Search Documents

By André Vervoort

At the 2017 ICGCM-conference in Morgantown, WV, a case study was presented with measurements of the upward surface movements or uplift after the closure of two neighboring coal mines (Winterslag and Zwartberg, Belgium). One was closed in the sixties, and the other closed in 1988. The study was based on satellite data (Radar-interferometry or InSAR). The analyses showed both a significant variation of uplift values above the mined area and the surrounding zones, and a variation of the uplift rate as a function of time. In other words, the phenomenon of uplift is complex. At that time, it also was clear that more research was needed to better understand this phenomenon, e.g., an identification of the various mechanisms that are relevant for the process of uplift and the quantification of the various impacts. A systematic analysis of all relevant parameters resulted in a framework that forms the basis for the analytical calculations of uplift values. These calculations show that the main impact is due to changes in the hydrostatic pressure. However, the expansion of the softest parts, i.e., the collapsed or goaf material, is not only important, but the expansion of the (stiffer) non-collapsed strata layers due to a change in pore pressure also must be integrated into the model. For the case study, the partial flooding of the underground after closure of the mine that was abandoned in the sixties is integrated into the model. Larger stiffness values also are applied for this mine, in comparison to the values of the more recently closed mine. Overall, a very good correlation is observed between the InSAR-measurements and the calculated values along a north-south transect.

By A. G. Mayton, L. Adler

The paper under discussion provides an excellent and concise study of compartment ergonomics for thin seam equipment. However, in accomplishing this, some very important operational aspects were ignored. Since these are likely to be determinant, the authors' response is solicited. The novel shuttle car with its cross-car, end-mounted compartment is operationally very different from the current one. The latter can be considered a highly mobile extension of the continuous miner or loader, with a pass-through conveyor, dump boom, and extra storage. As such, the vehicle's kinematics are the simple "I," or shuttle pattern, bent for going around pillars, with an intermediate stop at the "change-out point" (Adler, 1986 ). The action of the cable reel adjusts well to this pattern. The proposed shuttle car's motion either superimposes a "Y," time is lost (5 seconds) for each cycle, space is needed, line of sight is compromised, and a cable anchor is probably required at the dump. A chute is almost prohibitive in construction time and cost. The lack of a dump boom further curtails flexibility in the proposal. The value of a standard hand and opposite standard hand configuration also needs consideration. Many front-end loaders have a rocker (overshot) capability that is designed to achieve an "I” pattern. And crawler loaders sometimes use a side dumping bucket variant for the same purpose. These examples indicate the pattern's importance. For underground, thin seam application, the ram car has become popular. This is an articulated truck, battery-powered, and with an ejector dump. Its operational patterns would be similar to the novel shuttle car, except without the loading flexibility provided by a conveyor. Since the cab location of the proposed shuttle car largely obviates some of the major advantages of the present shuttle car, the question arises whether this configuration could be adapted to the current ram car and scoop

Jan 1, 1991

By Steven T. Mitchell

The introduction of Vertical Crater Retreat (VCR) Stoping at the Homestake Mine in Lead, SD, constitutes a major advance in Homes take Mining Company's efforts to improve productivity and reduce costs through underground mine mechanization. The work to date indicates that Vertical Crater Retreat Stoping is one of the safest methods of underground hardrock mining today, and is competitive with all other forms of stoping in terms of cost and productivity. Homes take anticipates that VCR stoping rill account for approximately 30% of the total mine production in 1980.

Jan 1, 1980

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975

By G. H. Kuhnhausen

The Bear Creek Uranium Mill was designed in 1975 to process 909 tonnes per day (1000 STPD) of low-grade uranium ore from the Powder River Basin in Wyoming. The mill was expanded to 1818 tonnes per day (2000 STPD) in 1979. The Bear Creek Uranium Project is owned by the Bear Creek Uranium Company, a partnership of Rocky Mountain Energy Company and Mono Power Company. The original mill design contemplated processing ores from Bear Creek Uranium Company properties exclusively. The expanded capacity has been utilized for tolling ores from Kerr McGee Nuclear Corp. and other mining companies in the region. This paper describes the process of designing the original mill, the lessons learned from operation, and the design of the process modifications required for expansion. The project background, design philosophy, design basis, design criteria, actual flowsheet, special design considerations, and a comparison of assumed operating conditions and actual operating results will be presented. Bear Creek Uranium Company wishes to thank and acknowledge the help granted by the many operating companies who provided invaluable information, insight, and critique of the Bear Creek design through all the various stages and were instrumental in the successful completion and start-up of the mill. Without their contributions, the design philosophy used at Bear Creek would not have been possible and the results obtained would surely have been less satisfactory.

