Search Documents

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By M. Z. Mubarok, Z. T. Ichlas, A. T. Sugiarto, K. Sukamto

The use of ozone as an oxidant for the direct leaching of zinc sulfide (sphalerite) concentrate in sulfuric acid medium under atmospheric pressure was explored. The influence of acid concentration, feed gas injection rate, particle size distribution, stirring speed, temperature and slurry density on zinc extraction efficiency was examined. The experimental results showed that the leaching efficiency depends on all of these operating parameters except for stirring speed. It was found that essentially complete dissolution of zinc from the concentrate with the present method can be achieved in only about seven hours under the conditions of sulfuric acid concentration of 2 mol/L, particle size smaller than 74 µm, slurry density of 50 g/L, stirring speed of 420 rpm and feed gas injection rate of 1 L/min at ambient temperature. The experimental results suggest that the dissolution reactions produce independent elemental sulfur that is readily floated and can be easily separated rather than forming a layer on the surface of the reacted particle, as usually observed in a system with ferric-sulfate as oxidizing agent. It was therefore determined that the dissolved ozone play a key role in improving the rate of zinc dissolution from the concentrate. Analysis of the leaching kinetics indicate that the leaching rate follows the shrinking particle model, and the overall dissolution rate of zinc is controlled by a surface reaction.

By James M. Griffin

It was not many years ago that people would have argued that a coal session did not belong at an International Mining Convention. Historically, steam coal has always been used domestically due to its natural geographic diversity and high transportation expense. Times have changed. With the help of Opec, steam coal has gone international. As opposed to metallurgical coal, whose trade routes have a long history, whose supply sources are more limited and whose market growth is seen by most to be relatively flat, steam coal export forecasts are calling for more than a doubling by 1990 and a quadrupling by the year 2000. Suddenly, one must be familiar with coal mining on a global basis in order to predict which regions will be able to fill these markets.

Jan 1, 1982

By G. T. Lineberry

There is a critical need for effective instructional materials at the university level and for an upgrading of mine safety and health in the mining engineering curriculum. A fundamental approach to mine safety and health is recast into the familiar 3 E's: engineering, education, and enforcement, in that order. Each is briefly reviewed and their interdependence emphasized. A unique philosophy for successfully integrating safety and health principles into the mining engineering curriculum is offered. The concept of textbook ?tailoring? is discussed and defended, permitting rapid assemblage and synthesis of existing educational materials. Final recommendations are made for a u, comprehensive approach to mine safety and health education in the undergraduate curriculum.

Jan 1, 1987

By J. N. Cox

Coal preparation is based on the properties of noncombustable materials (impurities) in coal being different from the organic constituents. The most commonly used property difference is density, via its affect on settling rates; and either gravitational or centrifugal forces can be used to remove impurities. However, examination of various particles settling rate correlations shows that at smaller sizes, particle drag becomes a very important factor. Classification, based on differential settling rates, becomes impractical and some property other than density must provide the basis for fine coal cleaning. Froth flotation and agglomeration employ differences in surface properties to clean coal. These methods are very successful except that the oxidized surface of a pyrite particle is somewhat hydrophobic and will tend to be collected with the organic portion of the coal. Surface property cleaning techniques have not been very effective in rejecting sulfur, except for two-stage flotation.

Jan 1, 1984

By D. A. Robbins

The application of remote sensing for environmental measurements is already being utilized. Aircraft mounted imaging spectroscopy has been utilized to evaluate areas of historical mining operations as well as active mine sites. To the extent that remote sensing can provide more sensitive, cost effective, and timely monitoring potential, the technology is of interest to the industry. Questions remain about the application and validation of the data and the availability of the technology in the private sector. This presentation will discuss some of the potential uses, benefits, and concerns related to remote sensing and efforts to monitor the technology's development.

Jan 1, 1999

By J. Z. Keating

There are close to two million tons of Industrial Minerals processed and sold in North America wherein the processor/marketer has no affiliation with the source mine. The largest quantity, about 800,000 tons, is barium sulfate, which is sourced in lump ore form mainly from China and India. The Alumina Trihydrate Industry sources several hundred thousand tons from various alumina refineries. Substantial quantities of bauxite, zircon, magnesite, and fluorspar arrive in North American ports each month. There are also rapidly growing quantities of offshore talcs and calcium carbonate ores being processed in U.S. plants. These feedstocks are usually quite pure, have unique properties, and enjoy bulk rail or waterborne freight economies that allow successful competition with locally sourced raw materials. With increasing restrictions on mining activities, and the increasing need for sophisticated functional minerals, the importation of minerals will continue to grow.

Jan 1, 1994

By Dai Wang

Stoppings are necessary ventilation control devices for effective air distribution underground. However, one of the major problems underground mining has is that every stopping is a potential leaking source. Since air always flows from a point of high pressure to one of lower pressure, and the total pressure at every point in intake airways is higher than that in the return airways, air will always tend to leak from intake to return (Tien, 1996). In many mines, less than half of the air entering the mine actually gets to the working areas; the rest of it simply short-circuits directly to return airways through leaky stoppings instead (Timko and Thimons, 1983). Leakage through a stopping occurs because of pressure drops across the stopping and available leaky path in stoppings. Empirical equation has been widely used to characterize the relation the amount of leakage and variables that affect leakage. However the use of this equation requires accurate information for constants which are not always readily available. It is the attempt of this paper to derive an equation similar to the Atkinson Equation that can readily be applied to characterize pressure-leakage relationship for any given stopping.

