Search Documents

By C. E. Wethered

This paper describing the mining methods employed by the Federal Mining and Smelting Co., operating the Morning mine at Mullan, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The daily tonnage produced at the Morning mine, including that mined by leasers, is 1,100 tons. Mine run of ore will average 9.1 per cent lead, 5.8 per cent zinc, and 4.4 ounces silver per ton. A stull set and fill method of mining is employed.

Jan 1, 1930

By L. A. Johnson

This Bureau of Mines report presents the analysis of three cores from the Asphalt Wash area of the P.R. Spring tar sand deposit of northeastern Utah. Two tar sand zones are indicated in the Asphalt Wash Area. Total net thickness of the tar sand ranges from 23 to 39 ft, with occurrences between 56 and 263 ft in depth. The sand has average porosity of 24.7 pct of bulk volume, average permeability before and after extraction of 87.5 and 596 md, respectively, and average oil saturation of 58.1 pct of pore volume. Oil gravity averages 10.9° API.

Jan 1, 1975

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By John J. Gordon, Neil K. Cooperrider

The International Organization for Standardization (ISO) standard ISO 2631 [1,2] provides three methods for evaluation of human exposure to vibrations that contain occasional shocks or impacts. Part 1 of the standard specifies the running r.m.s. or maximum transient vibration method (MTVV) and the fourth power vibration dose value (VDV). Part 5 of the standard provides a method of computing the stress in the lumbar spine for humans exposed to multiple shocks. Alem et al [3] have reported application of these methods to data for tactical ground vehicles. This paper reports and compares VDV and spinal stress evaluations of more than 90 hours of vibration and shock measurements on North American locomotives engaged in through freight operations. The measurements evaluated in this paper were obtained for full crew shifts on 19 freight locomotive runs on mainline track in locations from New York to California. The shifts ranged in duration from 187 minutes to 497 minutes. The average speeds for the shifts were from 21.0 mph to 54.6 mph. All measurements were made on locomotives hauling freight trains in regular revenue service. Data Acquisition and Processing The results reported here were computed using test data acquired from a tri-axial seat pad, accelerometer at a sample rate of 400Hz with an anti-aliasing filter corner frequency of 100Hz. The VDVs and the lateral and longitudinal spinal stress values were computed directly from the acquired test data according to the procedures specified and described in [1] and [2]. The vertical spinal stress values were computed by converting the as-acquired test data to a sample rate of 160Hz for input to the vertical spine model, as required in [2]. The conversion of the test data from the as-acquired sample rate of 400Hz to the required sample rate of 160Hz involved up sampling or interpolating the test data to an equivalent sample rate of 800Hz, band limiting the resultant data with a low-pass filter corner frequency of 60Hz and finally down sampling or decimating the 800Hz data to a sample frequency of 160Hz. Discussion The vertical VDVs computed according to [2] for the 19 shifts ranged from 2.68 to 9.33 m/s1.75. In all but one case, the vertical values were greater than the values for the lateral or longitudinal directions. Note that the health guidance in [1] puts the lower boundary of the health guidance caution zone at a VDV value of 8.5 and the upper boundary at 17 m/s1.75. The daily equivalent static compression dose computed following [2] ranged from 0.123 to 0.434 MPa. Health guidance provided in [2] states that there is a low probability of an adverse health effect if the daily dose is less than 0.5 MPa.

Jan 6, 2006

By R. C. Wang, W. M. McKewan

The behaviour of wire ropes used in mine hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analysed. This report provides a generalised mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix. The other is used for the paths of double helical wires. The specific model for a 33-mm 6x1 9 Seale, IWRC, right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires which include the path length per lay of strand, the curvature, and the torsion were determined from this model. In future work, the model could be used to conduct stress analysis for the wires in the deformed rope at a given rope strain and also to study the effect of wear and breaking of wires on strength loss for the various round-strand wire ropes used in mine hoisting.

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed lint of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have boon modified as covered by extensions of the original approvals.

Jan 1, 1941

By A. C. Fieldner

The Bureau of Mires in its investigations of gas masks for use in mines and allied industries has studied and developed various types of masks for protection against noxious uses and furies that may be present in atmospheres encountered in mines, metallurgical works, chemical and other industries. As a result of these investigations, the Bureau issued a schedule5 of tests under which manufacturer who voluntarily submit masks for examination and test, are issued an approval certificate for masks that meet the Bureau's specifications. In the Bureau's schedule, masks arc classified by types of gases removed, as type A masks for protection against acid gases; B; organic vapor; C, ammonia; D, carbon monoxide; E, smoke, dust, and mist; F, special gases; combination types, and type N, for protection in air against all gases, vapors, and smokes. The purpose of this paper is to describe the physical and chemical tests that were conducted on a type N mask, the protective principles and construction of the essential elements of the canister and attachments, and the uses and limitations of this type of mask. The mask tested is known as the all-service mask, manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa;, and was approved (approval No. 1403) by the Bureau on July 1, 1924, for protection from all classes of poisonous vapors, gases and smokes in air.

Jan 1, 1925

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

By Kenneth C. Stewart

This contract was directed toward a study of the attenuating properties of earmuffs as worn by miners. Two attenuation measurement procedures were utilized. Human subjects were tested in a diffuse sound field according to threshold shift procedures recommended by the American National Standards Institute and a physical measurement procedure was accomplished in the same diffuse field on the same human subjects with microphones placed simultaneously on the inside and outside of the muffs. All measurements were obtained in one third octave of random noise. The results of the study indicated that physical and psychophysical attenuation measurements are in essential agreement at frequencies from 125 Hz to 2 KHz. Above 2 KHz the psychophysical measurement demonstrates larger amounts of attenuation than the physical measurement. The difference in attenuation ranged from approximately 7.0 dB to 9.0 dB at frequencies of 4 KHz and above. A possible explanation for the observed differences in attenuation has been presented.

Jan 1, 1980

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2000

By C. F. McCarroll

[Laboratory research and, control in the u?odnction an; utilization of petroleum and its product s have eqLmde& greatly during the past decade, rind much of the routine control and experimental equipment noirr requires the con-stant daily use of liquid nercury. In spite of this greater use, very little consideration has becn given to the hazard that might be occasioned by the toxic vapors of mercury unavoicl.a~l.p spilled or otherwise exposed to the atmosphere during the normcl 2rgced1u.e of ln30r~tor;~r operations. A sfmple visual exami~stion gf' sone of the laborztories reveals the prescnce of a considerable quantity of mercury in the craclcs of floors, on work tebles, ad on and mo7md eql~ipmeilt st.ads. Usually this yercurj ie contaminated with oily and dirt BO th~t it remint; in R finely divided state and a srnarl amount presents a relativell- lag? surface for evaporation. Since mercury shows meas~rable vo!-atility st a tempero.turc as lor^ 2s 8.5O F., mercury vapor will bo present in the atnosphere of anjr laboratory wbr.e mercury is exposed. promiscuously]

Jan 1, 1939

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962