Search Documents

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By Janet Torma-Krajewski, Pauline Lewis, Paul Gust, Lisa Steiner, Kean Johnson

Ergonomics processes described in the literature have been associated mostly with manufacturing, financial, electronics, and office settings where working conditions tend to be rather constant and repetitive. The information presented in this document demonstrates, however, that an ergonomics process can also be implemented in a setting such as mining where working conditions frequently change and workers are periodically exposed to extreme weather conditions. This document describes how Bridger Coal Company implemented an ergonomics process at its Jim Bridger Mine from 2001 through 2004. The process developed by the Ergonomics Committee, the promotion of the process to management and employees, and the impacts of the process on working conditions at the mine are reviewed. Barriers overcome and lessons learned are also described. Quotes from Bridger Coal Company employees are included in the document to add a personal perspective. Other industries with working conditions similar to mining, such as construction and agriculture, may find this information useful.

Jan 9, 2006

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are suitable chemically under present standards for producing metallurgical coke. (b) Which coals require special and more intensive treatment in preparation than is now practiced. (c) Which coals cannot be considered potential sources of metallurgical coke regardless of preparation. This report is one in a county series that describes the preparation characteristics of the coals of Mingo County, W. Va.

Jan 1, 1956

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By John W. Taber

Discovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits appear to be sharp-walled, low-angle-, tabular ore bodies in granite and are at least 10 feet thick. The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaF2 and 1.44 percent SiO2. Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3.

Jan 1, 1952

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By Oliver Bowles

Limestone, including dolomite, is the most widely used of all rocks - nearly 300 million tons annually in the United States alone. It occurs in some form in every State and is produced in thousands of localities. Because of its attractiveness, substantiality, and durability it is employed extensively as a building stone. In crushed and broken form it is used for concrete aggregate and railroad ballast and in highway construction, metallurgy, agriculture, and a host of chemical and industrial processes. This paper proposes to furnish general information on the origin and occurrence of limestone and dolomite, chief production centers, major uses, and methods of quarrying and preparing stone for market. Footnote references will guide the reader to sources of more complete information.

Jan 1, 1956

By V. A. Marple, K. L. Rubow, S. M. Behm

"An eight-stage cascade impactor, with cut-sizes ranging from 0.056 to 18 um at a flow rate of 30 L/min, has been developed, calibrated, and tested in field programs. This impactor, called a microorifice uniform deposit impactor, has several features not normally found in cascade impactors. Ultrafine particles as small as 0.056 um are collected while keeping the pressure drop moderate by utilizing multiple nozzles (up to 2000) as small as 52 um in diameter. At each stage the collected particles are deposited uniformly over the entire impaction plate by rotating the impaction plate relative to the nozzles and by the correct radial placement of the nozzles. The particle cutoff characteristics (collection efficiency curves) of each stage and inter-stage losses were determined by means of monodisperse aerosols. The cutoff characteristics were found to be sharp and similar for all stages.Inertial impactors are widely used for the size-selective collection of aerosol particles. One reason for their wide usage is that the principle of operation is simple: a jet of particle-laden air is directed at a flat impaction plate. Large particles are collected on the plate while smaller particles follow the airflow out of the impaction region and are not collected. The division between the size of particles collected and those that are not is quite sharp. Secondly, the particles in an impactor are classified by their aerodynamic diameter (an important size parameter in many fields of study, including those related to respirable particle health effects). Thirdly, it is easy to collect particles in discrete size ranges by passing the aerosol through a number of stages (one stage consisting of a nozzle and impaction plae) in series, with each subsequent stage collecting particles smaller than the one before it. This is known as a cascade impactor. Finally, impactors can classify particles over a wide range of particle sizes: as low as 0.005 um (Fernandez de la Mora et al., 1990) and as large as approximately 50 um (Vanderpool et al., 1987).This paper describes a general purpose cascade impactor that has been developed in our laboratory and used in a variety of studies including visibility studies (McMurry et al., 1986; McMurry and Zhang, 1989), underground mine studies (Marple et al., 1986; Rubow and Marple, 1988; Rubow et al., 1988), and general atmospheric pollution studies (Macias et al., 1981; Dzubay et al., 1984). The impactor, called a microorifice uniform deposit impactor (MOUDI model 100, MSP Corp., Minneapolis, Minn.), is the integration of two earlier impactor de¬velopments: the microorifice impactor (M01) (Kuhlmey et al., 1981) and the uniform deposit impactor (UDI) (Marple et al., 1981).The MOUDI has several features normally not found in other cascade impactors. These include collection of particles as small as 0.056 um in aerodynamic diameter with a moderate pressure drop, uniform particle collection on the impaction plates, inter-changeable impaction plates to allow for the plates to be easily and quickly changed in the field, and covers for these substrates to provide a means for safe storage and/or transport of the collected particles to the laboratory for analysis."