Jan 1, 1979

By P. T. Luckie

The selectivity curve -- a continuous function which predicts the expected proportion of feed material of a particular size that will appear as coarse material -- is the preferred model for describing classification. In a previous paper (I), the authors presented a technique for determining the selectivity curve of a classifier from experimental data. The separation process is defined by a binomial distribution of the form [ ] where s(x), the probability of particles of size x reporting to the coarse stream, is obviously the selectivity value for material of size x.

Jan 1, 1975

By Thomas A. Wilson

Mountain Pass, California is located 96 km southwest of Las Vegas, Nevada, and has an exposed surface orebody within view of Interstate Highway 15. Mineral prospecting in this region dates back to about 1860 followed by the discovery and subsequent mining (1870-1895) of silver bearing veins on the north slope of nearby Clark Mountain. In contrast to the four lane divided interstate highway of today, all supplies needed for mining during this early history were transported by wagons from San Bernardino which is 320 km west. Many small lead mines were active in the area during 1917-20, and a small gold mine operated in 1941-42 within 100 m of the orebody presently being worked. In 1949 two prospectors searching for uranium with a Geiger counter discovered a radioactive vein outcrop at Mountain Pass. Further investigation revealed the presence of a large amount of a light-brown, heavy mineral to a depth of about 2 m. A sample of this unidentified mineral was submitted to the Boulder City, Nevada, U.S. Bureau of Mines where a spectroscope examination shoved high level rare earth oxides, carbon dioxide, and fluorine. These results indicated the mineral was bastnasite.

Jan 1, 1982

By Joseph M. Morrison

This paper offers a comprehensive solution to the problem of dust emissions at belt conveyor transfer points. It discusses details of enclosure design and presents a straightforward procedure for calculating required dust control exhaust volumes. Many design variables are taken into account which heretofore have been commonly ignored or inadequately considered. These include belt widths, belt speeds, enclosure openings, material flow rates, material bulk densities, material lump sizes, height of material fall, material temperature, and ambient air temperature. All of these quantities are handled by means of a "fill-in-the-blanks" type of calculation form which permits quick, reliable solutions by relative "non- experts".

Jan 1, 1970

By L. Arbore

Introduction Mine operators are interested in energy conversation in two ways. With our finite sources of energy, we are concerned for future generations. In addition, as mine operators, we want to minimize energy costs. Moving material represents a substantial amount of the energy used in mining operations. Wheeled vehicles are used extensively to move materials. And they derive all their energy from fuel. Energy is also required to overcome the vehicle's inertia, and internal and external frictional forces. Included in the vehicle's frictional forces is its suspension. Tires are an important part of this suspension. What influence do tires have on the overall fuel consumption of the vehicle? Does tire construction affect this influence? As far back as 1896, it was apparent that tires were a factor in fuel consumption. A test was devised in France using a coal-fueled steam-driven auto. The test measured whether there was any fuel savings with the new pneumatic tires rather than of the then commonly used solid tires. The result was a 28% savings in water and a 29% savings in coal on pneumatic tires. Today, the pneumatic tire is accepted, but there are differences in present constructions. Tire Construction: Bias vs Radial There are basically two types of tire construction, bias and radial. Bias tires have been around for about 60 years. Radial tires are more recent. They were developed to improve a tire's ability to withstand higher speeds and loads, as well as to improve tire life and vehicle handling. Another advantage of the radial tire is its lower rolling resistance. This characteristic results in lower fuel use by a vehicle. This has been demonstrated with passenger cars and over-the-road trucks. It is now being demonstrated with earthmoving equipment. A basic description of both types of tire construction should now be reviewed: The casing of a bias-ply tire is made up of crisscrossed textile plies or layers. The cords of these plies run on a bias, from bead to bead. The cords of each ply run on an angle relative to the cords of the adjacent plies. As the tire rolls and deflects, the angle between the cords changes, like the blades on scissors (Fig. 1). The cords of one ply pull one way, and the adjacent ply pulls another, straining each other. This movement generates heat. Since the same layers of cords wrap around under the tread, they

