygen is believed to improve the interfacial reactivity between collector and mineral. Intensive surface oxidation of sulfide minerals usually results in unsatisfactory flotation with collectors of the xanthate type. The influence of dissolved oxygen in the water phase has received consideration for sphalerite, galena, chalcopyrite, arsenopyrite, chalcocite, and covellite(2,3,4,5,6). However, the nature of surface oxidation products of sulfide minerals has received very limited investigation(6,7). Lightly oxidized galena promotes the adsorptive reaction of surfactant (xanthate or dixanthogen). Tolun and Kitchener(8) state that limited interaction occurs between galena and xanthate under relatively reducing conditions. And, that exposure to oxygen raises the electrochemical potential of the galena to that required for reaction with xanthate or dixanthogen. In the latter condition, the galena has an "effective flotation surface". On the other hand, intensive oxidation of galena reduces the chemical reaction with xanthate collectors (9) . Complete flotation with xanthate-type surfactants with increasing oxygen content in the water phase has been determined to have the following sulfide mineral sequence(3): galena, pyrite, sphalerite, chalcopyrite, pyrrhotite and arseno-pyrite. The work of Cusack(4) suggests that some threshold amount of oxygen is necessary for flotation to occur, but heavy oxidation hinders flotation with xanthates. According to Tolun and Kitchener(8) catalytic oxidation of xanthate to dixanthogen occurs. From infrared studies, Poling and Leja(IO,II) found that in the absence of oxygen in solution, xanthate ions do not adsorb either on

Jan 1, 1972

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By Brandon Barnes, Michael Haggerty

"Around Minneapolis and Saint Paul, Minnesota, the local geology includes the St. Peter Sandstone, which is easily minable and has facilitated construction of interceptor tunnels for storm water and sanitary tunnels since the 1800s. The elevation of the geologic units allowed gravity-driven flows from the downtown areas all the way to the Mississippi River. Through many years of service, some of these tunnels have experienced degradation and require maintenance. Additionally, increased stormwater surface runoff can result in internal pressurization of the tunnels, accelerating degradation. Because structural failure or collapse of any of these interceptor tunnels would create a significant repair challenge, the city of Minneapolis has been inspecting and designating tunnels in its system for periodic review and repair. One of these, the St. Mary’s/Hiawatha tunnel, was rehabilitated using a grouting program. A hydrologic model was also used to improve understanding of pressurization events during some storms, leading to construction of a near-surface pressure dissipation chamber to provide increased hydraulic capacity. BACKGROUND The St. Mary’s/Hiawatha tunnel in Minneapolis has three segments; the first two were constructed in 1942 and the third was added in 1987 (Figure 1). Segment 1 is approximately 4,700 feet in length and outlets to the Mississippi River. Segment 2 intersects Segment 1 approximately 3,500 feet upstream of the river outlet and continues for approximately 2,500 feet in a southeasterly direction. The third and newest segment is approximately 500 feet long. There are four different cross sections of tunnel along the entire system.Originally, tunnel construction often consisted of mining the St. Peter sandstone with a pressurized water lance and constructing wood lagging support (Payne, 1967). An underdrain was generally installed below the invert during construction; this resulted in localized dewatering and provided groundwater control during construction. Non-reinforced concrete liner sections were cast in place. Often void space existed between the tunnel liner and the native sandstone bedrock. These voids, particularly in the crown, prevent direct contact between the liner and the bedrock."

Jan 1, 2016

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By Cristian Saavedra, Patricio Zarate

Flotation collectors play a crucial role in mineral flotation by selectively adhering to mineral surfaces and aiding in their separation from gangue material. They are heteropolar molecules, as defined by Sutherland and Wark (1955), featuring non-polar hydrocarbon chains and polar groups interacting with mineral surfaces to induce hydrophobicity selectively. The importance of collectors in mineral processing, as underscored by Lotter and Bradshaw (2010), lies in their ability to enhance recovery rates and improve selectivity, thereby optimizing the extraction of valuable minerals from complex ores. Collectors are classified based on their mechanism of action, as proposed by Laskowski (2010). This classification categorizes collectors into three groups: water-soluble compounds, water-insoluble “oily” collectors, and water-insoluble amphipathic compounds forming molecular films at the water/gas interface. This complements the chemical structure-based classification by Sutherland and Wark (1955) and Suoninen and Laajalehto (1993), offering a comprehensive understanding of collector diversity in flotation systems. Collector selection is an iterative process crucial for optimizing mineral processing efficiency, as emphasized by Lotter and Bradshaw (2010). Understanding the significance of collector mixing or synergy outcomes is paramount for enhancing mineral flotation efficiency and sustainability. Taguta, O’Connor, and McFadzean (2018) demonstrate that mixed collector systems enhance interaction enthalpies and microflotation recoveries, indicating improved performance. McFadzean, Castelyn, and O’Connor (2012), along with Critchley and Riaz (1991), delve into investigating synergistic interactions between collectors, offering insights for strategic selection. Observations from the study of collector synergy, as noted by Wakamatsu et al. (1980), reveal nuanced relationships surpassing individual collector behaviors. The methodology outlined in this paper provides valuable guidance for classifying and selecting collectors based on specific application needs, while also suggesting the potential for synergistically improving recovery across fine, intermediate, and coarse particles.

