Search Documents

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By Alvaro Lucio

The continuous increase of the fuel oil price compelled CV3D to look for an alternative fuel. Charcoal was selected as the alternative energy source. This paper justifies its selection, describes charcoal properties, the methods for using charcoal in the pelletizing and shows the results of the in-plant tests.

Jan 1, 1982

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By Richard Snyder

Secretariat of the Coal Mining and Mining Executive Committees' of the National Safety Council (NSC) and Manager of the memberships to both Mining Sections; Senior Consulting Safety Engineer, NSC; member of several committees for consensus Standards of the American National Standards Institute (ANSI); a Certified Safety Professional (CSP) of the Board of Certified Safety Professionals of the Americas, Inc. and a chief proctor for CSP testing and certification procedures, et al. It appears that the tunneling trade is merging into its own renaissance for the decade of the 1970s', and most likely on past the year 2001. Federal interest in underground excavation, and more specifically, rapid excavation expertise has been on the upswing since the latter part of the 1960's, mainly due to the pressing national needs for more raw materials based on the rise for material goods and the projective gloom of possible power shortages. On the pure tunneling side the national needs encompass, in the mainstream of priorities, rapid transportation and water supply excavation as the two top contenders. For instance, the estimates for tunnel mileage for the period 1968-1975 are:(1) Subways---85 miles Urban Highways--- 123 miles Intercity Highways---210 miles Water Supply Routes---528 miles at a total of 946 miles of tunnels. The estimated cumulative underground excavation demand in dollar amounts for the period 1970-1989 are:(1) Construction Oriented Demand--- $35 billions Mining Oriented Demand---$34 billions (which includes the coal-oriented demand on the order of 26 billions.

Jan 1, 1997

By Connor Langford, Murray Gant, Ken Massé

For public organizations, preparing accurate project cost estimates is a critical component in capital project planning. Project delivery methods provide a structured approach to moving projects through the design and construction lifecycle, and typically use cost estimates as key inputs at each stage to determine if the project will advance. As design stages can occur years or even decades before construction contracts are awarded, estimates need to make reasonable assumptions about how the work may be executed (means and methods) as well as potential future market trends so that appropriate values for material pricing, labour costs, escalation, and owner’s costs can be included. This process is challenging enough during stable markets, as historic trends can often be misleading and require a suitable understanding of economic factors to use appropriately. When you mix in the market volatility that has been observed since 2020, developing accurate project cost estimates becomes even more challenging. In cases such as this, having a structured approach to cost estimating that includes an adequate risk-based reserves cannot be overstated as it provides the basis for ongoing project decisions. This paper explores some of the historic and more recent market trends that have impacted key aspects of project cost estimates for capital project planning. It also provides recommendations on how to develop cost estimates for infrastructure projects, with examples from Metro Vancouver, which plans for and delivers regional-scale services to 2.6 million residents. A brief commentary on the use of escalation clauses in contracts is also presented.

Jun 13, 2023

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By Hubert E. Risser

At the outset of a discussion on the adaptability of Illinois coals for use in iron and steel production, it is perhaps well to define terms. ?Adaptability? as used in this context, means that a coal can be, adapted to use within a given technological and economic framework. For a coal to be adaptable, to use in the manufacture of metallurgical coke within the present technological and economic framework, it must possess, among other things, at least the following characteristics: 1. The coal must be capable of producing, alone or in combination with other coals, a coke that can meet at least a minimum standard of required performance in the present-day blast furnace. The coke must have sufficient strength, stability, hardness, and freedom from impurities to make it suitable. 2. If the coal in its raw form does not meet these requirements, it must be amenable to beneficiation or upgrading so that the requirements can be met. 3. It must be available in uniform quality and in sufficient quantities to meet the need. 4. Use of the coal must be economically attractive. If its quality is equivalent; to that of the coals with which it must compete, it must be no more expensive than they. If It is better, a premium price may perhaps be demanded. If, in any respect, it is the least bit less suitable, the cost must be lower to offset its disadvantages.

Jan 1, 1961

By D. M. S. Bhatia

Five sulfide minerals from the Magiwnt mine, southeast Missouri were analyzed for 31 trace elements in over 300 samples by laser microprobe spectrographic analysis of polished sections. The concentration of several trace elements shows a pattern of progressive variation with depth (space) and variation with different paragenetic stages (time) of each mineral. Factor analysis of the geochemical data shows sympathetic correlation both in space and in time of Bi, Cd, Ge, and Sn in galena and sphalerite, and Ni and Co in sphalerite and marcasite.

