Search Documents

By MOHAMMAD R. H. GORAKHKI, CHRISTOPHER BAREITHER, MANUEL APARICIO, IV JOSEPH SCALIA

Comingling filtered tailings and waste rock in a tailingsdominated mixture is a mine waste management strategy that has the potential to create geotechnically and geochemically stable landforms. Potentially acid-generating (PAG) waste rock can be sequestered within a filtered tailings matrix to enhance water retention and decrease hydraulic conductivity relative to a waste rock pile, potentially minimizing acid rock drainage (ARD). Enhanced water retention can reduce oxygen ingress limiting oxidation and resultant acid generation. Reduced hydraulic conductivity can slow inward percolation and outward drainage. In dry climates, the tailings matrix can hold precipitation near the ground surface accessible to evaporation and transpiration, thereby decreasing percolation. This paper presents an evaluation of comingled filtered tailings and waste rock in a tailings-dominated mixture (termed GeoWaste herein) and illustrates that ARD can be reduced under field conditions in a subtropical–highland climate.

By Michael J. Beus, Jan G. Patricio

INTRODUCTION The U.S. Bureau of Mines, Spokane Mining Research Center, has been conducting and documenting rock mechanics research in the Coeur d’Alene mining district for the past ten years (1, 2, 3, 4, 14, 15). A current project combines the information gathered from rock mechanics instrumentation, geologic structure, and analytic techniques to improve shaft and support design for the deep mines of the district (3). This project required knowledge of the anticipated loads and the physical properties of the rock mass to provide accurate input data for computer design models. Several techniques have been utilized to determine the physical parameters including the USGS (U.S. Geological Survey) solid inclusion probe, the CSIR (Council for Scientific and Industrial Research) biaxial and triaxial strain cells, and the CSM (Colorado School of Mines) dilatometer. This paper describes the determination of the in situ modulus of deformation in three mines over a period of three years and the evaluation of these results as they applied to this project. The need for in-situ rock mass properties such as the modulus of deformation has stimulated research and development of a large number of instrumentation techniques. One area of continuing interest involves various methods of radial borehole dilation. This concept was pursued by Menard (9) with an apparatus known as the pressure meter, which is used frequently in soil mechanics. Other developments in rock mechanics include the CPC (cylindrical pressure cell) by Panek (11) and the dilatometer by Rocha et.al. (13) in Portugal. The CSM dilatometer, which also utilizes this technique, was chosen for this project because it required a small amount of background study, was inexpensive, and could easily be combined with other experiments being planned for the test locations. Although no previous field applications to hard rock (compressive strengths greater than 20,000 psi) has been documented, the instrument was selected since good results have been achieved in granite, oil shale, and several coal measure rocks (11, 12).

Jan 1, 1977

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By Jamal Rostami, Omid Frough, Wei Hu

Characterizing the abrasiveness of soil/rock and the allowable wear of hard-facing products in various conditions is a critical factor in selection of the best material for certain applications related to drilling and excavation in mining and construction industries. The Soil Abrasion Index test machine at Colorado School of Mines (CSM) is one of the recently developed unique systems capable of testing soil/crushed rock abrasion under various conditions, such as dry, wet, and saturated settings. It is also capable of testing the performance of various types of hard-facing materials in a given geo-material. This paper studies the wear properties of different hard-facing materials in various crushed rocks from a surface mining operation in the iron range region of the USA. The hard-facing materials include regular and hardened steels and six different specialized hard facings, based on chromium carbide. The soil/rock include a standard sand and two rock samples from the surface mine. Fourteen abrasion tests were conducted, where the weight loss of each hard-facing material was measured over timespans up to 1 h of testing. The results show the distinct performance differences between the steels with 17 HRC and 43 HRC hardness and the hard-facing products for this application. The results show the possibility to evaluate the abrasiveness of different rocks at a mine or construction site and the performance of various hard facings in similar working conditions. This is a practical solution for selection of the cutting tool or reinforcement of bucket lips and truck beds for comparison of relative wear life between different wear-resistant materials.

