Search Documents

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

By H. Akgun

Design of plugs for abandonment of boreholes and shafts may be governed by the bond strength between the plug and host rock. This paper presents the results of push-out tests on cement grout plugs in salt. Two expandable cement grouts have been tested. The average interface shear strengths ranged from 2 to 12 MPa. Peak shear stresses at failure, assuming an elastic stress distribution along the interface, were up to eight times higher. Standard deviations commonly reached 20%. Dissolution along the interface was observed, and may have been enhanced by clay inclusions in the salt. This dissolution appears to have reduced bond strengths. Application of the results to the design of plugs for larger openings (e.g. shafts, drifts, or boreholes) is discussed.

Jan 1, 1991

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By S. Rukhaiyar, M. Ramulu, G. Pradeep, P. K. Singh, P. B. Choudhury

The drill and blast method is the most prominent rock excavation method used in mining and civil engineering projects. The ground vibration is the most undesirable effect of the blasting and needs to be controlled. The blasts are designed so that ground vibration at nearby structures must remain under the prescribed limit. Various empirical blast vibration attenuation models have been presented to estimate the ground vibration for designing purposes. These models assume ground vibration as a function of distance and maximum charge per delay. United States Bureau of Mines (USBM) model is most commonly used for the blast design. However, the uncertainty associated with these models is seldom characterized, thus diminishing its reliability. The probabilistic Bayesian approach associated with the Monte Carlo method can easily quantify uncertainties associated with the model and its parameters. Thirty-three blast vibration observation data from a granite quarry in Kerala, India, is used to estimate the probability distribution of model parameters. Markov Chain Monte Carlo (MCMC) approach is used for sampling 12,000 samples for obtaining the posterior distribution of parameters. The uncertainty associated with model parameters is quantified from the posterior distribution, and this is further used to estimate the credible and prediction limits of the model. The point estimate of the most optimum value of the parameter is estimated using maximum-aposteriori or MAP estimate. The model parameters are also obtained using the commonly used least-square error method, which is a maximum likelihood estimation or MLE approach. It has been observed that the accuracy of the model obtained using both MAP and MLE approach is almost equal. However, the MAP estimate as per Bayesian probabilistic analysis has the added advantage that it can estimate the uncertainty of parameters as well as the model, which is not possible using the MLE approach.

Sep 27, 2021

By B. Kolonja

A SIMAN and CINEMA PC-based simulation model was developed to simulate and animate the truck-shovel operations of surface mines. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. The statistical analyses were performed and appropriate theoretical distributions were fitted for various time events in the truck-shovel work cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an 'optimal" dispatching strategy to produce an equilibrium between "the quality and quantity of production.

Jan 1, 1993

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By R. L. Grayson

Compliance standards for respirable dust which are reduced because of high quartz concentrations have become an industry-wide problem. Research on the physical and chemical character of quartz-classified particles in respirable coal mine dusts indicates that they may exist in intermixed layers or may be coated by clay or coal material. The relative amount of intermixing varies with the coal seam being mined. If most of the quartz particles of a mine dust are "pure," then the dust may have a high fibrogenic risk potential because of truly free silica and the compliance standard should be lowered. If, however, the quartz is locked inside another material matrix, or coated, a reduced compliance standard may not be appropriate.

Jan 1, 1990

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By Rees D. Groves

Cement copper is ordinarily converted to marketable metal by processing in a conventional smelter and refinery. Because of rapidly increasing cement copper production and limited excess smelting capacity, other techniques were investigated for preparing marketable copper products. One route was to make copper powder for industrial use. The process scheme employed flotation for rejecting the bulk of the impurities, acid leaching to remove residual iron and aluminum, reduction sintering to eliminate oxygen, and grinding to obtain powder. Another route was to sinter the floated and leached copper into the form of anodes and electrolyze these to yield refined copper cathodes. At a current density of 30 amperes per square foot, power consumption for electrorefining was 185 kwhr per ton of copper. The feasibility of preparing commercial-size anodes by sintering is still to be assessed.