Jan 1, 1979

By J. W. Wilson

In the ultrafine coal cleaning process, small coal particles (-400 mesh) are produced during the pulverizing operation. After the coal cleaning process, these ultrafine particles are very difficult to dewater, and create problems in coal transportation, storage and handling at utility plants. Research work on ultrafine coal dewatering and briquetting has resulted in the development of a single stage operation that is potentially more effective and economic than conventional thermal drying and briquetting processes. The final coal product have a moisture content of less than 15% and possess high strength and water resistance that satisfies coal transportation, storage and handling requirements.

Jan 1, 1995

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By J. G. Craig

This paper initially was to be on the design, construction and operation of the Lucky Friday mill. However, this subject has been pretty well covered in some of the mining publications in the past few years - specifically Mining Congress Journal for April, 1961 and Mining World for March, 1962- : In order to avoid too much repetition, we decided to present in this paper a comparison of the Lucky Friday mill constructed in 1959, and the Mayflower mill built by us in 1962. During the past three years Hecla Mining Company has constructed two relatively small mills: The Lucky Friday mill at Mullan, Idaho 750 T/day; and the Mayflower mill at Heber, Utah - 450 T/day. These mills were engineered, designed and constructed by Hecla, using principally our own personnel, with very little outside (contractor) labor employed. This paper presents a comparison of some of the interesting features of these mills, and where differences occur, it discusses the reasons for the various differences. It compares such points as the testing program, physical layout of the plant, construction costs, the grinding section, the flotation section, tailings disposal, metallurgy, recovery, grades, operating costs, etc. To help illustrate, and to compare these features, we will project pairs of slides showing each of the two mills. First a little background and history on the properties ---

Jan 1, 1964

By J. J. Gusek

Several final pits in the Seneca No. 1 Surface Coal Mine were abandoned in the 1960's without being reclaimed. In addition, a progressive landslide aggravated by the abandoned mine land conditions was threatening a county road and private property. An AML-funded project to stabilize the landslide and reclaim the final pits was completed in 1986 for the Colorado Division of Mines and Geology (formerly Colorado Mine Land Reclamation Division). The site was visited after ten growing seasons. The land is stable and the vegetation re-establishment is strong. Volunteer native plant species are now invading the reclaimed sites.

Jan 1, 1997

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By Terry O. Arney

This paper is a description of the digital Data Acquisition and control System that is installed at Cities Service's Pinto Valley Concentrator. Pinto Valley Concentrator ? The Pinto Valley Concentrator (5, 41 is located approximately seven miles west of the town of Miami, Arizona. The Concentrator is situated south of the open pit mine and was designed to process 40,000 tons of ore per day with an average grade of .45% copper. The comminution process consists of primary, secondary, and tertiary crushing, and single-stage closed-circuit grinding 161. Concentration of the copper sulfides is by means of froth flotation. Concentrates are transferred to the Inspiration Consolidated Copper Company smelter in Miami, Arizona through a slurry pipeline.

Jan 1, 1976

By G. Zain, Abdel-Zaher M. A. Abouzeid, Y. S. Mustafa, A. A. S. Seifelnassr

The main forces acting on minerals in conventional size reduction units are compression, impact, attrition, and/or abrasion. Usually a combination of these forces shares the breakage action of the minerals with one or more of these forces dominating the breaking action, depending on the machine used. The present work concentrates on the behavior of quartz when stressed with compression force in a confined piston die. Several size fractions within the size range minus 10 mm to plus 0.85 mm were compressed in the piston die. The measured parameters are compression load, bed thickness, displacement as a result of compression, rate of displacement, and the size distribution of the products. It was found that the size distributions are, to some extent, different from those produced by the ball mill or the high-pressure roll mill. This is mainly because of the differences in the type of the acting forces in each case. It was also found that the cumulative weight of the distributions is reasonably normalizable with respect to the median particle size of the product. The specific energy expended is inversely proportional to the median size of the products, and the reduction ratios, xf/xp, are directly proportional to the applied compression force, and hence, to the specific energy expended. A simple model is suggested for predicting the particle size distribution as a function of the expended energy. The calculated values of the size distributions match fairly well with the experimental values, except at the very low energy levels, where most of the energy expended is consumed in the rearrangement and packing of the particles in the confined space with little or no breakage.

By Osvaldo A. Bascur

Standards and Technology for bringing information at the desktop has greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure collective effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and data repository modular software are emerging in successful client server applications. The industrial desktop emerges as the new tool for continuous improvement and innovation in industrial operations. Here, process information, reliability maintenance, process simulation, production schedules, performance monitoring are integrated using Microsoft enabling tools at the desktop. A workflow model is presented to assist in implementing a strategic information system in metallurgical plants.

Jan 1, 1996

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013