Search Documents

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004

By M. S. Klima, V. Choudhry

Coal gasification solid residue (slag) contains unconverted carbon (char) which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal -3.4 mm gasifier slag (~85% ash) to separate high (~100%) ash slag from low (~50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71% was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1 mm in size.

Feb 24, 1997

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By J. Kallioinen

The development of mechanical flotation cells has resulted in larger and better cells. This has led to flotation banks with only a few units, even in large-scale operations. This equipment development makes the old operational considerations ineffective. The flotation cell must be considered as a single reactor unit capable of handling specific tasks and getting excellent metallurgical performance. The result of the unit reactor concept development was the new large TankCell that comes in sizes up to 113 m3 (4,000 cu ft). The TankCell construction includes new modified rotor-stator designs, new tank geometries and a froth-handling capability independent from subprocesses taking place in the pulp (i.e., air addition). The conventional idea of a single flotation cell type for fine, intermediate and coarse materials does not give optimal results. Optimal flotation of coarse and fine particles needs different mechanism designs, impeller tip speeds and different froth control objectives.

Jan 1, 1995

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By Michelle L. Ramos

INTRODUCTION The Ballard Siphon was built in 1935 and consists of two 91.4 cm (36-inch) diameter wood-stave pipes. These pipes convey sewer flowsunder the Ship Canal from northwest Seattle and the Ballard Regulator to the North Interceptor and the West Point Treatment plant. The siphons were constructed using open cut construction, are now buried in the sediment on the floor of the canal, and have severely limited ability to be dewatered, inspected, or cleaned. The existing siphon is 394.7 m (1,295 feet) long from the junction structure on the southern shoreline to the regulator structure on the north. The location of the Ballard Siphon is shown in Figures 1 and 2. The area around the Ballard Siphon has become more populated and developed since the siphon was built. Additionally, the Ballard Siphon is subject to high flows that are greater than the capacity of the pipelines. This has resulted in predict-able Combined Sewer Overflows(CSO?s) whenever a large, long duration rain event occurs. The aged pipeline of uncertain viability has become a critical piece of the sewer system infrastructure. Because of the age of the pipelines and their importance, a sonar survey was completed on both barrels of the Ballard Siphon in December of 2005. The sonar images appeared to indicate crown intrusion of the wood-stave pipes, which suggested that the pipes were in imminent danger of collapse. As a result, an Emergency Declaration was executed by King County and the Ballard Siphon Replacement Project was initiated. Staheli Trenchless Consultants was retained to perform feasibility studies to deter-mine the viability of using microtunneling and horizontal directional drilling (HDD) for replacement of the Ballard Siphon. For the evaluations, the preferred site location was determined to be at or near the site of the existing Ballard Siphon in order to minimize the ancillary sewer work which would accompany moving to a new site. To meet flow demands and hydraulic requirements, the replacement siphon needed a mini-mum equivalent diameter of 182.9 cm (72 inches). This could be accomplished with a number of different siphon diameters and configurations including, but not limited to, three 106.7 cm (42-inch) diameter pipelines, two 152.4 cm (60-inch) pipelines, or two 91.44 cm (36-inch) pipelines and a 121.9 cm (48-inch) pipeline.

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By K. Short

Today?s modern mining operations have literally dozens of applications and systems generating data whose information very often, are not crossed or centralized for operational decisions. In remote locations, the information and situation awareness is typically limited to the location itself. In addition, access to that information is limited to a small, select group of personnel that have received training on how to interpret the results. When the situation affects another area of the mine then information is relayed to the applicable areas involved. Few workers have time to analyze the situation thoroughly, to see how it affects the mines symbiotic relationship within all areas of production. If the capability to correlate and measure events and situations that affect your overall key performance indicators are not in place, the opportunity to identify process improvement becomes more difficult.