Jan 1, 1970

"What is your assessment of the minerals business?My experience with mining has been primarily in the coal sector until about 10 years ago, when I also became heavily involved in the aggregates and industrial minerals sectors. I have also had peripheral involvement through family and partners in the gold sector, with just enough exposure to gold to become fascinated. In 1994, I visited Ghana and considered the possibility of taking an expat assignment at a surface gold mine that had just been started.It is not news that the coal sector in this country has suffered tremendously in recent years. Especially hard hit is the central Appalachian region, where a number of factors combined have had a devastating effect on production, jobs and the economy. These factors include federal regulations affecting coal production and use, higher production costs and decreasing market share of Appalachian coal by the switch from lower sulfur coal in favor of lowercost, higher sulfur coal from the Illinois Basin, as utilities have installed scrubbers to comply with Phase II of the 1990 Clean Air Act Amendments. Nationally, the lower cost of natural gas has been a huge factor affecting coal use. In Kentucky, for example, which exports to other states around 70 percent of its coal, those markets are disappearing, as utilities close coal units in favor of natural gas. This is a structural change in the electricity market, and one that will become more pronounced as federal greenhouse gas regulations are implemented.We often hear the phrase, "the war on coal." While there are certainly a number of market factors affecting coal production and use, this phrase captures a different element that is all too real. The attacks have come from environmental activist groups for many years; from some in the media and, in the last few years, from a White House administration that believes strongly in alternatives to coal. Then, there really is an alternative to coal in the form of the previously untapped unconventional gas reserves that allowed utilities to move away from coal.Coal mining will continue in this country. In fact, it appears that our production is holding fairly steady at about a billion tons a year. And predictions that I have seen indicate this will continue for the next few years. What impact the Environmental Protection Agency’s Clean Power Plan will have beyond 2020 is another question.What do you feel is the future of the minerals industry - near term and longer term?Our society depends on the future of minerals in this country being strong. Near term, we are going through some of the typical cycles. Having also been involved in aggregates during the last few years, the business follows government infrastructure projects, such as highway construction and public and private sector development. Those sectors are heavily dependent upon government spending and a strong economy. Increased spending in those sectors, which appears to be on the horizon, should provide additional market shares for aggregates."

Jan 1, 2014

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By G. H. K. Pearse

Long range transport of pollutants, particularly of sulphur dioxide and the associated acidic precipitation, has received much attention in the press and in international discussion during the last few years. Studies revealing increasing acidity of lakes and the dying out of fish populations over broad regions of the eastern half of North America have created alarm. In this paper, I will not attempt a description of the acid rain phenomenon. For this r recommend the balanced treatment of the subject by Gene Likens et al (1979) in Scientific Americana For my purposes I accept that the problem is serious and direct my attention to exploring a solution. Ultimately, the key lies in the answer to the question; "What do we do with the enormous tonnages of pollution abatement byproducts, chiefly sulphur compounds, that would arise from pollution control?"' Little thought has been given to this most limiting factor to environmental clean-up. This is symptomatic of a basic flaw in the [philosphy] that under-ins environmental policy. Although this paper is to propose a solution to the abatement byproduct problem, the basic flaw - the firmly entrenched, universally adopted, 'polluter pays [philosphy] as it is currently [understood] - needs some comment.

Jan 1, 1981

By James M. Link

The first rule of mineral deposits always seems to be: the deposit is never close to the market. With gems and precious metals, this is not much of a problem. But with most of the mineral commodities used in today's world, transportation becomes a major part of the cost to the consumer. In Japan, for example, more than 60% of the cost of coal to the consumer may be attributed to transportation. The purpose of this article is to examine pipeline transportation, particularly mineral slurry pipelines, as a means of getting the mineral to market. Pipelines Today Regulated pipelines in the US totaled nearly 724 Mm (450,000 miles) in 1980 according to the Federal Energy Regulatory Commission (FERC). Worldwide, more than 210 Mm (125,000 miles) of new pipelines will start construction in 1982 at an estimated cost of more than $150 billion. According to the Bechtel Corp., the period between 1982 and 2000 will see major growth in pipelines of all kinds. In North America, major movements of crude oil from Alaska and synfuels from the Rocky Mountains will require the construction of nearly 16 Mm (10,000 miles) of new pipelines. Nearly 42 Mm (26,000 miles) of new gas transmission pipelines will be needed to tap both US and Canadian arctic gas fields and move the gas to major markets on both coasts. Other pipelines will be required to move additional quantities of natural gas from the Rocky Mountains to more populous regions. Bechtel says more than 24 Mm (15,000 miles) of slurry pipelines will be needed to transport coal from both eastern and western coal provinces to the Mississippi valley and coastal areas. In 1980, 125 companies delivered more than 1 km3 (6.5 billion bbl) of crude oil and 652 hm3 (4.1 billion bl) of products in the US. At the same time natural gas pipelines transported 498 km3 (17.6 trillion cu ft). The reported investment by these companies was nearly $20 billion at the end of 1980. Advantages of Pipeline Transportation The obvious success and vitality of the oil and gas pipeline industry is based, at least in part, on the fact that pipelines are a very efficient and low-cost method of transportation. This fact, coupled with the need for lower cost trans¬portation, has led to the marriage of oil and gas transmission technology and the bulk mineral solids transportation industry. The off-spring of this marriage is the mineral slurry pipeline. Slurry pipelines have a number of advantages over other transportation methods. One of these is the fact that they are buried-out-of-sight, out-of-mind. Second, they are relatively small users of labor because they lend themselves to automation and remote, or even computer control. Third, they offer an attractive economic alternative to other transportation systems. For example, for a 1000 km (621 miles) distance, rail costs of 1?/ km (1.7?/ton-mile) are about equivalent to slurry pipeline costs. But, as the distance increases, pipeline cost per t-km continues to drop while equivalent rail charges remain essentially insensitive to distance. Where existing rail, barge, or ocean ships are available, the cost of new construction associated with a slurry pipeline probably will render it noncompetitive. However, where new rail or other construction is needed, the cost of a slurry pipeline is very competitive. About three-fourths of the cost of a pipeline is in pipe, fittings, and construction. Nearly a fifth of the investment is in pump stations and the remainder is in right-of-way, surface facilities, utility acquisition, communication facilities, and other support areas. The fact that pipelines are capital intensive is, at the present time, a mixed blessing. For example, the delivered cost of coal in a hypothetical project doubles when the cost of money rises from 9% to 17.5% per year. The largest cost element for delivered coal in this example is in depreciation and finance charges. The next largest cost element is electricity to power the pumps, with labor making up the smallest increment of the delivered cost of coal. World Slurry Pipelines The idea of a slurry pipeline was probably first investigated in the latter 19th century, but the first ones were successfully built and operated in the US in the early 1900s. Today, they are fairly common worldwide. Table 1 shows a number of the world's slurry pipelines. An examination of these will further emphasize the fact that pipelines provide a cost competitive alternative where new construction of a transportation system is required. In each of the examples, the desired mineral commodity is located in a remote corner of the world, markets are at a great distance, value of the commodity is not great, and no other transport system is available.

