Search Documents

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By A. L. Murray

"Welfare endeavor in connection with both the metal and the coal mines of Utah has shown gratifying progress during recent years, and in most mining towns of the state, both the operators and their employees deserve much credit for the efforts put forth to better the living, working, educational and recreational conditions. Progress has been and is being made, but there are still a few important towns where purer water and better sewage disposal are pressing needs.In the older metal-mining towns that are incorporated and are independent of the mining properties operating in the vicinity, less opportunity is presented for the companies to exercise efforts looking toward improved welfare conditions than in company towns controlled by the mine operators.However, even in such towns the companies can do much to better welfare conditions, as shown by the progress in Bingham Canyon during the past several years. The Utah Copper Company has spent $800,000 since 1920, in the erection of modern brick cottages, apartment houses and the Germnell Memorial Club. The cottages and apartment houses have every convenience to be found in up-to-date city homes. The Gemmell Memorial Club erected and equipped at a cost of $175,000 was provided by the company for the benefit of the Utah Copper employees living in the canyon and has been made the recreational center for the camp. Another improvement is the $100,000 fireproof hotel built by the United States Mine of the United States Mining, Smelting and Refining; Co. in the Copperfield section of Bingham Canyon. This hotel will accommodate 105 men exclusive of hotel help and has all the conveniences of a city hotel."

Sep 1, 1925

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By Steven J. Page, John A. Organiscak

Airborne dust generation is one of the byproducts of coal mining, processing, and handling. The amount of airborne total dust (ATD, respirable size and larger) and airborne respirable dust (ARD) generated is of primary interest for designing the level of engineering controls needed for adequate dust abatement. Laboratory crushing experiments were conducted in a wind tunnel with a roll crusher to identify relationships among crushing parameters, product size, coal rank properties, and airborne dust generation. Through the first series of experiments, the effect of primary and secondary breakage processes on both product size and airborne dust generation was examined. Through a second series of experiments, the effect of coal rank properties on product size and airborne dust generation was studied using a uniform crushing process with secondary breakage. Laboratory results indicate that secondary breakage of a particular coal notably increases the specific amount of ATD generated, while negligibly impacting the specific amount of ARD generated. A strong positive relationship was identified between the specific amounts of ATD and ARD generated during the primary breakage process (with minimal secondary breakage), but a negligible relationship was observed between the same two variables when secondary breakage was introduced into the crushing process. This indicates that most of the ATD and ARD is generated from the primary breakage, while secondary breakage has a more of an influence on generating additional amounts of larger sized ATD. Additional experiments involving the uniform crushing of eight different bituminous coals showed that the coal rank, expressed as the inherent moist fuel ratio (MFR = fixed carbon =(volatile x inherent moisture)), had diverse relationships between the product size created and the amount of airborne dust generated. As bituminous coal rank or MFR increased, the amount of coal product fines < 250 gm increased while the mass percentage of ATD and ARD liberated from these < 250 µm product fines decreased. Air dry loss (ADL) moisture in the coal was found to be inversely related to the dust cloud electrostatic field, influencing dust liberation from the coal product fines. Since the MFR was directly related to the dust cloud electrostatic field, opposite the ADL-electrostatic field relationship, the diverse relationships between the product size created and the amount of dust liberated from the < 250 µm product fines were explained. Finally, 12 to 14 times more ATD was generated as compared to the ARD generated during these experiments. These results should provide a fundamental basis for initial estimation of the airborne dust loading requirements of engineering control methods for coal crushing.

By S. H. Ash

California leads the Nation in the number of operating metal mines and the small number of persons employed at individual mines, which reached a minimum irk 1932 with an average of seven men. The mines are scattered over the entire State, which is the second largest in area (155,562 square miles) in the United States. The mines are situated at various altitudes, with portals ranging from approximately 300 feet below sea level to almost 12,000 feet above. Many of the mines can be reached only during the summer, while at others the heat of the regions adds so the difficulties during the summer months Supplied of explosives the use (or, probably more correctly, the misuse) of which constitutes one of California&apos;s gravest mining problems; are handled and stored under condition that contribute many hazards. The problem of providing medical care is serious and complicated, especially at small mines and more particularly in the almost inaccessible mountainous regions; instances in which a knowledge of first aid would have been beneficial but was lacking, or when first aid was instrumental in saving life or limb because it was available are too numerous to be mentioned.

