Search Documents

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

The vast coal resources of North Slope, Alaska can be expected to attract substantial interest because the nearly flat lying coal beds of the coastal plan are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large scale coal mining and reclamation operations have not been carried out in the arctic The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the interrelationship between the problems due to permafrost and factors in reclamation of post mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1986

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By J. A. Mejia

The combination of high-resolution X-ray microtomography (HRXMT) image analysis and Lattice-Boltzmann Method (LBM) simulations has demonstrated the ability to describe real multiphase flow problems in fine coal filtration. The single component multiphase flow He-Chen-Zhang LBM model was used to simulate filtration with actual HRXMT images of pore network structures produced in filtration experiments. The analysis performed on coal, silica, and glass bead filter cakes showed that particle shape and wettability are two of the most important factors in the retention of moisture during filtration.

Feb 23, 2014

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Todd Grounds, William R. Reed, VASU GANGRADE, Michael Shahan, Garron Ross, Kunal Singh

Roof bolter canopy air curtains (CACs) are gaining acceptance as a respirable dust control device that can provide roof bolter operators with protection from overexposure to respirable coal mine dust. Both lab and field studies on the effectiveness of roof bolter CACs have been published. Field studies have shown the effectiveness to be variable. However, in all previous field studies, none has been conducted when the roof bolting machine operates downwind of the continuous miner (CM)—a scenario for which the CAC was designed to provide respirable dust control. This study, performed by researchers from the National Institute for Occupational Safety and Health (NIOSH), was conducted to test a CAC on a roof bolter machine operating downwind of the CM. The results of testing demonstrated that the roof bolter CAC can effectively provide respirable dust protection for roof bolter operators with dust control efficiencies ranging from 11 to 40%.

Oct 14, 2020

By P. James

"INTRODUCTION Control of target stream pH is very important in leach mining and treatment of MIW (mining influenced water). On the production side, solution acidity can impact SX (solvent extraction) effectiveness through PLS (pregnant leach solution) and raffinate pH. Many older operations and legacy mining sites generate ARD (acid rock drainage) that is too weak for profitable metal production by conventional means and faces costly wastewater treatment for mitigation and disposal. For wastewater and environmental treatment, neutralization to precipitate and remove metal contaminants to clean the wastewater is the dominant approach. Traditional lime neutralization and precipitation is most often used but results in large amounts of mixed metal sludge requiring costly disposal. Blue Planet Strategies (BPS); which focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources, has developed a new “reagentless” neutralization process. Electricity is utilized in its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform capability to controllably raise target stream pH. The method offers a simple, low-cost approach yielding cleaner treatment chemistry. It can result in less sludge generation and enables possibilities to selectively recover contaminants as potentially saleable products for new revenue generation to offset further offset treatment costs. DEMET Overview BPS’s patented electrolytic DEMET platform leverages solid scientific and chemistry foundations through its advanced design to achieve capabilities and performance not previously realized. DEMET technology combines separated compartment electrolytic cell functionality with proprietary advanced dynamic electrodes and cell configurations to achieve a variety of chemistries and processing targets.[1-6] DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and more cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells."

Jan 1, 2015

By Joseph W. Leonard

By combining statistical methods with specialized coal technology, novel and widely applicable procedures are developed which are useful for making important decisions based on coal seam structure. By analyzing such properties as ash in visual coal types of seam cross sections and by processing the ash data to 100 gram increments of coal ranging from the top to the bottom of the seam, intraseam comparisons between data populations of samples from a given seam and a reference seam can be made. Moreover, illustrations are presented for estimating the number of drill cores required to purchase a specified level of sampling accuracy together with procedures for determining the probability that different coal scan cross sections are not unlike and by inference are therefore comparable. Such comparisons can be valuable when making important, costly and long prevaling decisions involving coal exploration, mining, preparation and utilization.

Jan 1, 1969

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By Juan J. Monsalve, AMAN SONI, ALEX PFREUNDSCHUH, Nino Ripepi

Ground control failures are one of the main causes of accidents in the underground stone mining industry. Some of the fundamental tools for rockfall hazard identification are related to rock mass characterization and geotechnical discontinuity mapping. Recent technological advances in these methods are related to remote sensing techniques and point cloud processing software for automated discontinuity mapping. Remote sensing techniques, such as LiDAR and photogrammetry, generate multimillion point clouds with millimetric precision, capturing the structure of the rock mass. The automated point cloud processing tools offer alternative algorithm-based methods to characterize and map these discontinuities. However, their applicability is constrained by multiple factors such as site specific conditions of the rock mass and the parameters used within the mapping algorithms. This paper evaluates the performance of automated discontinuity extraction software compared with manual virtual discontinuity mapping. Sampling windows from laser-scanned sections in an underground limestone mine are defined and mapped using discontinuity set extractor (DSE). Results from the virtual discontinuity software are compared with manually extracted fractures from I-Site based on reviewing orientation, trace length, spacing, number of extracted discontinuities, and processing time. The analysis determined that the automated mapping algorithm was able to identify the same discontinuity sets that had been manually mapped. The automated mapping software mapped an excessive amount of smaller fractures, which caused the comparison of both mapping techniques to be unsuccessful in terms of trace length and spacing.

Mar 19, 2021

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By Göksel Hızlı, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

The carbothermic reduction of celestite is the first step in producing many strontium products. The way materials move in the rotary kiln has an essential effect on the carbothermic reduction efficiency as well as the temperature. In this study, the reduction of celestite ore and excess carbon blend in a laboratory-scale rotary kiln was investigated. In the experiments carried out at three different temperatures, the rotational speed and slope of the furnace tube were altered, and their effects on the reaction efficiency were examined. The leachability of the reduced powders and the content of the unburned coke indicated the optimal parameters for the reaction.When the speed was increased to 10 rpm, the powders weremoremobile in the stack and could react more easily with the furnace atmosphere. According to the results, celestite can be reduced by carbon at temperatures of 1000–1200 °C, at rates of between 5% and 75%. The maximumreaction yield (75%) was obtained with a slope of 2° and a rotational speed of 6 rpm at 1100 °C.

May 7, 2020

By R. M. G. Machunter

The presence of ultra-fine particles affects the separation performance of wet gravity separation equipment. Several studies have been undertaken to establish the maximum level of these particulates that can be tolerated by spiral separators and it has been found that unless the ultra-fine material is effectively processed, relatively low proportions in the ROM material combined with high feed rates can result in degradation in plant performance and/or excessive water consumption. The maximum level of particulate material in the process water has been determined by examination of separation performance of spiral separators under varying slime loading. This work has been conducted utilizing various feed sources and a robust ‘rule-of-thumb’ has been derived.

Jan 1, 2005

Using a Mark IV surface force apparatus, adsorption of dodecylamine hydrochloride on mica has been studied at pH 5.7 in the presence and absence of octanol. With amine alone, the repulsive forces between mica surfaces are reduced due to charge neutralization and attractive hydrophobic force; however, the latter is of relatively short-range with its decay length less than 2 nm. In the presence of amine and octanol, the hydrophobic force becomes more significant, its decay length being extended up to 6.5 nm. The increased hydrophobicity in the presence of octanol is attributed to the co-adsorption of the neutral surfactant with dodecylamine, which increases the packing density of hydrocarbons on the mica surface. The increased hydrophobicity due to co-adsorption is reflected in the improved floatability of silica when using octanol as an extender.

Jan 1, 1993