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By C. J. Toberman

Improvements in fine (28x0) and ultrafine (200x0) coal cleaning is an acknowledged goal with potential benefits in both steam and metallurgical coal markets. This work focuses on adaptation to fine coal flotation of FLOTE, a computer simulation model of the froth flotation process originally developed in the hard minerals field. FLOTE describes the flotation of solids based on particle surface activity, composition, and size. The quasi steady state model was applied to predict flotation performance at an Eastern Kentucky, full scale metallurgical coal preparation plant. Parameter estimation and model testing used detailed flotation test data from a five stage rougher flotation bank. Overall grade/recovery predictions compared well with known plant performance under variation of principally feed grade, plant throughput and reagent addition; however, grade/ recovery predictions for each cell weaken under overloading conditions. Analysis of grade/recovery over a range of sizes is presented. Suggested model improvements and extensions are discussed.

Jan 1, 1984

By Qingwen Shi, Brijes Mishra

Laminated rock can delaminate and fail under certain stress states. Delamination-caused roof fall and cutter roof failure is a common failure mechanism in roadways in Pittsburgh coal seam due to the existence of laminated shale roof. Two-dimensional numerical models were developed at laboratory scale based on the bonded particle method in order to simulate the delamination with particle flow code. In these models, an assembly of bonded particles and parallel weak planes represents the laminated rock. This model calibrated the micro-parameters of the bonded particlematerial and weak planes with laboratory data. The mechanism of fracturing and delamination in a laminated specimen was investigated using unconfined and confined compression test and unsupported roof compression test. The numerical results show that, under a constant horizontal stress, delamination occurswhen the stress is much lower than its compressive strength. The confined compressive test indicates that delamination is restrained by applying confining stress since delamination-caused failure does not occur during any stage of the confined compressive test. Unsupported roof compression tests showed propagation of cutter roof failure with initiation of cracks and delamination at the intersections of the roof and ribs. An outer failed zone and inner failed zone form separately. The separated zones connect and form an opening in the roof. The presented numerical results provide additional insight into process of delamination.

Sep 14, 2020

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023

By E. L. Reed

This paper addresses the state and federal permit- ting requirements and regulatory constraints associated with the development of new "grass roots" surface coal mines in the Western United States. Since a major portion of new coal development in the West will be on federally leased coal in Wyoming, my comments are directed towards that geographical area. This will give the reader some insight into the current regulatory framework within which western mining companies must operate-i.e., the major applicable state and federal laws and regulations, the more important state and federal regulatory agencies, and the major construction and operating permits that are required. Before discussing the impact of the regulations on our business, I would like to tell you something of my company and then briefly discuss Exxon's forecast of the long range outlook for coal. Carter Mining is an Won affiliated surface coal mining company. Exxon became interested in the coal business in the mid 1960's with the recognition of the future need for alternative fuel sources. Since that time, it has acquired coal reserves located in Wyoming, Montana, North Dakota, Arkansas, Texas, Illinois and West Virginia. Carter's first surface mine, the Rawhide Mine, located north of Gillette, Wyoming began production in August, 1977. Our second surface mine, Caballo, located just south of Gillette, began operating last October. We have a third block of federally leased coal just east of Gillette. By 1985 we anticipate Carter's western surface mines will be producing at an annual rate of 30 million tons, subject, of course, to successful market development efforts and regulatory considerations. Rawhide will ultimately have a permitted capacity of 24 MM tons per year. The coal at Rawhide is in two seams; one 80 feet in thickness and the other 20 feet (including a 6 to 10 foot parting). A large shovel is used to remove the overburden, and a similar shovel and dragline are used to mine the coal. Caballo has a 75 foot seam; otherwise it is similar in design and operation to the Rawhide Mine.

Jan 1, 1979

By Kenneth Deaton

"A packaged cooling system is being developed for refuge alternatives (RAs) that will meet U.S. Mine Safety and Health Administration (MSHA) qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed refuge alternatives to be maintained by keeping the apparent temperature inside the RA from exceeding 35° C (95° F).Research investigations sponsored by the National Institute for Occupational Safety and Health (NIOSH) have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 35° C (95°F) limit established in 30 CFR 7.504.Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 27° C (81°F) mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines.The Refuge Alternative Environmental Control System (RAECS) will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96-hour refuge period.This article describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 35° C (95° F) limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature — approximately 15.5° C (60° F). The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 29° C (85° F). Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described.Expendable desiccant modules were also used to provide supplemental water vapor removal and their role in mitigating cooling load is addressed."