Feb 1, 2025

By S. Goodfellow, J. C. Ordóñez-Calderón, K. Esmaeili, N. Houshmand

A good understanding of the hardness of ore being handled and processed in a mining operation can significantly improve operational efficiencies by providing valuable data to support decision-making through the mining value chain (drilling, blasting, comminution). This study presents the results from the application of Machine Learning (ML) to predict rock hardness using various geophysical and geochemical features. Core samples from a mine site were logged using a multi-sensor core logging system. Measurements including ultrasonic p-wave and s-wave velocity, elemental concentration via portable XRF, and Leeb Hardness, were measured every 2 cm along the length of the core. The ML model was set up to predict the Leeb Hardness using the elemental concentrations and ultrasonic velocities as predictors. The Leeb Hardness values were grouped into three bins and used as a classification target for the ML models. Various ML models, including linear regression, support vector machines, decision tree, XGBoost, Random Forest, K-Nearest Neighbors, and Naïve Bayes were tested. The model performance demonstrated that the Random Forest and XGBoost models produced the highest accuracy of 74-91%. Random forest and XGBoost were then selected to perform regression models to estimate a Leeb hardness value rather than a hardness class. These models were able to estimate the Leeb hardness value by 4.57-4.87 % error.

Mar 2, 2022

By William Bergeson

"BACKGROUND As of December 2015, there are roughly 475 road tunnels within the United States according to the most recent national tunnel inventory data compiled by the Federal Highway Administration (FHWA); whereas, there are more than 615,000 highway bridges on public roads. The FHWA estimates that tunnels represent nearly 100 miles of Interstates, State routes, and local routes. Tunnels are part of the national transportation infrastructure and represent a significant financial investment for the owner and, hence, the tax payers. Tunnels, that are not properly maintained, usually require more extensive repairs and consume more resources. Tunnels must provide safe, reliable, and effective transportation even as these structures age and deteriorate. Furthermore, tunnels generally remain in service for extended periods of time due to their very high construction costs. For example, many tunnels were constructed decades ago during two historic periods of highway system expansion; the first period correlated with the era of public works programs linked to the Great Depression of the 1930-40s; and the second period of expansion occurred with the building of the interstate highway system in the 1950-60s. As such, these tunnels are fast approaching 60 to 80 years old. Congress enacted the Moving Ahead for Progress in the 21st Century Act (MAP-21), which was signed by the President on July 6, 2012. This legislation followed a fatal tunnel incident on July 10, 2006 and a National Transportation Safety Board (NTSB) report1 that noted the importance of conducting regular tunnel inspections. MAP-21 authorized the Federal Highway Administration (FHWA) to develop a mandatory inspection program for all tunnels on all public roadways (Bergeson and Ernst 2015): To help safeguard tunnel users and to ensure reliable levels of service, the FHWA developed the National Tunnel Inspection Program (NTIP), which is comprised of the National Tunnel Inspection Standards (NTIS), the Tunnel Operations Maintenance Inspection and Evaluation (TOMIE) Manual, the Specifications for National Tunnel Inventory (SNTI), and the Manual for Bridge Evaluation (MBE). The data collected from the program will be stored in a National Tunnel Inventory (NTI) database. A comprehensive and refresher training program was also developed to help qualify and certify key tunnel inspection personnel to include the program manager and team leader."

Jan 1, 2016

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By C. Clark, R. Pakalnis, B. Seymour, L. Martin, R. Jacksha, M. Stepan, M. Roworth, C. Caceres

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, a rugged, portable direct tensile test system was developed for measuring shotcrete adhesion strength in underground mines. During the development of this test system, more than 185 direct tensile tests were conducted with a common, commercially available macro-synthetic fiber-reinforced shotcrete that was applied to concrete test panels using a dry mix process and machinery. The average bond strength of the shotcrete to the concrete substrate typically increased as a function of the shotcrete’s curing age, ranging from 0.44 MPa (64 psi) after one day of curing to 1.58 MPa (229 psi) after 90 days of curing. Adhesion strength increased markedly between one and three days of curing, reflecting a similar trend of increasing shotcrete tensile strength with curing time. This robust direct tensile test system can improve mine safety by providing a reliable means of measuring shotcrete adhesion strength and also supplying important information about the quality of the applied shotcrete and the competency of the underlying rock.

Jan 1, 2010