Search Documents

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010

By T. Kelly

The Cannon Mine is located in Chelan County, near Wenatchee, Washington, at the eastern foot of the Cascade Mountains. The mine is situated about two miles from the Columbia River, in the arid Columbia River Valley. Two hydroelectric dams provide electricity for the area, the Burlington Northern Railroad has a switch yard and loading facilities in Wenatchee. Approximately 25,000 people live in the area. The principal industry is fruit farming. Underground mining techniques are used to provide feed for a 2,000 tpd flotation concentrator at the site. The techniques are low- cost, high productivity methods which allow for a high extraction rate along with a high rate of recovery of the minable reserve.

Jan 1, 1986

By Robert M. Cox

Surface mining of coal in the South developed into a major industry during the 1960's. The economic significance of the industry is much greater than is readily apparent when one considers only the value of the coal mined. The abun-dant supply of relatively inexpensive steam coal for electric power generation that has been derived from the surface mines has provided the foundation for the industrial expansion that has occurred throughout the South. The region, in gen-eral, has enjoyed the benefits of plentiful low cost electric power. However, re-cent political decisions, at all levels of government, threaten to destroy or severely curtail the surface mining of coal and eliminate the economic advantages once enjoyed by the region. These political decisions are rapidly changing the basic rules of operation and fundamental economics of surface coal mining. Recent changes, resulting from the enactment of environmental and health and safety laws and various bureaucratic rules and regulations, have had a three-fold effect: 1) Greatly increased operating cost, 2) increased lead times for mine development, 3) limited potential reserve base for future mining. Also current legislative proposals are casting a shadow of uncertainty over the future of all coal mining operations that has created serious delays and in-creased cost for the expansion of the coal industry necessary to meet our project independence goals. Technology Surface mining is the safest and most economical way to produce raw materials from the earth's crust. It also affords a more healthier working environment for the individual miner. Surface coal mining now accounts for more than 60 percent of the annual coal production in the South. Surface mining of coal requires the removal of the overburden to expose the

Jan 1, 1977

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

This paper is aimed at helping the mining industry to better understand the challenges posed by electromagnetic interference (EMI) and to promote electromagnetic compatibility (EMC) in underground coal mines. The paper begins with a review of EMI standards in other industries, then presents some representative examples of EMI instances that have occurred in the mining industry, followed by a literature review of published EMI research in mining and, finally, a discussion on mitigation strategies and practical considerations related to EMI in mining.

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"The early mining of iron ore in Minnesota was carried on with the most primitive kind of tools. The pioneers used only such equipment as could be packed from Duluth through one hundred miles of forest to the first mines on the Vermilion Range and the operations were carried on with picks, shovels, hand drills and wheelbarrows, the ore being hoisted in buckets with a horse winch and carted in horse drawn wagons to the stockpile. This was about the extent of the mechanical equipment of the Minnesota iron mines in the early eighties.As soon as a railroad was pushed through from Two Harbors to the Vermilion Range the equipment began to be improved upon; wood burning steam boilers were installed and small steam puffers displaced the horse-winches, wheelbarrows were aban¬doned and small cars were introduced. Hauling the hoisted ore in wagons was discontinued and trestles were built so that the ore could be stockpiled more cheaply through the use of cars and high piles. These same stockpiles were loaded by hand into the 10 and 15 ton capacity railroad ore cars.Within a few years a marked change took place—the hand drill gave place to the air drill, such as No. 3 Rands, Ingersolls, Sargents and some Sullivans. Tramming was done by mules, the ore hoisted in. self-dumping skips, hoisting engines were intro¬duced and it seemed as though mining as a business in Minnesota had come to stay. At this stage someone conceived the idea of making the stockpile floor about three feet above the top of the ore cars to facilitate the hand loading of stockpile ore for trans¬portation. This was done through the use of wheelbarrows at first and later by using I-ton cars running on tracks laid on the stockpile floor."

Jan 1, 1920

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By Emily Sing, Ashim Gajurel, Thomas Pennington, William Brown

The Pardee Chemical Feed Shaft Project involves construction of two new chemical feed shafts to improve raw water treatment capabilities at the East Bay Municipal Utility District’s (EBMUD) Pardee Reservoir in Valley Springs, California. The project includes construction of two 250-foot deep, 16-inch diameter stainless steel chemical feed shafts that penetrate an existing 8-foot diameter concrete lined conveyance tunnel. The design approach required the shafts be installed using top-down drilling methods and within a strict verticality tolerance (0.1%). Innovative precision drilling techniques ensured that the shafts penetrated the tunnel in their planned locations and the installed chemical feed lines would function as designed. Challenges included extremely limited access to the tunnel because of a requirement to maintain the tunnel in service during construction. This paper discusses the overall project’s design and construction approach, including unanticipated conditions that the project team faced and how these conditions were managed and overcome through collaboration between the contractor, designer, and owner.

Dec 1, 2022

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By N. C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U. S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, preliminary results, and remediation ideas based on field observations are presented in this paper.

