Search Documents

By W. E. Webb

This report describes a method the Bureau of Mines devised for measuring the dielectric constant and loss tangent of low-loss minerals at microwave frequencies. Determina-tion of these properties makes it possible to predict the effects of using microwave heating in potential mineral processing applications. The method uses a test cell and radio-frequency (RF) impedance analyzer with automated data acquisition and analysis. In this initial phase of microwave heating research, the Bureau measured dielectric constants and loss tangents at frequencies between 100 MHz and 1 GHz. The objective was to establish a reliable data base for use in predicting the effects of microwave heating on minerals. Comparison with previously measured data showed the Bureau's measurement method to be accurate to within ± 3 pct. This report describes the method and discusses the preliminary results of the Bureau's investigations. Typical comparative data are included.

Jan 1, 1986

By W. A. Selvig

"The tests described in this paper were conducted under the sponsorship of Subcommittee VII on Pulverizing Characteristics of Coal, a subcommittee of Committee D-5 on Coal and Coke, American Society for Testing Materials, with a view to evaluating various laboratory procedures for testing grindability of coal in connection with commercial pulverization of coal for use as powdered fuel. The subcommittee, at a meeting in New York City on February 21, 1934, selected for test four methods that had been developed during the past few years for testing grindabilitay of coal and were being used by coal-testing laboratories in the United States and Canada. These methods are:Bureau of Mines method, Cross method, Fuel Research Laboratory method, and Hardgrove method. Subcommittee VII agreed that the grindability tests should be made on five coals selected to cover a wide range of hardness. The Pittsburgh Experiment Station, Bureau of Mines, was asked to direct the investigation and to prepare representative samples of the coals. Laboratories of the fol. lowing institutions and companies agreed to cooperate by making grindability tests: Babcock & Wilcox Co., Foster Wheeler Corporation, Fuel Engineering Co., of New York, Fuel Research Laboratory of the Canada Department of Mines, and Northwest Experiment Station of the Bureau of Mines.ACKNOWLEDGMENTSHelpful suggestions in planning the investigation were made by A. C. Fieldner, chairman, Committee D-5 on Coal and Coke, A.S.T.M., and chief engineer, Experiment Stations Division, U. S. Bureau of Mines, Washington, D. C., and E. B. Ricketts, research engineer, New York Edison Co., New. York City.The coal samples were supplied through the courtesy of floats, Wheeler Corporation, New York City; Philadelphia & Reading Coal & Iron Co., Pottsville, Pa.; Pittsburgh Coal Co., Pittsburgh, Pa.; and Pocahontas Fuel Co., Inc., New York City."

Feb 1, 1936

By F. E. Block

The metallic reduction of vanadium chlorides was investigated by the Federal Bureau of Mines as a possible new route for preparing vanadium metal in an effort to develop a production process that would be adaptable to large-scale plant production and would yield metal of uniformly high quality. Vanadium tetrachloride was usually prepared by chlorinating vanadium pentoxide in the presence of carbon. Although oxygen-?free tetrachloride was difficult to prepare this way, it could be prepared by the direct chlorination of vanadium carbide. Lower valent vanadium trichloride was prepared by the thermal decomposition of vanadium tetrachloride. Vanadium dichloride was also prepared by the thermal disproportionation of vanadium trichloride.

Jan 1, 1961

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

By P. L. Sibrell

Electrorefining of Ti in nonaqueous solvents has been studied by the U.S. Bureau of mines as a method for recycling impure scrap Ti. Electrochemical behavior of Ti species was investigated using cyclic voltammetry. Research results showed that Ti metal can be dissolved in polar solvents such as dimethylformamide or dimethyl sulfoxide. However, deposition of Ti from these solvents was not successful. Several solvent systems were investigated for electrodeposition of Ti but no deposits were obtained. Reduction of Ti4+ complexes to Ti3+ proved to be straightforward, but reduction to lower oxidation states could not be confirmed. In dimethylformamide solutions, cyclic voltammetry results demonstrated the reduction of Ti to an oxidation state of less than three, but no Ti metal was identified. In dimethyl sulfoxide solutions containing LiCl, it was possible to deposit Li metal. After adding Ti salts to the solution, electrolysis quickly passivated the electrode. Deposition of Ti was also investigated in solutions of dimethoxyethane and propylene carbonate but, again, no reduction of Ti to oxidation states of less than three occurred. Therefore, the prospects for a nonaqueous electrorefining system for Ti metal do not appear promising.

