Search Documents

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By L. C. IlsLey, H. H. Clark

As part of its investigations of the causes of mine accidents and of the safest and most efficient methods of handling electricity underground, the Bureau of Mines undertook a study of the ignition of mine gases by the filaments of electric incandescent lamps. This bulletin describes the investigation in detail and gives a complete record of the results obtained.

Jan 1, 1913

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939

By Murray Greyson

A number of tests were made with various methanation catalysts in fixed-bed, conventional fluidized-bed, and multiple-feed, fluidized-bed equipment to develop catalysts and processes for methanation of synthesis gas. The results show: 1. Methanation reactions may be carried out in 1-inch, bench-scale equipment at high synthesis-gas throughputs with good temperature control of the reactions if a multiple-feed type of fluidized-bed design is used. 2. Nickel is superior to iron as a catalyst for the methanation of synthesis gas, unless the process is considered in terms of a combined operation that produces both gaseous and liquid products. 3. Techniques of catalyst preparation determine, to a large extent, the process life of nickel catalysts, and these techniques must be thoroughly investigated before any conclusions can be reached. 4. Enough data are available to indicate that the sulfur concentrations in synthesis gas that is used for methanation are extremely critical, and maximum process limits should be carefully evaluated.

Jan 1, 1955

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

The initial results from the magnetic sludge factorial experiment are summarized in Table 2. For ease in interpretation, the four separate variables are identified with the high and low level of each variable being represented by + and - signs, respectively. Several important relationships are evident from an inspection of the data in Table 2. For example, magnetic sludges were obtained only during the high temperature tests. Secondly, with the exception of the last three tests, there is an apparent correlation between settled sludge volume (or sludge settling rate) and pH. Data on residual dissolved Fee+ indicate that precipitation of iron is not complete at pH 8 and room temperature (Tests l, 3, 5, and 7). Although this should not have any confounding effect on the interpretation of the results, it is an important observation and an aspect of the overall conceptual process that should be considered carefully during any future developmental work. The data in Table 2 were employed more fully in the calculation of main effects and variable interactions for each of the three responses. For this purpose, a codified design and calculation matrix, shown in Table 3, was used. The derivation of this matrix is described by Davies.(9) The positive or negative signs for variable interactions are obtained simply by algebraic multiplication of the signs for each single variable involved in the interaction. Main effects and interactions are calculated by multiplying the response values (Table 2) by the corresponding effect elements (Table 3), summing the results, and dividing by 8. The resulting value for single variables is also sometimes designated as an average effect, since (for tyro levels of the variable only) it is simply the difference between the average response of all trials carried out at the first level of the variable (factor) and that of all trials at the second level. If the effect of one variable changes at different levels of another variable, the two variables are said to interact. The relative importance of the variable or variables in question is reflected by the absolute magnitude of the calculated main effect or interaction. First-order (two variable) interactions are usually easy to interpret in terms of the physical behavior of the system. Second- and higher-order interactions are often less readily understood, and are often of minor significance in any case. The main effects and interactions derived from the present study in the manner described above are listed in Table 4. It should be noted that

Jan 1, 1971

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By Michael J. Magyar

The Federal Bureau of Mines has developed a hydrametallurgical method to recover aluminum, aluminum oxide, and fluxing salts from aluminum salt slags. The slag is leached with water at room temperature to produce a saturated brine slurry. Screening of the slurry yields an aluminum-rich fraction that can be returned to the dross furnace. The remaining slurry is vacuum filtered, yielding a clear brine solution and an aluminum oxide filter cake. Evaporation of the clear filtrate produces a high-purity fluxing salt for reuse in the dross furnace. Over 80 pct of the metallic aluminum is recovered in the aluminum-rich oversize fraction, while essentially all the fluxing salts are recovered by evaporation. This report contains the final results of an investigation on a process research unit scale, an economic evaluation of the method, and recommendations to further improve the process.

Jan 1, 1979

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By Henry M. Harris, Hal J. Kelly

Electrical dewatering tests are described in which the laboratory cells were designed for continuous operation using an endless metal belt as the anode . The test slurries were dilute , containing from 2.5 to 14.4 percent solids (specific gravity of 1.02 to 1.10 ) that were all minus 8 microns in size . Recovery of the solids of low water content was the practical objective of the investigation . Process variables evaluated and reported are : The effect of feed rate , amount of electrolyte , samples from different sources , and the use of two cells in series . These variables are evaluated on the basis of yield of clay per kilowatt - hour , recovery , and the amount of solids in the deposited clay . Recovery , yield , and solid content of the belt anode product are interdependent , and changes that will improve one of these characteristics often are accomplished at the expense of the others . Tests in which recoveries range from 50 to 60 percent usually result in yields of 8 to 9 kilograms (kg ) of dry clay per kilowatt- hour (kwhr ) . Under these conditions , the solid content of the deposited clay approximates 50 percent . One test sample , composed of kaolinite , showed very high yield , 13 to 16 kg per kwhr ; high recovery , 53 to 58 percent ; and 52 to 54 percent solids in the cake .

Jan 1, 1964

This Bureau of Mines report on underground mine communications addresses methods and equipment to meet the communication requirements of working sections and places of coal and metal-nonmetal mines. A review of the status of trapped miner detection is also presented.