Jan 1, 1995

By Harry M. Parker

Exploration for sandstone-type uranium ore bodies which will be exploited using underground mining techniques is usually executed in sequential fashion. Geostatistical methods can be used at the earliest exploration stages to design drilling programs which have a high probability of success in the location and delineation of mineable ore-grade mineralization, should such mineralization exist. In succeeding development stages, geostatistics may be used to outline and define the potential grade of reserves and to apply confidence limits on the grade estimation. Delineation of mineable reserves for mine planning requires extensive development drilling; using such drilling data geostatistical methods may be used to minimize the drilling needed to achieve a desired level of confidence in the calculation of mineable uranium ore grade and tonnage. Because sandstone-type uranium deposits tend to be pod-shaped and are generally aligned along a mineralized trend, this paper proposes a geostatistical method of calculating uranium ore reserves which accounts for this fact and predicts the area within a trend which is underlain by ore. This method uses an indicator value; that is, drill holes which contain mineable ore-grade intercepts are coded as 1, those that do not are coded 0. The indicator may be kriged over the mineralized trend to obtain an estimate of the area underlain by ore. The thickness and grade-thickness may be kriged, and the average ore grade may then be obtained by dividing grade-thickness by thickness, as is conventional for stratabound deposits. The mean grade is then multiplied by the kriged mean thickness to obtain an estimate of the volume, and thence tonnage, of mineable ore within the trend.

Jan 1, 1979

By F. Shigeyoshi

The development of pelletizing during the last ten years has continued, however, self-fluxing pellets have not been regularly and commercially produced for use in blast furnaces, except as Kobe Steel, Ltd., Japan. This paper tells about unique developments for self-fluxing pellets, and their effects when used in Kobe Steel's No. 3 blast furnace at the Nadahama Works (inner volume 1845 Nm3, hearth diameter 9.5 m)., Several phases of the pelletizing process are discussed individually, and also their relation to performance in blast furnace operation. Special emphasis is placed on proper preparation of the limestone added to the raw materials, and indurating at optimum conditions. Means of improving pellet quality by correct control of size distribution of the raw materials used in pelletizing, and indurating temperatures, are also discussed. As basicity (CaO/SiO2) of pellets increased 0. 1, coke consumption decreased 3. 8 to 4. 2 kg per ton of hot metal, when using 70% pellets in the iron burden.

Jan 1, 1969

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By Tony Dunn

FMC Corp. achieved a significant cost reduction at its Green River, WY soda ash operations using a new proprietary solution-mining and processing technology. In phase one of the program, trona ore is dissolved, recovered and processed with the new technology. It is then fed into an existing refining plant, replacing dry mined and calcined trona ore. Phase two produces a final high-purity product. It also increases capacity by 635 kt/a (700,000 stpy). Both phases were completed under budget and ahead of schedule. This $120-million expansion project uses a new process and a new team to derive soda ash in a more cost-effective and environmentally friendly manner. The team successfully introduced solution-mining technology - with a liquid solution injected into previously mined sections of the mine. This shift in techniques signified a new era for soda ash production. The project is an example of teamwork at its best. For it to be successful, FMC had to work within several different areas inside and outside of the company. Engineers, contractors, mechanical operators and technical people were needed who could blend in with FMC's existing in-house team.

Jan 1, 1999

By Rodrigo Peroni, Vitor Campos

Carajás is one of the largest open pit mines in the world. The mine is comprised by a haul road network more than 100 km long, where the need for good roads is paramount and determining of the truck performances. This work integrates, regarding the ultimate pit design, an approach to consider an economic value to an originally unfit material, assuming it has the appropriate characteristics for haul road construction, which sometimes lies over economic iron ore. This measure demonstrated an improvement in the utilization of resources and guarantee the necessary material to the haul road design and Mining Pads maintenance.

Jun 25, 2023

This treatise presents the application of the vertical furnace in a carbon regeneration system. Comparison is made to a rotary kiln. The construction, operation and control of the vertical furnace and system components are discussed. Advantages include high efficiency, fuel economy, minimal mechanical apparatus and maintenance, atmospheric and temperature control, ease of operation and reliability.

Jan 1, 1985

By J. C. Draper

This subject was introduced last April in a paper presented in Birmingham, Alabama, by James E. Elkin, General Superintendent of Duquesne's Coal Department. This paper will cover some of the same data and in addition it will update and further describe our experience. Our Portal No. 3 was started in June 1965 with battery tractor-trailer face haulage. This mine is operating in the Sewickley seam in Dunkard Township, Greene County, in Southwestern Pennsylvania as shown on Fig. 1. The Warwick group of mines fronts on the Monongahela River and extends westward for some ten miles as shown on Fig. 2.

Jan 1, 1968

By R. N. Browne

As man searches unexplored horizons for new and economic industry, he must be constantly and acutely aware of the presence or absence of that precious commodity without which Industry, indeed Man himself, could not survive --W ATE R. The water requirements of the world today are magnanimous, considering that in 1960 the estimated consumption in the united States was over 300 billion GPD (1) or more than 1,700 GPD per person (5). The magnitude of the problem can be visualized as one considers that three times this quantity of water will be required in the united States by the year 2 000, when the dependable supplies of water are estimated to be only two-thirds of that required(2). How, then, can we continue to wreak such havoc on that life-sustaining substance -W ATE R? It is necessary, indeed mandatory, that those engaged in the Engineering profession consider it their moral obligation, not only to conserve the quantity of water which their conceived projects may require, but also to treat the effluent in order that the eutro-phication of natural water courses not be abnormally accelerated. The International Nickel Company of Canada Limited consumes some 33-1/2 millions of gallons of fresh water daily at its nine town-sites, fourteen mines and eight plants throughout the Sudbury district of Ontario. The present daily reuse of water exceeds 100 millions of gallons in the same area. It is noteworthy to mention that the milling rate has increased from 46,000 to 70,000 tons per day during the past five years, with no increase in water consumption. In fact, there has been a reduction in fresh water requirements.

Jan 1, 1971