Search Documents

By J. Hop, A. Støre, T. Foosnæs

The carbon cathode for aluminium electrolysis is also part of the container of the process. In order to understand the behaviour and possible failure of the cathode, detailed material properties under operating conditions are needed. The paper reports experimental studies of bath and sodium in filtration, graphitization with time, loss of strength due to sodium, sodium expansion as function of pressure, as well as creep due to the developed stresses. As an example, sodium and thermal expansion data are used to calculate strain-stress models of realistic cell designs, and possible design weakness can be pointed out. Keywords: carbon, cathodes, sodium expansion, strength, graphitization, creep

Jan 1, 2004

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

By Dennis Van Heerden

Southern Africa has a long history of underground hard rock mining dating back to the late 1800?s. The rock support of underground excavations has significantly changed during this period, due to improved technology, experience gained and rock support requirements by mining and geotechnical engineers. This paper examines the available underground rock support methods in Southern Africa with emphasis on the types and characteristics of: - Rock bolt types. - Rock bolt and long anchor grouts. - Thin-sprayed liners. - Sprayed Concrete. - Ground consolidations through injection methods. - Cavity and void filling with aerated cement products. [ ]

Jan 1, 2007

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and 1580ºC under 0.03 atm, 0.05atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged to SiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S)systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermodynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on pseudo ternary SiO2–(AI2O3+CaO+MgO)–(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: Chromium, slag, equilibrium

Jan 1, 2004

One of the seminal pioneering papers in reserve evaluation was published by Danie Krige in 1951. In that paper he introduced the concept of regression techniques in providing better estimates for stope grades and correcting for what later became known as the ‘conditional bias’. In South Africa, the development of this approach led to the phenomenon being dubbed the ‘regression effect’, and regression techniques ultimately formed the basis of simple kriging in Krige’s later papers. In the late 1950s and early 1960s, Georges Matheron (1965) formulated the general theory of ‘regionalized variables’ and included copious discussion on what he termed the ‘volume-variance’ effect. Matheron defined mathematically the reason for, and quantification of, the difference in variability between estimated values and the actual unknown values. In 1983, this author published a paper that combined these two philosophies so that the ‘regression effect’ could be quantified before actual mining block values were available. In 1996 and in some earlier presentations, Krige revisited the regression effect in terms of the conditional bias and suggested two measures that might enable a practitioner of geostatistics to assess the ‘efficiency’ of the kriging estimator in any particular case. In this article, we revisit the trail from ‘regression effect’ to ‘kriging efficiency’ in conceptual terms and endeavour to explain exactly what is measured by these parameters and how to use (or abuse) them in practical cases.

Jan 1, 2015

By S. P. Pearton

"Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades, and their unique properties offer significant advantages in terms of improved safety, reliability, and performance. However, the benefits of pumpable emulsions have been unavailable to narrow-reef mining operations due to the lack of technology necessary for their successful implementation in this challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow-reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology, and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow-reef environment.The purpose of the following investigation was to evaluate the viability of pumpable emulsion explosives for use in South African narrow-reef mining operations. By approaching the problem from multiple perspectives, this research aimed firstly to propose a theoretical framework and suite of equipment suitable for the implementation of pumpable emulsions within the narrow-reef environment. Through the development of this suite of pumpable emulsion technology, tests could be undertaken on the proposed narrow-reef emulsion formulation and pumpable emulsion technology to obtain the necessary understanding of the performance of the system under controlled operating conditions prior to its implementation in the broader mining industry."

Jan 1, 2015

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By F. T. Cawood

?It is in the interest of stability and investor confidence that the healthy and necessary debate on such a (minerals) policy should soon find its way to consensus.? (President Nelson Mandela at the104th (1995), AGM of the South African Chamber of Mines) Inauguration of the new political dispensation in South Africa initiated a dynamic period in the historical development of its minerals policy. The process of substituting the current South African mineral policy framework with an acceptable ?post apartheid? system, started soon after the 1994 election of the African National Congress (ANC) government. The Green Paper on a Minerals and Mining Policy for South Africa released for public discussion in February 1998, calls for radical transformation in mineral rights ownership. A shift towards exclusive state ownership of mineral rights, away from the present dual system of private and state ownership, is the most significant proposal. The current holders of mineral rights, or their nominees, who lawfully enjoyed security of tenure under past and present mineral laws are opposed to this transformation because mineral rights were often acquired at considerable cost. The situation is compounded by poor public record-keeping and passive mineral rights administration over a very long period. This paper represents a summary of the historical developments leading to the current legislative environment and forms the basis for any discussion on which future sculpturing of South Africa?s policy regarding mineral rights can take place. One cannot plan for the future without considering the past!