Jan 10, 1982

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By Behrooz Abbasi, Seyedsaeid Ahmadvand, Thom Seal, Babak Azarfar, Bryan Ulrich

Hydro-Jex® is a new enhanced method for heap leach treatment with significantly higher mineral recovery. In this case study at the Los Filos Mine in Mexico, the Hydro-Jex operation is evaluated for heap leach stability. This is pursued by numerical modeling of the heap leach pad stability and well monitoring of the phreatic surface before and after the Hydro-Jex operation. Experimental and numerical results both indicate an improvement in mineral processing under the influence of Hydro-Jex. Numerical results show an insignificant decrease and a significant increase in stability during and after Hydro-Jex injection application, respectively. The integrity of the liner is maintained in both cases. The zonal injection pressure, operationally below the overburden pressure, is found to be negligible compared with the dimensionality of the heap, and stability of the structure is not exposed to any significant risk, even up to 25%above overburden pressure. Furthermore, heap leach factor of safety increases after Hydro-Jex application. This is attributed to breakdown of the water solution build-up and thus a decrease in the phreatic surface depth below the top of the pad. It is suggested that injection wells be drilled, based on thorough geophysical data, in locations where overcompaction of heap material results in water solution build-up and pore pressure enhancement. Compared with traditional heap leaching, the Hydro-Jex technique not only expedites mineral processing by increasing chemical kinetics extraction but also increases the stability of the heap by unclogging drains.

Jun 29, 2020

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

A comprehensive understanding of the effects of autoclave configuration (batch, semi-batch, continuous) on the residence time necessary to achieve a target conversion is a prerequisite for design of commercial scale autoclaves. Particle size distribution, mineral and reagent concentrations, temperature and mixing also influence the conversion. This paper outlines the bases of using test data to predict performance of commercial scale autoclaves. Recommendations for coordinating test program design with selection of scale-up method are provided. Examples are given to illustrate the different levels of engineering effort needed to meet corresponding levels of design optimization and accuracy.

Jan 1, 1998

By Dong Yang, Jicai Han, Xiaoshuang Guo, Tichang Sun, Zhengyao Li

Straw charcoal was used as a novel reductant in the co-reduction roasting of laterite ore and red mud. The influence of the reductant dosages, co-reduction temperature, and co-reduction time were investigated. Results showed that a powdered ferronickel product of 1.81wt.% nickel and 81.40wt.% iron was obtained under straw charcoal dosage of 15wt.% and roasted at 1250 °C for 80 min. The corresponding recovery of nickel and total iron were 97.21wt.% and 98.87wt.%, respectively. The performance of straw charcoal was also compared to that by the conventional coke reductant. Results showed that ferronickel particles using straw charcoal were larger in size than coke, mainly due to the lower S (0.14wt.%) and ash content (3.80wt.%), which could not hinder the agglomeration of the ferronickel grains, and lower melting point that producing liquid phase and promoting ferronickel particles growth. In addition, the gasification reactivity of straw charcoal is better than that of coke, which is beneficial to the iron oxide reduction and the recovery of iron. To conclude, straw charcoal is a promising reductant for the co-reduction of laterite ore and red mud in coal-deficient areas.

Aug 12, 2021

The Cutoff grade optimization is very critical to the open pit production scheduling. In case of single mineral deposits, algorithms have been developed for determining cutoff grade policy that maximizes the net present value (NPV) of yearly cash flows. For deter-mining the cutoff grade policy for projects with two minerals including stockpiles the problem becomes much more complex. The purpose of this paper is to present fundamentals of a generalized cutoff grade optimization algorithm that will maximize the NPV of a project subject to mining, milling, and marketing constraints. Benefits of the methodology developed are demonstrated on three different case studies.

Jan 1, 1997