Search Documents

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By Charles H. Wells

This paper describes a commercial installation of a sophisticated instrumentation and control system designed to maximize the performance of heavy medium cyclones. Samples of plant feed and its products were collected and analyzed for ash content so that measures of efficiency could be determined for plant operation under (1) manual control and (2) automatic (computer) control. The heavy medium cyclone control strategy and its digital computer implementation are discussed in detail. The sample results are analyzed and the economic benefits of automatic control are discussed. Results from the initial data sets quantify the economic benefits of automatic closed-loop control; viz, increased recovery and reduced clean coal variability have been clearly demonstrated.

Jan 1, 1981

By Richard P. Stahura

During the next five years, there will be a trend toward performing belt cleaner maintenance while the conveyor is in operation. Most mines and industrial sites that use belt conveyors have an in-house safety rule that the belt must be stopped before maintenance work can be performed on any belt-cleaning device. This is a good rule. Most cleaning devices are positioned against the belt with hardware that requires the service technician to reach or climb into the chute to change the cleaning blades. But this simple rule becomes more complicated as production demands require higher conveyor availability and provide fewer conveyor outages. In many cases, today’s conveyors are expected to be available 98% to100% of the time.

Jan 1, 1996

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By S. G. Britton

Thin seam mining presents unique challenges when management or economic conditions require significant productivity increases. These challenges are increased depending upon the presence of various external factors such as labor unions, Federal and state regulations, and market characteristics. This paper explores the turn-around situation occurring at Tanoma Mining Company (TMC), a medium-sized underground coal mining company in central Pennsylvania, USA. Using a systematic approach of improving management controls and direction, labor relations, and communications, coupled with an intensive upgrade/rebuild/replacement program for equipment and systems used at the mine, TMC has begun reversing its' cashflow position from negative to positive within two years.

Jan 1, 1991

By Doug Halbe

A number of CIP plants have been built in Western Australia in the past two years. The authors have surveyed several of these new plants and present drawings, data and discussion of operating and design innovations and areas of interest.

Jan 1, 1982

By E. Lee Bray

"Editor’s note: The editors thank those who make this annual issue possible. A special thank you goes out to the Industrial Minerals Annual Review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech Geo, is the industrial minerals annual review editor. Edgar Blanco, member SME, of Freeport- McMoRan, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• NickTushar Gupta and Sallie Gaillard, of the USGS, members SME, agricultural materials.• Abhishek Choudhuryand Xihui Yin, members SME, of Montana Tech and Kemira, repectively, ceramic and refractory materials.• Bobbi Strange and Riddhika Jain, members SME, of Outotec, Martin Marietta and Outotec, respectively, chemical raw materials.• Snehamoy Chatterjee, Alyssa Kendir and Alind Chandra, members SME, of BMT, Universityof Kentucky and Michigan Tech, respectively,construction aggregates.• Subham Verma, Gauran Soni and Freddy Sime, members SME, fillers and pigments.• Kaiwu Huang, Thomas Hilderbrand and Ricardo Santander members SME, of Virginia Tech, Thiele Kaolin and Carbo Ceramics, respectively, sorbents, filters and process aids.• Rhaghay Dubey and William Rapier, members SME, of Outotec and a consultant, respectively, specialty minerals.On behalf of ME readers, the editors thankTwo U.S. alumina refineries produced an estimated 1.5 Mt (1.65 million st) of alumina from imported bauxite in the United States in 2018. The 500-kt/a (550,000-stpy) refinery in Burnside, LA, owned by Almatis Inc. produced specialty alumina used in the abrasives, ceramics, chemical and refractory industries. The 1.2-Mt/a (1.32 million-stpy) refinery in Gramercy, LA, owned by Noranda Alumina LLC produced alumina mostly for use in aluminum smelters but also produced specialty alumina. An upgrade project at the Gramercy refinery to convert 200 kt/a (220,000 stpy) of capacity to produce more profitable specialty alumina was completed in the first half of 2018, and another project to increase capacity was started but a completion schedule was not available. The amount of new capacity was not disclosed, but it would be used to produce nonmetallurgical grade alumina. The 2.3-Mt/a (2.5 million-stpy) refinery in Point Comfort, TX, which was temporarily shut down in March 2016, remained closed throughout the year."