Dec 1, 2016

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

By G. Purcell

When coal in an oil/water slurry is ground to minus-200-mesh in a ball mill, some of the mill energy, normally wasted as heat, can be usefully recovered to help emulsify the oil. If the discharge flows onto a suitable sized trommel screen, water and ash material are rejected through the screen while coal and oil ball together to give a clean coal product. A small (6-lb/hr) continuous plant has demonstrated the feasibility and the limitations of this process for New Mexico coals.

Jan 1, 1980

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

By H. Maleki

This paper recognizes the 100th year of research accomplishments by the mining industry resulting from close cooperation among mining companies, geotechnical consultants and researchers from the former United States Bureau of Mines in stability assessments and development of improved and productive mine designs. The paper provides an overview of dramatic developments in geotechnical instrumentation, and its applications in the U.S. and around the world for enhancing the understanding of ground response to mining-induced changes in stress, resulting in improvements in ground control technologies.

Jan 1, 2010

By R. J. Pugh

In addition to directly analyzing the surfaces of minerals using high vacuum instrumentation methods, some important surface properties of mineral fillers can be determined indirectly by using reactive chemical probe molecules. This technique enables the strength and the number of the surface reactive sites to evaluation and this type of information is useful in predicting interfacial behaviour of minerals. One method of classifying these surface sites is by using Lewis acid/base theory and this type of approach could enable one to predict the adsorption of functional groups in dispersants, thickeners, pigments, etc. Also the adhesion of polymer matrices to the filler surface may be improved.

Jan 1, 1992

By R. L. Zick

The High Density Sludge Process was originally developed by Bethlehem Steel Corporation for use on acid mine drainage and diluted waste pickle liquor discharges requiring continuous chemical treatment systems. This work began in the early 1970s and was first put into practical use around 1973. To date there are approximately 15 operating systems which have been installed on mine drainage in the United States, and another 10 systems worldwide. Dense Sludge is an innovative and improved method for treating acidic metal bearing streams in a manner which minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge recycle process which forms particles that have a low affinity for water, unlike conventional metal hydroxide solids which contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations which combine with calcium ions in lime based treatment systems to form gypsum crystals. The physical form of this gypsum is radically altered when the Dense Sludge process is utilized compared to the form generated in conventional lime treatment systems. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. Slides No. 1 and No.2 show scanning electron micrographs of conventional and densified sludges illustrating these differences. The magnification used was 300X. The dense sludge particles settle faster, dewater more readily, are more easily pumped, and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered.

Jan 1, 1998

By J. Stawovy, A. Fourie, J. D. Quaranta

Coal refuse impoundments are disposal facilities specifically designed for the coal mining industry. Re-purposing refuse impoundments for co-disposal with natural gas flowback water and waste rock overburden has been investigated. The aims of this study were to investigate properties of coal refuse classification under the influence of co-disposed wastes as geochemical material exposure pathways from hydraulically exposed sodium and calcium ( Na+, Ca2+) cation loading from disposal of flowback water produced during the development of horizontal drilled natural shale gas frack wells, and waste rock having limestone characteristics. The geotechnical index classification of saturated cohesionless refuse is required to evaluate the liquefaction potential for strain or strength loss contributing to ground movements. This study is relevant to identifying changes in the coal refuse geotechnical index classification as sand-like, clay-like, or a borderline transitional material from the effects of ion and waste exposure in the impoundment’s reservoir porewater. Laboratory geotechnical tests were performed on fine coal refuse blended with different cations to classify the altered plastic behavior and index classification. Following determination of the index classification, the specimen’s stress–strain responses were investigated through isotropically consolidated undrained (ICU) triaxial compression tests. This experimental study culminated with two salient findings: the first is that introduction of ions alone into the refuse tailings or impoundment porewater resulted in significant material changes in property index classification, and the second finding was that the difference in refuse index classification did not correlate into noticeable effects of the monotonic undrained triaxial strength parameters.

Jul 5, 2022

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

A parametric study was conducted to establish the optimum operating conditions for the column flotation of fine coal. The parameters examined in this investigation included collector and frother dosages, feed solids content, and the volumetric flow rates of feed slurry, air and wash water. Despite the wide range of conditions studied the experimental data were found to fall along single grade-recovery curves, just below the maximum separation predicted by the release analysis technique. The deviation of the parametric test data from the release curve was attributed to the nonselective entrainment of mineral matter associated with poor froth washing. The operating point on the characteristic recovery-grade curve was found to be primarily determined by feed rate and aeration rate.

Jan 1, 1992