Jan 1, 1936

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

By C. A. Herbert

"The Workman's Compensation Law of Indiana, enacted in 1915, amended in 1917, 1919, 1923, and 1927, and in 1929 named the Indiana Workmen's Compensation Act of 1929, provides for a weekly compensation for disability due to accidents of 55 per cent of the average weekly wage of the employee, to start on the eighth day of disability. Compensation is computed from a maximum and minimum weekly wage of $30 and $16, respectively. Thus, the maximum weekly compensation is $16.50 and the minimum $8.80; the total compensation paid is not to exceed $5,000.In addition to the compensation the employer is required to pay all medical, surgical, hospital, and nurse fees for a period of 30 days and may be required to pay such fees for an additional 30 days at the direction of the Industrial Board of Indiana. In the case of fatalities the employer must contribute $100 toward funeral expenses.The law also stipulates that ""the employer shall keep a record of all injuries, fatal or otherwise, received by his employees in the course of their employment,"" also that the employer shall report within one week of their occurrence all accidents that cause either the death of the employee or the loss of more than one day's work. However, no standard form is furnished or required by the industrial board on which the employer shall keep a record of accidents, neither is he required to report the time of return to work of the injured employee unless the period of disability exceeds seven days and the accident thus becomes compensable. Hence, no record is kept of noncompensable accidents other than the first report sent to the industrial board by the employer.If the employer were required to keep a complete and concise record of all accidents, in duplicate, on a special form either furnished or required by the board, giving all of the essential data in regard to the accidents, and if he were required to submit a copy of this record to the board at the end of the fiscal year, the data thus assembled would not only be of material assistance to the board, particularly in making up its annual report, but would also furnish information of much value in the study of accident causes and what may be done to remove them.Those industries that have made marked progress in reducing accidents keep such records, as it is only through a full knowledge of how accidents occur that intelligent steps can be taken to prevent their recurrence. Unfortunately, the mining industry as a whole in Indiana has not kept pace with many other industries in reducing accidents, and it is urged as an aid to improvement that a thorough and complete record of mining accidents be kept."

Dec 1, 1932

By Maria I. De Rosa

Coal mine fires pose a constant danger to the safety of miners and to their livelihood. Underground mine fires pose an added hazard because of the confined environment with remote exits. Enactment of safety regulations [30 CFR2 75 and 771 for under- ground coal mines and surface coal operations has greatly improved the safety of miners. However, mine fires and fire injuries remain serious hazards for all coal mining operations. This report analyzes mine fires and fire injuries for all U.S. coal mining categories (underground coal mines, surface of underground coal mines, surface coal mines, and coal preparation plants) during 1990-1999. Fires involving contractors are also included in the analysis. Similar analyses (for underground coal mines only) by the former U.S. Bureau of Mines (USBM) were reported by McDonald and Pornroy [I9801 and Pornroy and Carigiet [I9951 for 1950-1977 and 1978-1992, respectively. For comparison purposes, data for 1978-1 992 are mentioned in the "Underground Coal Mine Fires" section of this report. Detailed analyses of mobile equipment fires for all underground and surface coal and metal/nonmetal mining categories during 1990-1999 have recently been reported by NIOSH [De Rosa 20041. Risk rate values (fire and injury risk rates) for the 10-year period (1990-1999) and for five successive 2-year periods within the 10-year period are derived. Risk rate values for individual states for the 10-year period are also derived. Other variables by state and time period include employees&apos; working hours, lost workdays, and coal production (underground and surface coal mines only). The number of fire fatalities is reported by time period. Variables such as ignition source, method of detection and suppression, equipment involved, location, and burning material are reported by five 2-year periods only. Furthermore, the number of fire injuries per number of fires causing injuries and total fires has been analyzed by year, ignition source, equipment involved, and location. For comparison purposes, the major fire and fire injury findings for all coal mining categories have been reported. The data in this report were derived from "Injury Experience in Coal Mining" [MSHA 1991a, 1992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001, "Fire Accident Reports" [MSHA 199 1 b,c; 1994b; 1995b,c; 1998a,c,d,e,f; 1999a,b,d,e], MSHA "Fire Accident Abstracts" internal publications, and verbal communications with mine personnel. Mining companies are required by 30 CFR 50 to report to MSHA all fires that result in injuries and fires that are not extinguished within 30 min of discovery. A small number of fires lasting <30 min without injuries reported in the "Fire Accident Abstracts" have been included in this report. The analysis in this report will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the causes and hazards of mine fires and fire injuries. It will also form a basis for developing future fire research programs.