Jan 1, 1977

By O. C. Ralston

Natural or artificial manganese dioxide of a grade pure enough to be satisfactory as depolarizer for dry cells has never been available in large supply simultaneously with being available in desired quality . The Second World War called for more of it than ever . A supply of natural material from the Gold Coast was ample for the war and was not completely exhausted . Whereas the crystal form of the manganese oxide was not recognized as a matter of importance until the war came , it is now known that gamma MnO2 is a desirable form and that pyrolusite , once thought acceptable , is not the best mineral . The following paper is a translation of an internal company report filed at the Bitterfeld office of the I. G. Farbenindustrie A.G. by Dr. Peter Marx in 1933 , just a year after G. W. Nichols had published in the Transactions of the American Electrochemical Society a study of making anodic manganese dioxide from solutions of manganous sulfate . The I. G. experiments were made to confirm the American work and were also extended to a larger scale . Only chemical purity was considered , and no mention is made of crystal form . The report adds to the knowledge submitted by Nichols but has not been previously available to the general public . Believing it of value to the United States industry , a translation has been made .

May 1, 1948

By Robert H. Bedford

As a result of the Bureau's general survey of quicksilver deposits in California, the Guadalupe mine area was among those chosen for exploration. Exploration, such as that at the Guadalupe, was aimed primarily at maintaining or increasing production of quicksilver during the critical wartime period. The project as originally planned contemplated sampling the dumps and prospecting some promising surface exposures by bulldozer trenches. Salvage was the objective in the first case and new ore in the second. Later, a program. of diamond drilling was added, designed to add both to ore reserves and to geological information. This report summarizes the history, notes the location and physical features, mentions property and ownership, and presents a brief description of the mine. The geology is outlined, and the work done by the Bureau of Mines is explained and supplemented with accompanying maps. The work involved repairing 1-1/4 miles of roads; bulldozing 13 trenches by removing 2,345 cubic yards of dumps to provide for sampling; digging and sampling 9,284 linear feet of hand trenches, digging and sampling numerous test pits; and drilling 7 diamond-drill holes, totaling 1,000 feet. A total of 419 samples, including 10 percent check samples, were taken. Exploration work in California at the time of this project was under the direction of Spangler Ricker, supervising engineer of the California field office, the late Robert Bedford was in charge of the fieldwork on this project.

Jan 1, 1950

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By H. L. Burmeister

This report describes the mining and milling practices used by the Eastern Magnesia Talc Co. at its Johnson, Vt., operation. The report also contains a description of the local geology and all available information on cost and performance data. Since 1925 the mine has produced continuously at an average annual rate of 54,000 tons, and the ratio of ore hoisted to finished product is roughly 2 to 1. Ore is stoped by a combination of shrinkage and sublevel methods. In any 24-hour period the mill produces an average total of 14 grades of finished talc product, 9 by dry grinding and air classification and 5 by wet grinding and flotation methods. The mine operates one shift per day, 5 days per week and the mill operates on a 3-shift, 5-1/2-day-per-week basis. Operating costs for 1958, on a percentage basis, were mining, 22.34; milling, 54.77; ore haulage, 2.89; and all other, 20.00 percent.

Jan 1, 1963

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By R. Karl Zipf, Z. T. Bieniawski

"Abstract. Based on the premise that understanding the fundamental mechanics of fine fragment formation in coal will lead to reducing coal dust problems in mines, a thorough study of the mechanics of crack propagation in coal was undertaken. Two approaches were considered in an attempt to understand and quantify the fracture process as it relates to fine fragment formation.In one approach, theoretical models are used which describe the size of the fracture process zone which may relate to the amount of structural damage and fine fragment formation on the new crack surface. The other approach is based on the relationship between crack tip stress intensity and new surface appearance for mixed mode crack propagation. Preliminary observations with a scanning electron microscope support the premise that fine fragment formation is related to fracture surface appearance and fracture initiation conditions.An experimental program designed to supply the input parameters for these approaches is presently underway. The experimentation features mixed mode fracture toughness testing, using a special mixed mode testing rig, and fracture velocity measurements with a crack propagation gage. The interpretation of this data via the approaches discussed will provide further understanding of the mechanics of fine fragment formation in coal."

Mar 1, 1989

By J. Roger Loebenstein

This report presents a U.S. Bureau of Mines study of the flow of arsenic-containing materials in the United States, based on the best data available in 1991, includes a consideration of arsenic as a byproduct of the processing of nonferrous metals, the fate of arsenic in manufacturing wastes, the quantity of arsenic used in products, tile fate of arsenic in dissipative uses, and the useful life of discarded products. Where possible, estimates are given of the amounts of arsenic lost from the materials flow. Arsenic byproduct of mining nonferrous metals. Historically, most U.S. production has been from the states of Montana, Washington, and Utah. The smelters in these states are believed to be the areas of the country where arsenic is most concentrated in the soil, tailings ponds, and waste dumps. Since the closure of the last domestic producer of arsenic in 1985, all arsenic has been derived from imported sources. Historically, arsenic was important in agricultural applications as an insecticide, herbicide, and cotton desiccant. As the environmental movement gained momentum and the toxicity of arsenic became better understood, most of the agricultural uses for arsenic were banned. Beginning about 1975, the use of arsenic as a wood preservative began to grow. After 1980, wood preservative uses became more important than agricultural applications. By 1990, 70% of the arsenic consumed in the United States was used by the wood preservative industry and 20% by the agricultural industry. The major source of domestic arsenic emissions in 1989 was from the U.S. copper processing indus¬try. About 7,800 mt/yr of arsenic was discarded in leach dumps, tailings, and slag. Another 800 mt/yr was liberated to the atmosphere and 1/100 mt/yr was exported in copper concentrates. On the consumption side, 9,200 mt/yr was lost, mostly from dissipative agricultural uses and the disposal of obsolete arsenical products.

Jan 1, 1994