Search Documents

By R. J. Hundhausen

The Takilma-Waldo copper district in Josephine County, Oreg., was studied by the Bureau of Mines from September 1950 to April 1.951 and from December 1953 to April 1954. Funds for the investigation were provided by the Bureau of Mines and the California-Oregon Power Co., Medford, Oreg., on a cooperative basis. The copper mines in the district are credited with a total production of ore worth $1,700,000. Since 1933 the mines have been unproductive and, except for minor exploration, largely inactive. The history of the district indicates that the copper deposits were mined principally during periods of high metal prices.

Jan 1, 1956

By Richard A. Winters

The 31,880-acre Battle Creek Wilderness Study Area (WSA) was evaluated for mineral resources by the U.S. Bureau of Mines in 1984. No mining district is in the area, nor were any mines or claims recorded or found. Oil and gas leases, or lease applications, covered about half the area in early 1984. No known exploration has occurred. The entire WSA is covered with thick volcanic flows. Faults in these volcanic rocks may have provided conduits for mineralizing solutions emanating from the basement rocks; however, no evidence of mineral deposits was detected from rock samples collected along the faults. Reconnaissance samples from sand and gravel deposits yielded gold at less than $0.02/yd3. The source of the gold is assumed to be intrusive rocks or the Challis Volcanics about 20 miles north of the study area near the headwaters of Battle Creek. No economic concentrations of minerals were found in the WSA. INTRODUCTION Mineral surveys of designated wilderness study areas (WSAs) 1/ are conducted by the U.S. Bureau of Mines (USBM) and the U.S. Geological Survey (USGS) at the request of the U.S. Bureau of Land Management (BLM). The USBM researches the mining and mineral exploration history and evaluates mines, prospects, and mineralized areas within or adjacent to WSAs. The USGS studies WSAs by regional geochemical and geophysical surveys and geological mapping. The USBM and the USGS investigations are summarized in a joint report used to help determine the suitability of WSAs for inclusion into the National Wilderness Preservation System. Although the immediate goal of this USBM study is to provide data for the President, Congress, BLM, and the general public for land-use decisions, the long-term objective is to help insure that the Nation has an adequate and dependable supply of minerals at reasonable cost.

Jan 1, 1985

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise might be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and removing the disintegrated clay particles from wells after the perforated Wipes have been inserted. Mechanical methods for removing mud sheaths are :quite satisfactory, but prompted by the request of certain .operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions. This report describes the laboratory work and deals generally with a chemical method for removing the mud sheath, cake, or plaster deposited against the face of oil sands in drilling wells end in wells that, on being shut in temporarily during periods of overproduction of oil, are conditioned for the shutdown .period by filling the well opposite the producing formations with mud fluid. The method described in this report was devised in the San Francisco laboratory of the Bureau of Mines and, as far as the writers have been able to determine, differs from any chemical method ever used in actual wells. The method proposes to add a small amount of calcium carbonate (preferably pulverized limestone) to the mud fluids before they are introduced into the wells so that the resultant mud sheaths will be susceptible to disintegration by acid solutions when it is desired to expose the faces of the oil sands in the wells.

Jan 1, 1934

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By J. B. Stephenson

The Bureau of Mines, under an interagency agreement with the Department of Energy (DOE), investigated the feasibility of hardfacing the critical surfaces of valves and similar devices by chemical vapor deposition. The purpose of this research was to increase the wear resistance of these components for use in the abrasive and erosive environment of coal gasification units. Tungsten and molybdenum coatings were produced on nickel-plated carbon steels and stain-less steels by hydrogen reduction of the metal hexafluoride at 325° to 600° C. Titanium nitride coatings were produced on low-carbon steels by the reaction of titanium tetrachloride, hydrogen, and nitrogen at 1,000° C. Titanium carbonitride coatings were produced on low-carbon steels by the reaction of nitrogen, hydrogen, and methane at 900° C. Tungsten, molybdenum and titanium nitride coatings were formed on 6-, 10-, and l2-inch (0.15-, 0.25-, and 0.30-meter) ball valve seats for evaluation in the low-Btu coal gasification pilot plant at the Morgantown Energy Research Center, Morgantown, W. Va.

Jan 1, 1979

By Wilbur Duvall

For the past few years the Applied Physics Branch has been investigating, experimentally, the generation and propagation of strain waves in rock. The strain waves are produced by the detonation of a high-velocity explosive placed in a small cavity in the rock. Strain gages mounted in the solid rock surrounding the cavity record the strain pulses propagated away from the source. Numerous strain-wave pulses have been recorded in different rock types for charges of various sizes and at various distances from the charge. Analysis of these records has shown, among other things, that there is associated with the strain wave a characteristic pulse width. This pulse width is dependent on the rock type and the distance from the shot point to the gage, but is apparently independent of the charge size or cavity size. Recent published literature on the generation and propagation of seismic waves indicates that the characteristic frequency of an elastic wave generated by an explosion should be a function of the rock type and the size of the cavity created by the explosion. Also, internal friction in the rock would produce absorption of high-frequency components, which would cause continual change in the shape of the pulse propagated. As the experimental data did not verify the expected change in pulse shape with cavity size, a theoretical investigation of the vibrations associated with a spherical cavity in an elastic medium was undertaken.