Jan 1, 2004

By Jon K. Ahlness

The Bureau of Mines, in cooperation with the Institute of Mineral Research of Michigan Technological University, and the Upper Great Lakes Regional Commission, conducted an investigation of electronic sorting of native copper ore from Upper Michigan. This report is based on research by the Institute of Mineral Research under contract to the Bureau. The test program evaluated the use of belt and rotary sorters on various size and grade fractions of ore. Both plant-scale sorting and lab sorting tests were run. The plant sorting objectives were to determine the sortability of different ores and the efficiency of the electronic ore sorters. High-and low-grade ores from both conglomerate and amygdaloid types were separated into four size fractions. The two larger sizes were sorted on belt sorters and the two smaller ones on rotary sorters. Copper recoveries ranged from 20.0 pct from a feed grade of 0.40 pct to 80.3 pct from a feed grade of 1.08 pct. Lab sorting tests of conglomerate ore were run to determine the efficiency of a belt sorter equipped with a second sensing coil located above the belt and to determine the sorting characteristics of larger ore size fractions than those used in the plant sorting. Copper recoveries from the combined feed sizes ranged from 47.0 pct from a feed grade of 0.13 pct to 96.8 pct from a feed grade of 4.87 pct. For all the ore types except one, it was found that the copper recovery increased with the feed size.

Jan 1, 1980

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not wholly devoted to mineral commodity transport, as seen in tables 16 through 22. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to non mineral goods, as well as carrying mixed mineral commodities and non mineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Table 16 shows the distribution of the world&apos;s merchant fleet by vessel type in terms of the number of vessels, their gross tonnage, and their deadweight tonnage. The increase of nearly 1.5 % in the number of vessels between 1990 and 1991 compared with a 2.7% growth in gross tonnage and a nearly 2.3 % increase in deadweight tonnage points to an increase in the average size of vessels. Of the four categories of vessels reported, all showed increases in number and in deadweight tonnage between 1990 and 1991 except for "other," and on the gross tonnage basis, all groups registered increases. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1993

By J. Douglas Causey

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 7,940-acre Southern Otay Mountain Wilderness Study Area (CA-060-029), and the 5,750-acre Western Otay Mountain Wilderness Study Area (CA-060-028) in order to evaluate their mineral resources. The wilderness study areas are located in San Diego County, CA, about 20 miles southeast of San Diego. No mineral resources were identified in the Southern or Western Otay Mountain Wilderness Study Areas, based on literature, field observations, and sample results. The wilderness study areas are underlain by a complex blend of Late Jurassic, moderately metamorphosed sedimentary and volcanic rocks. Evidence of mineralization is not obvious.

Jan 1, 1987

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler&apos;s sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of sold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium Which such samples contain.

Jan 1, 1934

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler&apos;s sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By R. V. Ramani, V. T. Burgos, J. A. McClay

Cost Data Library The data retained in the Cost Data Library is of a semi¬permanent nature in that it is held in storage for immediate use with the program although its contents may require periodic evaluation to maintain it in a current status. The library is composed of six arrays containing both technical and cost data. The following description of the library input system provides the information necessary to maintain an active storage file. Array POWERA: FORMAT (8F10.0) - contains the step groupings of the power rate schedule for power cost computations. Four input data cards are required to fill this storage area. Card Column 1 1 - 10 Demand in Kilowatts for the First Step of the Demand Rate Schedule 11 - 20 Demand in Kilowatts for the Second Step of the Demand Rate Schedule y 41 - 50 Demand in Kilowatts for Fifth Step of the Demand Rate Schedule 51 - 60 Maximum Demand Level for this Rate Schedule 61 - 70 Percent Power Factor for this Rate Schedule 71 - 80 Unassigned 2 1 - 10 First Step Demand Charge, $/Kw 11 - 20 Second Step Demand Charge, $/Kw 4¬ 41 - 50 Fifth Step Demand Charge, $/Kw

Jan 1, 1975

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965