Jan 1, 1998

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

By M. I. Mthenjane

"BackgroundThe paper discusses post-mining land use however, the essence of the topic is the emotional motivation behind the decisions related to mining investment and development. Therefore this is not a typical SAIMM technical paper about the science and techniques of post-mining land use. There are already numerous papers written and conferences held on this aspect of post-mine land use; the science is well understood, but the evidence of the practical application of the (environmental, social, and economic) science is sparse. At a recent conference held in November 2017 on the theme of ‘Science, Business, Society Dialogue – linking science, society, business and policy for the sustainable use of abandoned mines in the SADC region’, it was demonstrated through the delivery of several papers on the possible viable options of post-mine land use. The conference was structured in nine sessions, covering the following relevant topics:? Sessions 1 and 2: Nature and magnitude of the problem: raising awareness? Sessions 3 and 4: International experiences in remediation: case studies? Sessions 5, 6 and, 7: Technological solutions: converting liabilities into assets? Session 8: Implementing solutions: social and legal aspects? Session 9: Wrap up, lessons learned: conference resolution.Summaries of the key outcomes of the sessions are available for reference.The aim of this paper, accompanied by the video speech, is to provide a visualization of the possibilities of post-mine land use. Mining contributes approximately 7% to South Africa’s GDP - this is the lowest it has ever been and is attributable to both a diversifying economy and to poor mining and investment policy which has resulted in reduced investment in the sector. The objective of the paper is to highlight the opportunities, for succeeding and diversifying economic activity following mining and mineral extraction which can continue to sustain the livelihoods and wellbeing of communities and societies beyond mining.During mining, very few alternative and local economies develop. Dependence on mining and its value chain prevails until mining ceases. This idea is conveyed in Figures 1a and b."

Jul 1, 2019

By C. Kloppers

The aim of this investigation was to reduce the cost of primary steel de-oxidation by substitution of aluminium primary de-oxidation with a practice that uses carbon. The cost of carbon is four times lower than that of aluminium. The application of carbon would directly result in raw material cost savings. Investigations were conducted at Iscor?s Newcastle steel plant on various steel grades. Specific production aspects were emphasized to ensure that the cost savings accrued would not create secondary expenses. These production aspects entailed: ?Yields on de-oxidation elements ?De-oxidation capabilities ?Alloying yields (Mn and Si) ?Carbon-pickup ?Nitrogen-pickup ?Temperature loss during tap ?Steel cleanliness ?Slag morphology. This project proved that carbon de-oxidation, apart from reducing de-oxidation raw material cost due to cheaper raw materials being used and lower consumption rates, resulted in steel that is cleaner and has lower nitrogen concentrations. Carbon primary de-oxidation has been implemented at Iscor?s Newcastle plant on a large range of steel grades, ranging from ultra-high carbon (> 0.60% C) to ultra-low carbon (< 0.03% C) grades. A net saving of between R100 000 and R200 000 per month was achieved.

Jan 1, 2001

By P. C. Schutte

The objective of ergonomics is to enhance the effectiveness and efficiency with which human tasks are carried out. Furthermore, the objective is to improve desirable human values. This can be achieved by enhancing safety, reducing fatigue and stress, increasing comfort, increasing job satisfaction, having greater user acceptance and thereby improving the quality of life. Mechanization has influenced the prevalence of injury, mainly due to the application of human physical effort as the power source. With mechanization, the operator?s function is now essentially one of control rather than being an energy source, however, the risk of injury has not diminished. Mechanization in itself has introduced inefficiencies, health risks and physiological stress. The major objectives of ergonomics are discussed through examples of acceptable and less successful implementation of ergonomics within mechanized mining. The influence of the machine system on the human is addressed and practical solutions to improve and optimize the interaction of the human and the machine are outlined. Furthermore, practical examples of control and display integration, anthropometric and biomechanic influences on design, orientation, posture and stereotypes are used to accentuate the advantages of the application of sound ergonomics principles to the specialized area of mechanized mining.

Jan 1, 2002

By C. Musingwini

The Bushveld Complex is economically significant and strategically important to South Africa, thus it is imperative that optimal extraction of platinum group metal (PGM) resources on the Bushveld Complex is achieved. Optimal extraction broadly requires that the maximum amount of ore is extracted by excavating and hauling the minimum amount of waste in the shortest possible time, at the least cost, and in the safest and most environmentally acceptable manner. In open-pit mine planning this entails among other things, minimizing the waste stripping ratio, whereas in underground mine planning it includes minimizing the metres of waste development. In conventional mining, the main development that is in waste or partly in waste and defines the mining grid pattern includes levels and raises. It was prudent to consider optimizing level and raise spacing in conventional mining because the method is a prevalent mining method on the Bushveld Complex accounting for nearly 70% of platinum production.

Jan 1, 2010

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

Resolution Copper Mine is planned to be a 2000 m deep panel cave mine with virgin rock temperatures above 80°C in rock with a high crystalline silica content. The planned run-of-mine production rate is 120 kt/day. The project is in prefeasibility evaluation. This paper discusses features of the ventilation system design, which include multiple ventilation shafts with total flow of about 3000 m³/s and both surface and underground refrigeration systems with more than 140 MW total capacity. This will be a very challenging mine to ventilate, but this work has demonstrated that it will be technically achievable with the application of existing technology.

Jan 1, 2014