Feb 27, 2013

By Robert A. Jankowski, J. Harrison Daniel, Fred N. Kissell

Introduction Longwall coal mining in the US has steadily increased since its introduction in 1960. There are now 108 systems operating. (Sprouls, 1986). Advantages of longwall mining include higher productivity, improved safety, and greater coal recovery. Respirable dust, however, is one of the more serious obstacles to realizing the full potential of longwall mining. Early in 1980, the US Bureau of Mines (USBM) initiated extensive in-house and contract research to identify and evaluate effective methods of controlling respirable dust exposure of longwall face personnel (Niewiadomski, Jankowski, and Kissell, 1981). It was found that several control procedures must be combined to assure compliance, using control techniques appropriate to the dust source. These techniques can typically be grouped into the following categories: reduction of dust generation; dilution of dust; capture or knockdown of dust; and dust avoidance. Control techniques can be divided into basic and effective dust control techniques; additional necessary controls; and optional supplementary controls. This information should allow longwall mine operators to select control methods applicable to their particular operations and to develop a dust control plan that meets Federal dust standards. Basic and effective dust control techniques There are three basic dust control techniques (Taylor and Jankowski, 1982) that should be implemented on all longwall mining operations. • A passive barrier or external water spray system design that confines shearer generated dust near the face and away from the operators. • Large quantities of water through the sprays, particularly the drum sprays, to aid in dust knockdown and prevent dust becoming airborne. • A cutting sequence that allows the shearer operators to work primarily on the intake-air side of the lead cutting drum. Shearer clearer There are some poorly designed shearer-mounted spray systems with nozzles directed upwind at the cutting and loading zone of the intake-side drum. These actually carry dust away from the face and upstream of the drum. Where, it mixes with the clean intake air (Fig. la,) and is carried out into the walkway over the shearer operators. The Bureau developed a novel shearer spray system, called the shearer clearer. It takes advantage of the air-moving capabili-

Jan 10, 1986

By Rudy Scarabelli, John R. Wagner

At one time explosives were the only economical means of rock tunnel excavation. Except in relatively long tunnels in the right rock explosives are still the cheapest means of rock excavation where they can be used. Today the most economical means of rock tunnel excavation is increasingly not the choice of the contractor. A good part of our work is for public agencies in urban areas and the public today is increasingly less tolerant of the disruption caused by our efforts. Owners in many cases have to direct their engineers to write specifications which severely restrict noise and vibration levels during construction. Sometimes specifications allow drill-and-shoot for starter tunnels only or even eliminate powder by fiat. Recent advances in the use of explosives such as sequential firing have made blasting more palatable to the public but are not enough in all situations. Thus the roadheaders on construction projects. In recent work I have seen the Alpine Miners, a Paurant Miner and the Robbins Mobile Miners used in several rock formations and now believe this type of equipment has a place in the tunnel constructor's choice of equipment. Rudy and I have not attempted to present a formula for choosing the best alternative excavation method in any given case because, of course, of the variables involved. We have simply tried to describe our experiences on a particular project and hope our observations will be of some value to tunnel constructors.

Jan 1, 1987

The National Mining Hall of Fame and Museum (NMHF&M) will celebrate its 25th anniversary on Sept. 22, 2012 when the 2012 class is inducted during a special ceremony in Las Vegas, NV in conjunction with MINExpo 2012. The NMHF&M will induct four men representing the equipment manufacturing, minerals exploration, copper and coal sectors of the mining industry. The diverse cross-section of mining industry giants joining the hall of fame include Glen A. Barton, J. David Lowell, Samuel Newhouse and John Cleveland Osgood. They will join 214 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame at the 25th Silver Anniversary Induction Banquet & Ceremony. These men were selected for being visionaries, leaders and ambassadors within their own sectors and across the industry at large.

Jan 1, 2013

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By Yoneji Kanoh, Masahiko Ohtsuka

In Japanese tunneling history, it has commonly been accepted that the long-round driving is difficult due to the complicated geological condition. Therefore, the maximum past record has been less than 3 m per round. A new record of advance was established in the 99 m2 headrace tunnel of Imaichi Water Power Station Project with an advance of 239.5 m in a month by drilling 3.9 m deep blast holes. The geology of the headrace tunnel composed of pyroxine andesite (ie. 960-1770 kg/cm2, VP3.1-4.3 km/s) which had several clay seams and open cracks and was moderately weathered. Automatic shotcrete machine was used for shotcreting. Rock support was specified according to the N.A.T.M. with each different rock type. The contractor achieved a remarkable tunneling advance not earlier experienced in Japan.