Mar 1, 1992

By Donald F. Smith

This report describes the construction and calibration of two ice calorimeters and includes results of high-temperature heat-content measurements, made by the Federal Bureau of Mines, on rubidium fluoride, hafnium tetrafluoride, cesium chloride, and cesium iodide. The heats and entropies of fusion of rubidium fluoride, cesium chloride, and cesium iodide have been calculated at their respective melting points using equations derived from the experimental heat-content data. Hafnium tetrafluoride did not melt within the range of temperatures investigated. Heat and entropy of transition of cesium chloride from the alpha to the beta form were also determined. INTRODUCTION Free-energy data usually afford the cheapest and quickest means of determining the feasibility of experimentally untested reactions. For known reactions, free-energy data show the variation of the equilibrium constant with temperature and make it possible to calculate, without experiment, the maximum ratio of product to raw material for a given chemical process.

Jan 1, 1961

By W. A. McKinney

Bureau of Mines Research has demonstrated that it is technically feasible to segregate oxidized copper ores by use of a direct-fired, refractory-lined rotary kiln. Previously, the segregation process had been effected only in much more complicated indirect-fired, stainless steel kilns, The method comprises heating crushed ore premixed with small quantities of salt and carbonaceous material, such as coke, to about 830° C to produce copper as fine flake and metallic films on the surface of the coke particles. After grinding of the cooled furnace calcines, the copper is recovered by conventional flotation. During direct-fired segregation it was necessary to closely control the air-gas mixture in the burner. Good copper recoveries were obtained only when adding air in the limited range of 1.15 to 1.2 times the theoretical amount required for combustion of the natural gas. Batch trials of the new technique on quartzite-, limestone-, sandstone-, and limonite-type oxidized copper ores containing from 1.4 to 6.2 percent copper yielded flotation concentrates containing from 3.7 to 45 percent copper, representing 84 to 95 percent recoveries. Analyses of the furnace gases showed that loss of copper by volatilization was negligible. The preliminary direct-firing segregation studies were complemented by continuous runs on the quartzite ore, containing 1.4 percent copper, in an integrated segregation-flotation pilot plant having a 60 pound-per-hour capacity. In a typical test, 84 percent of the copper was recovered in a cleaner flotation product containing 25 percent copper. The study will be continued to further delineate the conditions for good segregation as effective use of standard ceramic-lined kilns will render the process more attractive from a commercial standpoint.

Jan 1, 1963

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By Robert C. Dyni

This U.S. Bureau of Mines (USBM) report summarizes a field demonstration of pneumatic backfilling technologies conducted at the abandoned Hillside Coal and Iron Slope in Vandling, P A. Researchers demonstrated two pneumatic backfilling technologies recently developed under the USBM's Abandoned Mine Reclamation Research Program, the Pneumatic Pipefeeder and the High-Efficiency Ejector. Both systems had previously been evaluated at the USBM's subsidence abatement investigation laboratory near Fairchance, P A. The objective of the demonstration was to fill 100% of the abandoned tunnel with backfill stone to prevent further subsidence. The Pneumatic Pipefeeder was used for 21 days, at a rate of 63 to 124 t/ d (69 to 136 st/d), to fill 88% of the tunnel. The High-Efficiency Ejector was used for 2 days, at a rate of 125 to 132 t/d (138 to 146 st/d) to fill the remaining 12% of the tunnel. The backfill placed by both systems was tightly compacted. The major problem encountered was wear on the polyethylene pipeline from the abrasion of the high-velocity backfill. The use of heavier steel pipe minimized the problem. A cost analysis for the entire project is given.