Jan 1, 1950

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963

By George H. Holmes

This report describes the results of a reconnaissance survey of areas in California and Nevada considered favorable to beryllium mineralization. Pegmatite dikes, veins, intrusive sills, contact metamorphic, and disseminated deposits as well as tactite deposits in the former major tungsten-producing districts were investigated. A general geographic pattern of beryllium mineralization was found to be concentrated along a wide belt in eastern Nevada extending from the Ruby Mountains, Elko County, south through the Fish Creek Range, Eureka County, the Snake Range, White Pine County to the Virgin Mountains in Clark County, Nev., and Mohave County, Ariz. Sporadic occurrences of beryllium are in central and southern Nevada, and in the pegmatite dikes of San Bernardino, Riverside, and San Diego Counties, Calif., and the granite masses of the southern Inyo Mountains, Inyo County, Calif. Principal company activities are centered in the Snake Range, Fish Creek Range, and the Virgin Mountains, Nev., and the Inyo Mountains, Calif. Other areas in California and Nevada have been superficially explored with results indicating either limited or widespread, but submarginal, mineralization. Although beryllium was found to occur, to some extent, in many of the deposits, mining has been hindered by the lack of a market for beryllium ores and concentrates other than standard-grade beryl and also by the erratic pattern of mineralization and the high exploration and beneficiation costs required to produce a marketable product.

Jan 1, 1963

By George H. Holmes

This report describes the results of a reconnaissance survey of areas in California and Nevada considered favorable to beryllium mineralization. Pegmatite dikes, veins, intrusive sills, contact. metamorphic, and disseminated deposits as well as tactite deposits in the former major tungsten-producing districts were investigated. A general geographic pattern of beryllium mineralization was found to be concentrated along a wide belt in eastern Nevada extending from the Ruby Mountains, Elko County, south through the Fish Creek Range, Eureka County, the Snake Range, White Pine County to the Virgin Mountains in Clark County, Nev., and Mohave County, Ariz. Sporadic occurrences of beryllium are in central and southern Nevada, and in the pegmatite dikes of San Bernardino, Riverside, and San Diego Counties, Calif., and the granite masses of the southern Inyo Mountains, Inyo County, Calif. Principal company activities are centered in the Snake Range, Fish Creek Range, and the Virgin Mountains, Nev., and the Inyo Mountains, Calif. Other areas in California and Nevada have been superficially explored with results indicating either limited or widespread, but submarginal, mineralization. Although beryllium was found to occur, to some extent, in many of the deposits, mining has been hindered by the lack of a market for beryllium ores and concentrates other than standard-grade beryl and also by the erratic pattern of mineralization and the high exploration and beneficiation costs required to produce a marketable product.

Jan 1, 1963

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By John A. Johnson

Tests ere conducted at the Mount Weather testing adit of the 57 Bureau of Mines on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. Equipment Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is mace of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.

Jan 1, 1939

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 19274 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil-, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein. Bulletin 2916 states that many oil producers and refiners use the word "base" much as it is used in pharmaceutical work. For example, the "base" or "basis" of an ointment or salve is the fatty material (lard, petroleum, or lanolin) used as a vehicle or carrier for the active medicinal principles. Apparently many of the pioneers in the petroleum industry considered crude oil similar in nature to these medicinal products in that it consists of a semisolid, nonvolatile base and 1 volatile portion can be distilled off to make gasoline, kerosene, and other products. Many crude oils when chilled slowly deposit a waxy material (paraffin); this fact may have been one reason for the use of the term "paraffin base" in referring to such oils. Almost all of the petroleum first discovered in the United States was of this nature; not until the oil industry was extended to California and along the Gulf coast was petroleum found that contained no wax but apparently did contain asphaltic material Accordingly, these oils were known as "asphalt-base" oils. The use of this term, however, seems unfortunate, as better-grade oils of this type contain little if any asphalt; the descriptive term "naphthene base" now seems to be a more desirable term than "asphalt base." The term "intermediate base" is also used commonly in referring to oils intermediate in oharacteristios between those of paraffin and naphthene base.

Jan 1, 1935

By Paul W. Jeran

Subsidence over a series of longwall panels undermining sloping terrain in southwestern Pennsylvania was monitored to verify the Bureau of Mines subsidence prediction model for the northern Appalachian coal region. Comparison of the field data to model output shows close agreement. Vertical movements over each panel ceased with the mining of the adjacent panel. Horizontal movements were significantly affected by topographic slope. The distribution of horizontal strains over each panel were similar, with a zone of compression occurring over the center of each panel. The zones of compression were flanked by zones of tension toward the rib. The magnitude of the tensions were affected by the slope. The strains developed at the completion of each panel were not significantly altered by the mining of subsequent panels.

Jan 1, 1988

By J. J. Bean

This paper, describing the milling practice at the oxide concentrator of the International Smelting Co., is one of a series on milling methods and costs being published by the United States Bureau of Mines. GENERAL DESCRIPTION The oxide concentrator is properly an integral part of the Tooele plant of the. International melting Co., located 5 miles from Tooele, Tooele County, Utah. It has a capacity of 300 tons of ore per day and uses an all-flotation process to treat custom siliceous oxidized lead ores obtained principally from the Tintic district in Utah. Ores found amenable to the process are purchased on a custom basis, the principal tonnages being obtained from the Tintic Standard and North Lily mines.

Jan 1, 1933

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By S. L. May

Tantalum and columbium can be extracted from several of their ores or concentrates by chlorination procedures. Direct chlorination of high-grade minerals in the presence of carbon at temperatures between 500° and 800° C will extract up to 99 percent of the tantalum and columbium. Metallurgical beneficiation of low-grade source materials by carbothermic reduction produces a ferroalloy that is amenable to chlorination at a temperature of 500° C. Over 90 percent of the tantalum and columbium can be recovered.

Jan 1, 1965