Jan 1, 2010

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

By W. H. Coghill, F. D. DeVaney

"Introduction Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with no many ""inflection points"" and ""counterflexures"" that they obscure the issue.Some of the investigators have neglected the very essence of the problem, namely, the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration.Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.Grindability Characteristics When the ores are being studied the information sought is grindability characteristics (grain-size distribution) and the grindability (work required to produce new surface) of a group of ores.When the study is of the machines, several machines are used for a given ore or given types of ores, and the grinding performances of the machines are compared by a grain-size study.Table 1 gives the grindability characteristics and grindability of six substances, one of which is coal. The substances are arranged from left to right in progressing order of tons per horsepower-hour. Curves and graphs are not needed for elucidation. The secret of the ease of interpretation is the order mentioned and the similarity of the sizing analyses. Power records must be complete in grinding studies.The grinding device was a ball, plunger, and mortar called the drop weight.' It may be used to advantage when the amount of material to be tested is too small for the orthodox machines.The upper part of table 1 shows the grindability characteristics by the cumulative-sizing analyses. Note how closely the percentage weights agree for a given sieve size. The lower part shows the grindability in terms defined elsewhere. The present paper should be read in conjunction with that paper."

Jun 1, 1934

By Robert H. Peters

This report presents findings from a Bureau of Mines study on barriers that may prevent miners from correcting and avoiding groundfall hazards. Such barriers stem from four basic types of problems: (1) inability to recognize groundfall hazards, (2) inability to correct groundfall hazards, (3) lack of motivation to search for groundfall hazards, and (4) lack of motivation to correct groundfall hazards. Data are presented that summarize the views of miners, section supervisors, and mine inspectors about the contribution of these barriers to groundfall accidents and what they think should be done to reduce the frequency of injuries sustained by falls of roof and rib. The report also includes a summary of miners' responses concerning their recent experiences with groundfall accidents, along with industrywide statistics on accidents and injuries caused by ground falls in underground coal mines.

Jan 1, 1987

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal, (2) to upgrade marginal coals through effective preparation, and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the seventh of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Floyd County, KY., which comprises parts of the Paintsville, Prestonsburg, Harold, Hindman, and Pikeville quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all avail-able data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By W. J. Kroll

This report on the bibliography of zirconium has been confined to those publications and patents that appear to be useful in the commercial development of the metal, both the malleable and the nonmalleable. The methods of production have been stressed and special attention has been given to the alloys. Compounds of importance, like the oxide and chloride, for the manufacture of the metal or of the alloys have been considered. The use of the oxide in refractories anal in the glass and porcelain industries has been omitted. The present survey is critical; that is to say, an attempt has been made to evaluate the effectiveness of suggestions made in the literature. The exhaustive work of Marden and Richy, Bureau of Mines Bulletin 186, published in 1921, has been taken as a base to start from with the intention of bringing the subject up to date with material published in the last 24 years. During this time there was considerable 'advance in the preparation of the metal and Its alloys, and in the development of new uses. On the other hand, there was little progress in the methods of decomposing the ores, so that the chapter on this latter phase is necessarily short.

Jan 1, 1946

By Timothy Y. Yen

This Bureau of Mines report evaluates audio dosimeters, 3 sample units from each of 10 currently marketed brands. Each dosimeter was treated as a "black box" with the acoustic stimulus as the input and the accumulated dosage as the output. The dosimeter microphones were exposed to a sound field gener¬ated in an anechoic chamber. Characteristics evaluated include frequency response (100 to 8,000 Hz), level-time trade-off rate (88 to 117 db), status of calibration, crest-handling capability, and power consumption rate. Experi¬mental errors revealed by replication of the tests were found to be generally much smaller than variations in performance among the samples of any brand, and possibilities of further reducing the magnitude of these errors are discussed.

Jan 1, 1977

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By Martin Hertzberg

A comprehensive study of the flammability behavior of air-dispersed coal dust was made using an 8-liter Bureau of Mines system which included the following: (1) An optical probe to continuously monitor the dust concentration; (2) measurements of ignition energy requirements; (3) the use of several narrow size distributions ranging from 3 to 65 µm in average diameter; (4) measurements of the extent of flame propagation based on pressure attained at constant volume, residual O2 content after combustion, and flame and dust surface temperatures. The measured lean limit for near-horizontal propagation of Pittsburgh coal dust was about 135 mg/l (milligrams per liter), virtually independent of particle size. Required ignition energies were hundreds of joules and measured limit flame temperatures were 1,450 to 1,600° K. Data on inerting? requirements with KHC03, rock dust, and NaC1 gave approximately the same results as full-scale explosion tests. The good agreement suggests that the cause of earlier discrepancies between small-scale laboratory data and full-scale mine experiments may not have been the difference in size, but were rather a problem of proper care in isolating and controlling the significant experimental variables and in consistently defining the extent of flame propagation at the limits.

Jan 1, 1979

By R. J. Leary

Oxidation testing of copper-clad steel strip was performed in a muffle furnace to determine whether copper in contact with steel scrap could be removed by oxidation in an airstream at high temperatures. Substantially all of the copper was oxidized before any significant iron oxidation occurred. The rate of copper oxidation was not affected by contact with iron. Copper oxide scale separated spontaneously from the underlying metal during cooling. Results indicate the possibility of removing light-gage copper coatings and components from ferrous scrap by oxidation in an incineration process.

Jan 1, 1965

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938