Jan 1, 1983

By Russell Barr

Strategic alignment throughout a mining organization is critical to effective strategic execution and good business performance. The alignment of strategic goals and objectives in the different operations and functions in a large global operation is a challenge facing executive management in light of legacy organizational structure and processes. An additional confounding factor in strategic alignment of acquisition and new project expansion is that mining projects and operations are frequently multi-cultural in terms of country origin as well as organizational culture. This brings together many cultures to accomplish the project or complete an acquisition (Financial Times, 2006). The mining industry presents numerous challenges to executives and mine management by the nature of the operation and organizational processes used in running it. For example, there seems to be an inherent conflict between the individual goals of the components that constitute a mineral processing operation (the mine, the mill, the smelter and the refinery), and lowest cost production of the final product. Managers of these component operations have specific objectives passed down from the corporate executives. Those site managers tend to be compensated based on throughput and perform to this main metric. This tendency to maximize throughput for an individual operation can contradict the general process flow of a best-fit solution to producing the final product at the lowest cost. In an effort to become more aligned, firms are increasingly using balanced scorecard derivatives at great cost and effort (whether internally or externally sourced) in an attempt to help with strategic alignment. Balanced score-cards have been effective in providing a good strategic scorecard to companies with some measure of strategic alignment. Many firms make this effort of using balanced scorecards. However, most firms are not strategically aligned or, at best, are sub-optimized, in terms of strategic alignment (Kaplan and Norton, 2006). The tendency in mining operations is to focus on operating individual components as optimally as possible and stretching existing assets to the best possible production rates. ?Making tons? is the common operational focus. Numerous factors underpin this focus and can affect the ability of the operation?s ability to align properly with the corporate strategy and strategic goals. Critical factors are legacy organizational structure, culture, processes and performance measurement systems. Changing anyone of these factors to affect better strategic alignment requires significant attention to managing change.

Jan 1, 2008

By Ed Cope

The newly discovered South Arturo deposit is a Carlin-type, breccia-hosted, oxide gold deposit located on the Dee Mine property at the north end of the Carlin Trend in Nevada. The Dee Gold Mine was discovered in 1981 by Dee Delamar, a Cordex geologist. The property was put into production by Rayrock Mines in 1984. During its 16-year mine life, the Dee Mine produced about 18.6 t (600,000 oz) of gold from oxide ore at an average production rate of about 1.24 to 1.55 t/a (40,000 to 50,000 oz/year). In October 1997, Bar-rick Gold Exploration acquired the right to earn a 60-percent interest in the Dee property from Dee Gold Mines through an exploration farm-out agreement. Barrick Gold Exploration began exploration activities on the property in 1998 and vested in its 60 percent operating interest in 2004. However, the discovery hole at South Arturo was not drilled until July 2005 from atop the historic mine dumps located 300 m (985 ft) south of the Dee openpit. The discovery hole (BD-72) encountered a cumulative 75.6 m (248 ft) of oxide mineralization grading 1.9 g/t (0.055 oz/st) gold beneath 260 m (855 ft) of dump material and post mineral Tertiary Carlin Formation volcanic and sedimentary rocks. Oxidation within the deposit extends to depths greater than 610 m (2,000 ft). The deposit has passed the prefeasibility test and is presently in the feasibility stage. Exploration is on-going to enhance or enlarge the known deposit. The current resource for the deposit stands at 40.4 t (1.3 million oz) of gold. The South Arturo discovery is an example of an historic mining property yielding a new discovery through the diligent application of area selection criteria of the model type and persevering when early results were generally negative. Barrick?s original exploration pro-grams on the property were focused on the discovery of deep, high-grade sulfide deposits that would likely be mined by underground methods. As it turns out, South Arturo is mostly oxidized and will be amenable to mining by openpit methods

Jan 1, 2008