Jan 1, 1998

By Yoshinori Shimada, Oleg Kotiaev, Hiroaki Sakamoto, Toshihiro Asakura, Naotoshi Yasuda, Norikazu Misaki, Masahiro Shinoda

"To ensure that trains run safely, the performance of railway civil engineering structures is checked by periodic inspections. General inspection method has merits and demerits, but none of them offers the combination of high accuracy and quick inspection. In an effort to resolve this problem, West Japan Railway Company, the Institute for Laser Technology and the Railway Technical Research Institute jointly developed a remote laser sensing system as an alternative to the impact acoustics method for detecting defective concrete elements in tunnel linings. The proposed remote laser sensing system has two lasers, one to apply an impact to the concrete surface and the other to measure the vibration of the concrete generated by the impact laser. The impact laser is a high-energy pulse laser that induces vibration in the concrete. The detection laser has a signal beam and a reference beam. The signal beam reflects on the concrete surface and goes into the dynamic hologram crystal. The reference beam diffracts in the dynamic hologram and enters the detection sensor with the signal beam. The vibration of the concrete surface can be measured to detect the movement of an interference pattern. A prototype of the remote laser sensing system was developed as shown in Figure1. A vibration and acoustic insulators are equipped to remove a noise generated from a maintenance car or electric generator in this system. The proposed laser remote sensing system and the detection algorithm were verified with the help of field test conducted in a tunnel on the Shinkansen. An impact test using hammering was applied to obtain the accurate response acceleration on the surface of the concrete before application of the proposed method. In this test, the result obtained from the proposed method has good agreement with that obtained from the impact test by hammering. Consequently, it is verified that the proposed method can be used as an alternative to the standard impact acoustics method."

Jan 1, 2016

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By M. Ziegler

The article deals with the use of a digital twin in the assessment and optimization of a conveyor system in the Chilean copper mine. This example shows that a digital twin is initially just a new (albeit powerful) tool with which the system behavior can be examined. The benefits for the customer arise through the system identification and automatic detection of critical deviations from the target state. This knowledge allows mine management to react and coordinate operational and/or maintenance counter measures to insure optimal performance of their conveyor system. The information derived from the BeltGenius digital twin also allows mine management to gain a clear perspective of the overall efficiency of their conveyors, which will be invaluable for future conveyor component selections.

Mar 2, 2022

By Joseph Moses Botbol

Two methods are developed whereby; (1) mineralogic data can be arranged in order of typicality, and (2) mineralogic data external to a model can be compared with the model and the degrees of association computed. Thirty arbitrarily selected base metal mining districts in the conterminous United States were classified as copper, lead, or zinc districts on the basis of tonnage of the major base metal produced. For each of the copper, lead, and zinc districts binary-occurrence distributions were compiled for primary (unoxidized) and secondary (oxidized) minerals. Primary and secondary minerals were then arranged in order of decreasing typicality. Model copper districts are most typified by primary chalcopyrite, pyrite, and secondary malachite. Model lead districts are most typified by primary galena, quartz, pyrite, sphalerite, and secondary anglesite and cerargyrite. Model zinc districts are most typified by primary sphalerite, galena, pyrite, quartz, and secondary smithsonite and cerus-site. The Park City district was removed from the model and its primary and secondary mineralogy was compared with the model copper, lead, and zinc districts. The primary mineralogy of the Park City district is about equally associated with the model copper and lead districts, but the secondary mineralogy is much more akin to the model copper districts. Thus, with respect to the model data, the geochemical target presented by the Park City district resembles a copper district more closely than a lead district.

Jan 1, 1969

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

By R. Flores V.

The Refugio Project is located in the Andes mountains of northern Chile, in the Maricunga Hineral Belt. The Verde, Pancho and Guanaco Au ore bodies have been recognized and are Early Miocene in age. Mineralization consists of fine-grained disseminated gold hosted by dacitic to dioritic subvolcanic porphyries. Alteration comprises massive to veinlet-controlled silicification overprinted on earlier potassic and propylitic alteration and surrounded by later argillic alteration. Geologic relationships suggest that the Refugio ore bodies occur within an Early Tertiary volcano overlying Paleozoic and Mesozoic basement rocks. Geologic reserves at Refugio are approximately 300 million grams (9.7 million ounces) of gold. The Verde deposit contains 185 million tonnes of mineable and leachable ore with an average grade of 0.90 glt Au and is currently in the pre-construction stage after a positive feasibility study. Proven and probable mining reserves at Verde deposit are 101 million tonnes at an average grade of 1.02 glt gold. Additional potential exists at to other deposits within the Refugio property (Pancho and Guanaco) but no reserves have yet been defined due to the limited drilling to date.

Jan 1, 1994

By D. Shuck

Incorporation of a 2,727 mtpd, $5.7 million flotation circuit into the Mclaughlin flowsheet was completed in November 1991. This capital addition reduced overall operating costs and improved the gold recovery of the low grade refractory reserves over that expected for direct cyanidation. In addition, flotation provided a means to generate a sulfide concentrate which is utilized to supplement feed to the pressure oxidation circuit.

Jan 1, 1994

CVRD was established on June 01, 1942, during the Second World War, through an agreement between Brazil, the United States and the United Kingdom, to produce 1.500.000 tons/year of iron ore from Itabira mines in the State of Minas Gerais. As a result of several circumstances and political problems (the end of the 2nd World War reduced the Anglo-American support to its development and implementation), the venture just reached the originally targeted production 10 years after its establishment, operating within a mine, railway and port integrated system. Currently, this operational system from the South of Brazil owns mines in the State of Minas Gerais with an annual capacity of approximately 65 million tons, 900 km of railways, of which more than 500 km is a double line railway, six pelletizing units and the Port of Tubarao for ships with large carrying capacity.

Jan 1, 1994