Jan 1, 2010

By Henry C. Meeve

This report describes work done in the Creede Mining district, Mineral County, Colo., in 1965-66 as a part of a Bureau of Mines study of the silver production potential of the United States. The ruining history of the district is briefly covered, and representative former and current mining operations are described. Mining and milling costs of the Emperius Mining Company's operation are given in some detail as being representative of the cost of mining typical Creede ore bodies under current technology. An estimate of the silver reserves and resources of the district is presented, subject to many uncertainties stemming from inaccessibility of old workings, lack of mining records, and low level exploration activity, all of which limit the opportunity to accurately evaluate ore potential. The report concludes with an analysis of future silver production trends in the Creede district. An increase of silver production to as much as I million ounces yearly is projected, possibly starting in 1969. As long as ore bodies in the zone of enrichment, in which silver is a major constituent, contribute a substantial part of Creede production, silver price will affect overall production rates appreciably. As the richer are bodies become depleted, an increasing portion of production again will be coming from primary sulfide ores in which silver is a byproduct of lead and zinc. When this occurs, the level of silver production will be governed chiefly by lead and zinc production and prices and can be expected to decline to the 1960-66 level, which amounts to an average of 240,000 ounces per year.

Jan 1, 1968

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By J. E. Pahlman

Spontaneous oxidation and combustion of sulfides and resultant fires are serious problems in underground mines. The Bureau of Mines has con-ducted fundamental thermal gravimetric analysis (TGA) research to deter-mine the mechanisms and factors governing the rate of low-temperature pyrite oxidation, and to identify possible inhibitors to spontaneous oxidation and combustion. The mechanism of low-temperature pyrite oxidation was found to be topochemical, meaning that the oxidation process is controlled by the chemical reaction at the interface between pyrite (FeS2) and iron sulfate (FeS04)' An activation energy of 8.9 kcal/mol FeS2 was obtained for oxidation of minus 500-mesh pyrite in an atmosphere of 60 vol pct water vapor and 40 vol pct . Water-vapor content of the atmosphere was found to be the critical factor in the rate of spontaneous oxidation of pyrite, with a water-vapor content greater than 20 vol pct needed for accelerated oxidation. An atmosphere of pure oxygen resulted in negligible oxidation. The rate of pyrite oxidation is also greatly affected by the particle size of pyrite. Pyrite-oxidation rate increased drastically for particles less than 40 ~m. Room-temperature pyrophoric behavior was observed for freshly ground unoxidized pyrite (55 pct minus 5 ~m) upon exposure to air. Addition of water-adsorbing materials such as activated alumina (Alz03) decreased the rate of pyrite oxidation.

Jan 1, 1986

By Eugene T. Sheridan

The 25th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, disclosed that 79 companies produced and sold peat from 81 operations in 21 States in 1958. Peat is a carbonaceous deposit, formed under water or in a water-saturated environment from plant material. It is the first stage in the development of coal and, when properly dried, can be used as fuel. Although 98 percent (estimated) of the total world production is used for energy purposes, the status of peat in the United States is somewhat unique in that none is used for fuel, and practically all is consumed as an agricultural product, chiefly for soil improvement purposes. The domestic peat industry has expanded rapidly since World War II, and production in 1958 was 327,813 net tons valued at $3,445,767. More than one-half million ton of peat was consumed in the United State in 1958, however, as 269,096 tons was imported.

Jan 1, 1959

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996