Jan 9, 1984

By M. Dean Kleinkopf, John Callahan, William M. Shepard, R. N. Schnepfe

Despite lower prices and the uncertain future of nuclear power, uranium continued to be the big attraction in 1979 exploration activity. Uranium again dominated exploration programs across the US-not only in primary producing states such as New Mexico and Wyoming, but in potential producing areas from the northern counties of Minnesota to the Grandfather Mountain region of North Carolina. The moratorium on uranium leasing was lifted in Colorado and Montana, and exploration activity intensified accordingly. In Wyoming, what may be the biggest uranium deposit in the state was discovered by Anaconda Copper Co. near Jeffrey City, but in general, there were few major discoveries and activity was concentrated on existing exploration programs. The Department of Energy expects 1979 uranium exploration expenditures to total $339 million, compared to the $314 million spent by industry in 1978. Surface exploration and development drilling in 1979 is estimated at 16.1 Mm, up slightly from 1978 figures. Gold demanded its share of the spotlight in 1979. Soaring prices lured prospectors, investors, operators, and speculators to Alaska, California, Colorado, and Washington in a small-scale gold fever. Exploration for molybdenum remained strong in Alaska, Colorado, and Washington, where mineralization at the Mt. Tolman prospect is now estimated at 816 Mt averaging 0.09% copper and 0.10% molybdenum disulfide. Again this year, one of the major deterrents to exploration was the drive to set aside huge areas of land as wilderness preserves. In Alaska, where Interior Secretary Cecil Andrus has withdrawn millions of acres under the Antiquities Act, BP Alaska decided to close its Anchorage office, reportedly due to the lack of public lands available for mineral exploration. In both geophysical and geochemical activity, the year is best characterized as one of consolidation and development of previous advances in the state of the art, without any fundamental breakthroughs. Many companies were active in the development of instrumentation. Continuing interest in spectral IP resulted in the introduction of two instruments, one by Phoenix Geophysics, the other to be announced shortly by Geotronics Corp. Radiometric and borehole logging equipment received considerable emphasis, reflecting the continued interest in uranium exploration. MINING ENGINEERING'S review of 1979 exploration activity, including state-by-state highlights and a review of geophysical and geochemical activity, begins on the following page.

Jan 5, 1980

By Harold L. Lovell

The extensive heterogeneity of coal is a fact long recognized by scientists and engineers. However, until recent years the practical implications of such heterogeneity have more often been realized from an undesirable experience than from knowledge or forethought. Variations in the properties of coal, even within the same seam, eventually lead to procedural modifications in mining, handling, preparation and utilization. The concepts considered here propose an enhanced application of information, detailing these properties, realizing the uniqueness of any given coal seam but the practicality of a common approach. Coal preparation practice has been designed primarily for the control of ash and sulfur content to meet market specifications which are similarly specified, Other physical characteristics of size and friability are also commonly employed and, to a lesser extent, properties which are implications of rank. The consideration of petrographic data as indicators of origin, thus total physical and chemical properties, has generally been overlooked as a realistic tool in-the exploitation of coal as a resource. The evolution of descriptive techniques, whether petrographic, physical, or chemical, capable of universal application with any rank of coal, is still beset with problems.

Jan 1, 1968

By John M. Karpinski

A method and equipment have been developed Tor measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional .to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts, The results are interpreted in terms of the flaw theory of brittle fracture.

Jan 1, 1964

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By M. Misra, I. Anazia

The dispersion of oily collector has a significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. Such dispersion and reagent addition techniques are invariably inadequate and nonselective. A new collector addition technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This technique involves atomization of the collector into the air stream. Under these circumstances, an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the air phase (continuous with respect to oil), and the air phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and, most significantly, increases the flotation rate of ultrafine coal. Atomization of collector/frother combinations yielded improved flotation recovery and maintained near uniform froth levels, which is a desirable feature in coal flotation. Microscopic examinations of the attachment of oil- coated bubbles at a coal surface were conducted by attachment time and contact angle measurements. Oil-coated bubbles attach at significantly faster rates and with a higher contact angle than oil-free bubbles.

