Search Documents

By W. E. Miller, W. P. Yant, G. W. Jones, R. E. Kennedy

"The determinations of the limits of inflamability of diethyl ether and ethylene in air described in this report were made primarily for comparison with similar determination of other compounds in the same apparatus and by the same laboratory technic. The experimental procedure and the results obtained differ somewhat from those of other investigations. The work also included determinations of the limits of inflamability of these combustibles in oxygen The investigation,was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines in cooperation with Merck & Co., Inc. LIMITS OF IMFLAMIABILITY OF DIETHYL ETHER-AIR MIXTURESThe limits of inflamability if diethyl ether in air were determined for upward propagation of flame in an upright, closed 8-liter, cylindrical iron bomb 10.2 cm in inside diameter and 96.5 cm in length. This bomb been described in a previous publication. 6Two brands of diethyl ether were used, one a C. P. sulphuric ether manufactured by Baker & Adamson, and,the other Merck & Co. product manufactured for anaesthesia and containing about 3.5 percent of ether alcohol."

Jul 1, 1935

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

Provide a full-scale test facility where the effectiveness of all types of subsidence abatement techniques can be evaluated under controlled conditions. Background Subsidence is ground movement resulting from the collapse of overlying strata into a mine void because of failure of the mine roof, mine floor, or support pillars. The failure may propagate to the surface and be expressed as a depression, cracks, or a sinkhole. The surface expression of such features may be delayed until long after mining has been completed. Subsidence has the potential to affect more land area than any other type of abandoned mine land problem. Subsidence also causes direct damage to real property, with significant financial loss and more importantly, presents a danger to public health, safety, and general welfare. Subsidence-related problems are considered to be one of the most important abandoned mine land issues. Backfilling of mine voids is the most common stabilization method used to abate subsidence and protect surface structures. Backfilling or placement of material is performed by hydraulic flushing or pneumatic stowing, using either in-mine or remote methods. The majority of the past subsidence abatement projects has been performed using remote methods from single or multiple boreholes. Other subsidence abatement techniques arc available. For example, various point support methods are used to protect small areas of the land surface and surface structures, without completely filling the mine void. These may be more appropriate under different conditions. Little documented information is available concerning the capability of the various backfilling methods for completely filling a mine void or providing long-term structural strength. Therefore, the Bureau of Mines developed a laboratory for controlled evaluation of backfilling technologies.

Jan 1, 1991

Etching solutions containing hexavalent chromium ions (e.g., chromic acid) are used in brass finishing, printed circuit board etching, preparation of plastic for plating, anodizing, and various other industrial surface treatment operations. As the solutions are used, hexavalent chromium ions are reduced to their trivalent state, contaminants accumulate in the solution, and the effective acid concentration is reduced. When the etching rate becomes unsatisfactory for the particular operation, the solutions are discarded. This is a problem because the discarded solutions are pollutants, and because replacing the etching solution is expensive. The Bureau of Mines has developed a process for regenerating these spent solutions and returning them to the surface treatment operation without interrupting the etching process. An electrolysis cell containing anode and cathode compartments that are separated by permeable membranes, is used for regenerating the spent solutions. The spent chromic acid solution is fed to the anode compartment and sui (uric acid is circulated in the cathode compartment. Application of a steady electrical potential of a few volts dc across the electrodes causes the copper ions and other contaminants in the spent solution to migrate through the membrane to the cathode compartment where copper is plated onto the cathode. Zinc and the other contaminants remain in the sulfuric acid. At the same time, the complex, trivalent chromium ions in the spent solution are attracted to the anode where they are oxidized to their original hexavalent state. The regenerated solution in the anode compartment is then recycled back to the plant?s etching operation for reuse.

Jan 1, 1980

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned coal fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and could be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the. 1900's and was surface mined in the 1940's. In the winter of 1961~62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated but, not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report, although considered part 2, is actually the last of a five-part series that describes the Calamity Hollow Mine Fire Project. It was written last because it involved the analysis of a substantial body of data describing in detail the results of a continuous 4-month burnout operation. The first report, part 1, describes the design and construction of the field installation. Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. Parts 4 and 5 deal with the closeout phase of the field demonstration. Part 4 describes the procedure used to quench the fire, and part 5 describes the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is suffIcient for energy utilization, and (3) water injection-fume exhaustion is a potentially effective method for cooling large underground fire zones. Further investigations of both Burnout Control and the water injection-fume exhaustion quenching procedure are planned.

Jan 1, 1989

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By Jon C. Volkwein

Advances in mining technology have enabled deeper seams of coal to be mined from the surface. Highwall mining is frequently used to mine areas at the perimeters of a surface mine when removal of the overburden becomes uneconomical or threatens environmentally sensitive surface features. At the same time, advances in materials and technology have enabled highwall mining of coal that create blind headings over 300 meters in length. Deeper surface mining and deeper highwall penetration depths have lead to more frequent encounters with methane gas. While this coal is remotely mined from the surface, underground ignitions of methane have propagated to the surface and injured miners. Methods described in this paper show how this hazard can be correctly monitored and controlled for auger type highwall mining machines. Research indicates that small quantities of gas liberated during mining migrate to the face, creating higher gas concentrations than would otherwise be expected. Using the same principles that cause the gas to migrate to the face, researchers have shown that inert gas introduced at the collar of the hole can inert the entire hole, thus ensuring safe conditions for mining.