Jul 1, 2019

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By B. G. Hicks

The Manapouri Power Project is located in New Zealand's South Island Fiordland. The project is being constructed for the New Zealand Ministry of Works. Construction began in 1963 and is scheduled' for completion in 1969. The project will divert water from the natural, glacially carved Lake Manapouri, at Elevation 580, through vertical- penstocks into an underground powerhouse 364 feet long, 127 feet high, and 59 feet wide excavated about 700 feet below ground surface and about 560 feet below the present lake level. The possible ultimate power installation will produce 700 megawatts from turbines located in the underground machine hall. The turbine flow will discharge through the 6-mile, 30-foot diameter tailrace tunnel into a fiord arm of the Tasman Sea. The rocks in the project area are primarily Paleozoic Fiordland Complex gneiss, schist, amphibolite, and marble intruded by granitic rocks and pegmatite. Shear zones have been encountered in the tunnels and machine hall. These produce water and occasionally require steel support. The machine hall arch was stabilized entirely by rock bolt reinforcement. Rock mechanics instrumentation has been used throughout the project both for pre-construction design calculations and to monitor tunnel rock loads and movements of the machine hall roof and walls. About 28 miles of the 100-mile transmission line will be constructed across glacially oversteepened slopes and debris or swamp filled valleys between the power plant and the eastern edge of the mountainous area. Steep glacially carved rock slopes and locally unstable glacial till complicated construction of the transmission line access roads.

Jan 1, 1968

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By R. S. Conti, M. R. Krump, C. P. Lazzara Ph. D., R. L. Derick, L. L. Chasko

A mine fire is one of the most challenging safety issues facing a mine operator and can occur at any location underground. The National Institute for Occupational Safety and Health (NIOSH) and the Twentymile Coal Mine, CO, conducted in-mine experiments to determine the capability of high-expansion foam for addressing underground fires. The tests were conducted in sloping entries with high-capacity diesel-powered foam generators. The following results were observed: a well-designed, maintained and properly operated high-expansion foam generator can propagate a foam plug hundreds of feet in steep upward-sloping (20%) multiple entries against a ventilation pressure; stoppings and partitions designed to contain the foam plug in upward-sloping entries must be substantially constructed; and the predicted quantity of foam concentrate can be significantly less than the actual amount used, due to foam losses, such as bubble breakage on dry surfaces. This paper describes the production of high-expansion firefighting foam and discusses the in-mine experimental tests and results.

Jan 1, 2010

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By M Ali, E Satriawan, M Napitupulu, A Munandar

The Deep Mill Level Zone (DMLZ) panel cave mine is one of three active caving mines at PT Freeport Indonesia’s Grasberg Underground Mining Complex. The DMLZ mine is located at a depth of approximately 1,500-1800 m below the surface, making it one of the world’s deepest panel cave mining operations. This depth results in both high in-situ and induced stress that acts on the hard and massive rock mass, triggering rockburst conditions. As a result of the bursting conditions, ground support and maintaining the support capacity are an essential part of operating the DMLZ mine in an efficient and safe manner.

Apr 26, 2022

By M. P. Hoffman

The U.S. Bureau of Mines is developing a roof bolter with a computer-controlled drill head that will increase the safety of roof bolting in underground coal mines by allowing miners to be relocated to a safe area. To ensure secure anchorage, acceleration and strain data are broadcast from an instrumented drill steel to a data acquisition system. These data are analyzed, correlated, and transformed to pro-vide information about roof strata, then are sent to a supervisory computer executing National Institute of Standards and Technology's real-time control software. The supervisory computer sends setpoint commands to proportional-integral-derivative control loops to control drill thrust, position, revolutions per minute, and torque.

Jan 1, 1994

By HONGWEI YANG, Lili Zhang

The oxidation behavior of copper smelting slag under non-isothermal conditions was studied by thermal analysis. The results indicate that the copper slag is mainly composed of fayalite ( Fe2SiO4) and magnetite ( Fe3O4). The oxidation behavior can be divided into two reaction stages with the increase in temperature; the first stage is the oxidation of fayalite to magnetite, and the second stage is the oxidation of magnetite to hematite. The two reaction stages cannot be strictly separated; that is, the reaction of fayalite is not complete, and magnetite has begun to transform into hematite. Based on the TG (thermogravimetric) curves, the ABS (Achar–Brindley–Sharp–Wendworth) differential and the Coats–Redfern integral methods were employed to investigate the oxidation kinetics of copper slag during the continuous heating process. The oxidation of fayalite into magnetite and amorphous silica phases occurs mainly in the temperature range of 673 to 1083 K. The activation energies calculated by the two methods are 193.69 and 195.52 kJ mol− 1, respectively. The reaction is consistent with Avrami–Erofeev equation, and the mechanism of oxidation is random nucleation and growth. The oxidation of magnetite to hematite occurs at 1083–1303 K. The activation energies are 308.79 and 328.77 kJ mol− 1, respectively. The mechanism conforms to the Jander equation and is controlled by the two-dimensional diffusion.