Jan 1, 1988

By Lorraine B. Yde

Successful implementation of computer systems deals with meeting final systems objectives and cost and schedule requirements, but the final success is dependent upon personal inter- action. This is a case history of the installation of responsibility reporting at The Anaconda Co.'s Twin Buttes operation, later to become Anamax. The study has been documented as it occurred in hopes that it will illuminate the "people" side of computer systems implementation. Systems implementation involves negotiating with people. "The cooperative approach to negotiation (Nierenberg, 1968) the approach which vostulates that all varties must come away having gained something is based on a simple but important premise. Negotiation takes place between human beings. You cannot negotiate with a computer." This is a look at the human side of a major system installation. An attempt is made to show how a reporting system enabled a company to take a new look at itself. It is also an example of statements made by Toffler (1970) in Future Shock. "As machines take over routine tasks and the accelerative thrust increases the amount of novelty in the environment, more and more of the energy of society (and its organizations) must turn toward the solution of non-routine problems. This requires a degree of imagination and creativity that bureaucracy, with its man-in-a-slot organization, its permanent structures, and its hierarchies, is not well-equipped to provide."

Jan 1, 1979

By S. Rideout

As Assistant Director for Program Support for the Office of Surface Mining Reclamation and Enforcement (OSM), a bureau of the U.S. Department of the Interior, I am responsible for the regulatory and abandoned mine land programs under the Surface Mining Control and Reclamation Act of 1977, which governs the environmental impacts of coal mining. My perspective is influenced by my current position and my previous positions in government and private industry. Sustainability is a cooperative effort of many parties and can only be achieved if each assumes their responsibilities for making it happen. I will highlight some of my thoughts on the role of government in achieving sustainability in the mining arena.

Jan 1, 2007

By Gerald L. Dollinger

INTRODUCTION Today more tunnels are being bored by mechanical means in igneuus and metemorphic rocks (i.e. "hard" rocks) than ever before, and there is reason to believe that this trend will continue in the future. Because of this, there is an increasing demand fur stronger, more powerful machines and fur cutters that are capable of handling the high loads and abrasive rock conditions that often accompany hard rock tunneling. Tunnel boring machines ("TM's") built today, therefure, generally have higher thrust and torque capabilities than those built in the past, and they are equipped with the largest cutters and rings now available. The recent experience in hard rock tunneling has demunstrated that TBMs can be both efficient and ecunumical under such conditions, and that acceptable performance rates can be achieved in all but the hardest rock. In spite of this success, it is believed that improvements in buth the cost of boring and in performance rates can still be made through mudificatiuns in the existing kerf cutting system. Some impruvements in TBM performance under hard rock conditions, fur example, have already been made thruugh the development of constant section rings that maintain a constant edge width and, therefore, a constant level of performance as they wear. The recent experience in hard rock tunneling has also produced a wealth of new TBM performance data through the systematic study

Jan 1, 1983

By R. J. Watters

Many rock sass classification systems exist' to assist the engineer in assessing the rock support requirements for underground design. Our ongoing research in this area is directed at attempting to utilize the fractal dimension and the acoustic emission' response of the tuffs at Yucca Mountain, Nevada to further aid in rock mass classification. The Topopah Spring' member, the proposed nuclear waste horizon, is characterized by welded and partly welded tuffs, exhibiting a wide range in moduli, strength, porosity and degree of fracturing. Differentiating between the different' types of porosity can be extremely difficult if not impossible. An attempt was made to correlate the acoustic emission response with the porosity of the sample. Events and the peak amplitude may offer a means-to distinguish between, fracture porosity and pore porosity. In addition-, fractal dimension were calculated for several fractures in densely welded tuffs. Two techniques for calculating fractal dimension were-applied' to describe-fracture geometry and roughness. Fractures in-welded-tuff were-found to be relatively smooth.

Jan 1, 1989