By L. J. Froisland

The U.S. Bureau of Mines conducted laboratory studies on sulfuric acid (H2S04) digestion of alunite [KA13(S04)2(OH)6] as a means for treating domestic deposits of this mineral. Digesting alunite ore in boiling H2S04 at concentrations of 88-wt-pct acid or higher breaks down the alunite and permits a convenient separation of potassium and aluminum. The digestion reaction is a complex sulfation reaction occurring in two stages. In this reaction, the potassium component extracts into the H2S04 for eventual recovery as potassium sulfate k2s04 in a separate unit operation. Aluminum is left as acid-insoluble aluminum sulfate [A12(S04)a], which can be extracted by a 95° C water leach. Additional purification of AI2(S04)a produced in this study is needed to meet cell-grade alumina (Al202) purity specifications. Extraction and separation of potassium and aluminum from the alunite ore were consistently above 90 pct.

Jan 1, 1989

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By L. B. Pankratz

Enthalpies were determined for synthetic chalcopyrite (CuFeS2) between 298° and 1,050° K and for synthetic bornite (Cu5FeS4) between 298° and 1,100° K by copper-block drop calorimetry. Two transitions were found for each compound. The lower transitions were both crystal transformations from tetragonal (low-temperature form) to cubic (high-temperature form). The chalcopyrite transformation occurred at 830' K with a heat of transformation of 2,405 cal/mole; the bornite transformation was at 485° K with a heat of 1,430 cal/mole. The other transitions were of the second order and were presumed to be magnetic in character. The second-order transitions for chalcopyrite occurred at 930° K, and the one for bornite at 540° K. Enthalpy increments, entropy increments, and heat capacities are tabulated at even temperatures above 298.15° K. Equations of enthalpy are also given.

Jan 1, 1970

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

By John T. Kuo

The miner's seismic source strength can be approximately estimated on the basis of a single force acting in an infinite medium. Because of the uncertain- ty involved in estimating the amount of conversion from mechanical energy to seismic energy, the source strength thus estimated may be in error by as much as a half-order of magnitude. Calculations of wave transmission must take into account geometrical spreading, dissipation of energy by internal friction, and energy partition due to reflection and refraction of waves impinging on inter- faces in the layered earth. Theoretically derived peak-to-peak particle velocities in microinches per second (PIPS) are given for two models ; viz: (i) 50-feet thick and (ii) 100- feet thick 4000 ft/sec layers with Q = 20, overlying a half-space of 10,000 ft/sec material with Q = 5O;for the cases .of a hammer blow and a timber impact, at the frequencies of 50 Hz and 100 Hz. Comparison of the theoretically derived peak-to-peak particle velocity with experimental data taken at the Copper Queen Mine indicates that the theoretical particle velocity may be overestimated. A discussion of the distortion of seismic wavefronts by mine tunnels indicates that it is unfavorable to use a seismic source impact on the floor of the tunnel, since deceptive delays in arrival time are liable to occur at the surface. A program of parallel theoretical and experimental work is required to clarify uncertainties still associated with the nature and strength of the miner's seismic source signal which cannot be resolved within the approximations of this work. Its major components include theoretical investigations of the (1) Wave diffraction and scattering of an impact source on a face of a cylindrical cavity. (2) Impact of an elastic object on an elastic medium.

Jan 1, 1974

By Steve Bessinger, Steve Signer, James Pile

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining affected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied. This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

By Charles L. Kimbell

Some comment on data availability must be an integral part of a study such as this. For many years, the centrally planned economy nations of the world regarded as state secrets much of their mineral commodity production information, as well as a considerable body of the foreign trade information on these commodities, and virtually all reporting on their consumption. Within the past 5 years, this pattern has undergone some evolution, and although these countries still fall short of market economy countries in their willingness to publish, there has been measurable improvement. Fit, China, and then subsequently the former CMEA member countries of Eastern Europe have released in print an increasing amount of information in organized, coherent formats, although in a number of cases it is not clear that the information provided is in perfect definitional accord with market economy country practices. Thus, these recently available statistics must be carefully studied to ensure that they are provided in terms of conventional market economy definitions. At the same time that heretofore unpublished information is becoming available for the centrally planned (or formally centrally planned) economy countries, there has been a slow but steady disquieting erosion of availability of production, trade, and consumption data for market economy countries. There are evident reasons for some of these losses in information. The foremost of these relates to corporate mergers. As the number of producing or consuming firms of a given commodity in a given political jurisdiction declines, it is increasingly difficult for government agencies to protect proprietary company data. In past years, this protection was afforded by aggregating data for the several companies operating in the area, but as the number of operators diminishes this is no longer always possible. Hopefully, given this situation, companies will at least authorize release of data after a period of time, when its publication will not provide competitors with unfair access, but will make possible longer term studies.

Jan 1, 1992