May 16, 2022

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998

By T. Petrov

This study was performed to analyze the behavior of the blowing curtain face ventilation system modified with a specially designed regulator, called Wing Regulator. The purpose of the regulator is to extend the airflow penetration depth toward the face and allow effective face ventilation at curtain setback up to 13.7m (45ft) from the face. A small scale model of the Wing Regulator was successfully tested in the Mine Ventilation Laboratory at the University of Kentucky. Then a prototype of the proposed regulator was tested in full-scale in mine environment. Series of three dimensional simulations were performed to support this research using validated CFD code. This paper presents results of the performed studies and discuses the advantages of using the Wing Regulator. Presented information relates to the US Provisional Patent Application No 61/818,112.

Feb 23, 2014

By I. S. Parrish

This article offers one of the infrequent looks at Chinese mining. It includes a brief review by Parrish of a tungsten symposium held there and his comments on and impressions of the mines he visited. In early Oct. 1981, a Symposium on the Geology of Tungsten was held in the Peoples Republic of China. There were approximately 100 participants. Half of them were Chinese. The remainder included representatives of the United Nations, geologists from other nations in Southeast Asia, and 10 invited specialists from other countries. The invited guests included K.F.G. Hosking of the Camborne School of Mines, United Kingdom; C.S. Hutchinson of the University of Malaysia; K. Mattson of LKAB Int. AB, Sweden; T. Kwak of Latrobe University, Australia; K. Sato and S. Ishihara of the Geological Survey of Japan; M. Clarke of the Department of Mineral Resources, Indonesia; P. Bateman of the US Geological Survey; and the author. R. Horsnail of Amax was also invited but was unable to attend because of delayed visa clearance. The meeting was noteworthy because the Chinese were presenting more than half the papers. In addition, following the formal session, everyone was taken to the famed Jiangxi tungsten district and toured four mines there. Organization and Background The idea for a symposium on tungsten geology was brought up in late 1979 during a visit to China by the Economic and Social Commission for Asia and the Pacific (ESCAP) and, in particular, by members of the Regional Mineral Resources Development Centre (RMRDC) of the United Nations. Discussions continued and in the spring of 1981 invitations were sent to selected geologists throughout the world. China's Ministry of Geology handled arrangements, scheduling, and logistics. Travel to China and all correspondence before the symposium were coordinated by the Bandung, Indonesia Bureau of RMRDC. All costs in China were met by the Peoples Republic of China. Airfares and "per diem" enroute for participants were paid by respective governments, sponsors, or individuals. On Oct. 10, visiting participants entered China from Hong Kong. The author and a few others traveled by train to Guangzhou (Canton). Most of the group flew in the next day. The entire group was then taken to Nanchang, traveling by sleeper train and arriving on Oct. 11. The symposium group stayed at the Kiangsi Hotel, where the meetings were held. Meetings Oct. 11 was a day of orientation and rest. The group was taken to an art museum and treated to a Chinese opera movie. The formal meetings began on Monday, Oct. 12. Simultaneous translations aided presentations, though more than half the Chinese speakers delivered their talks in English. The acoustics and sound system were excellent, and the Chinese provided 35-mm and overhead projectors. There was no screen, however, and the yellow, painted wall that was used detracted from projection clarity. In general, the Chinese papers were detailed, thoughtful, and professional. Some, naturally, were stronger than others. Taking them as a unit, one derives the following sequence to the Chinese approach to tungsten exploration: (1) Geologic investigations with mapping at a scale of 1:200,000 accompanied by only minor geochemical or geophysical work. (2) Geophysical investigation with regional gravity and magnetic surveys directed toward identifying deep, tectonic systems and seeking granites in thick, crustal environments. (3) Geochemical sampling in-

Jan 6, 1982