Search Documents

By W. H. Oppelt

The Federal Bureau of Mines investigated combustion of lignite in domes-tic heating equipment to obtain information on equipment performance and to evaluate testing procedures. Three types of domestic heating equipment were tested, ranging from a hand-tilled, magazine-type space heater to a ram-type overfeed stoker. Lignite was readily burned in each of the three units under various test conditions. Burnoff rates determined by adding weighed charges to the magazine were found to be in error because of shrinkage of the lignite when only a portion of the magazine capacity was consumed during a test. More reliable burnoff rates could be determined by carbon-nitrogen balances. A hand-fired magazine-type space heater (Booker heater) was operated without the furnace attachment at efficiencies to 75 pct. One test series was run with minimum supervision under conditions encountered in actual household operation. No mechanical trouble was encountered.

Jan 1, 1960

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By Ludwig Schmidt

The economic value of reducing the evaporation losses of crude oil and of gasoline is so well founded that the petroleum industry is constantly seeking new and improved storage tanks and methods of handling its products to further reduce these losses. A comparison of the methods and apparatus used in handling and storing crude oil and its products today with those in general use 10 years ago would show that an oil tank is no longer simply a container for holding liquid, but is now considered an important piece of equipment which if, subjected to constant inspection and care. In fact, the modern vapor-tight tank often requires as much care as a boiler or pump when one considers Its various component parts such as vapor-tight gage hatches and thief-hole covers, vacuum and pressure relief valves, swing line apparatus, vapor-recovery systems, insulation, cooling devices, and often automatic gaging devices. As an auxiliary to the physical equipment of the tank itself the subject of paints and paint colors is now given considerable attention. In addition to vapor-tight tanks and auxiliary equipment, other types of tanks for reducing, evaporation which are new to the industry have also been developed and placed on the market within the past few years. The development of the floating roof type was an innovation in tank construction, directed toward the reducing of evaporation losses. This type of roof rides on the surface of the oil and thus eliminates all vapor space. It is especially valuable for working tanks.3 A recent development in tank construction is a new type of tank roof known as the diaphragm or "breather roof," Which practically eliminates the movement of air-vapor mixture from a storage tank filled with oil. It is of especial value for use on tanks in which oil is stored over long periods.

Jan 1, 1930

The content of the book covers: (1) The theory of the Eötvös torsion balance; derivation of the working formulas; description of the instrument; method of observation; relation of the magnitudes observed to the lines of force and the level surfaces of gravity; corrections or normal effects, near and distance terrane; subterranean effects; effects due to certain mathematical bodies. (2) Notes on the practical employment of the Eötvös torsion balance; initial testing of the instrument and of accessories; hints on planning the survey; work at the station site; office computation and plotting of results; the interpretation of the results: (3) A description of the instrument and instructions for its manipulation. This book was the best discussion in English on the theory and use of the Eötvös torsion balance and is surpassed only by a later paper by the same authors that covers much of the same ground. The book is suitable for a textbook for beginners, and advanced students will find it of use. It should be available as a reference book in all geological libraries and in all torsion balance department offices.

Jan 1, 1929

By K. K. Kelley, W. W. Weller

Heat capacity measurements of lead molybdate and lead tungstate were conducted over the temperature range from 51 ° to 298 ° K. The entropies were found to be S298.15 = 39.7 ± 0.5 cal / deg mole for lead molybdate and S298.15 = 40.2 ± 0.5 cal / deg mole for lead tungstate . The entropy values were combined with other pertinent data to obtain the entropies of formation of the two compounds from their constituent elements and oxides .

Jan 1, 1964

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By Wilder D. Foster

In the method used in the Health Branch of the Bureau of Mines for petro-graphic identification of the minerals in a rock, the sample is crushed, ground to a fine powder in a mortar, the powder is put on a slide, a drop of index oil and a cover slip are added, and the slide is ready for examination. The rock should be ground fine enough so that most of the particles consist of only one mineral, otherwise identification is difficult. Finally, the amounts of the minerals present in the sample are estimated to the nearest 5 or 10 percent. When quartz grains are mixed with some claylike minerals) of which by far the most common example is quartz and kaolinite in a shale, grinding in a mortar does not always separate the quartz from the kaolinite; instead, the quartz grains become coated with the kaolinite and are not visible, even after careful search. Talc acts Similarly, but muscovite and pyrophyllite do not. In evaluating the possible silicosis hazard of breathing dust from a shale, it is essential to be able to see and identify all of the quartz grains, as the other minerals present are relatively innocuous.

Jan 1, 1949

By P. G. Clites

The Bureau of Mines developed techniques for induction melting of titanium in a split, water-cooled copper crucible. Calcium fluoride, which was used as an inert slag cover during melting, formed an insulating layer of solid slag between the ingot and the crucible wall. This thin layer of slag effectively insulated the ingot from the crucible and prevented the molten metal from shorting across the slits between adjacent segments of the crucible. The technique provides a means of melting loose titanium sponge and scrap and eliminates the need for fabricating a consumable electrode. This report describes the equipment developed and compares ingots produced from two varieties of titanium sponge, from titanium scrap, and from previously melted titanium with ingots prepared by vacuum-arc melting and electroslag melting. A melting scheme was also proposed and evaluated whereby loose titanium sponge was consolidated into a first-melt ingot for vacuum-arc remelting.

Jan 1, 1969

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By Roy E. Peterson

The Bureau of Mines has been developing and evaluating methods for beneficiating the large deposits of nonmagnetic (oxidized) taconite located on the western Mesabi Range. In this segment of the research, a sample representing about 0.5 billion tons of nonmagnetic taconite from near Grand Rapids, Minn., was beneficiated using a reduction roasting, magnetic separation, flotation process. The sample contained 32.1 pct iron and 49.1 pct silica. Tests were conducted both on a bench scale and with a 1,000-lb/h pilot plant. In the bench-scale research a con-centrate containing 69.0 pct iron and 4.5 pct silica was produced with an iron recovery of 82.1 pct. In the pilot plant, reduction roasting was conducted in a 35-ft kiln using lignite as the reductant and major source of fuel. Dust from the kiln exhaust was pelletized and recycled to the kiln. The roasted taconite was beneficiated by magnetic sep-aration and flotation to produce a product containing 67.9 pct iron, 5.5 pct silica, and 69.7 pct of the iron in the kiln feed. The cyclone separation in the grinding circuit was sharpened by demagnetizing the cyclone feed in a 400-Hz, 1,000-Oe magnetic field.

Jan 1, 1983

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

China?s New Steel Complex Postponed. - The planned $5 billion Baoshan Steel Works near Shanghai is being laid aside for 6 months to a year, and may be abandoned altogether. The second phase of construction, in which Wean United, Inc., of Pittsburgh was a major participant, has definitely been cancelled. Over $1 billion had been committed to the 6 million-ton-per-year plant. U.S. Firm Develops South African Fluorspar. - The Armco Bronne Co. of Middletown, Ohio, plans to spend $27 million to develop a fluorspar mine in the Republic of South Africa, With fluorspar reserves at 20 million metric tons, the project is planned to produce 200,000 tons Per year of fluorspar for export starting in 1983. U.S.S.R. Resumes Sales of Titanium Sponge. - Against a background of increased U.S. titanium sponge supplies, the Soviet Union is offering limited quantities of this commodity to the U.S. market at approximately $10.00 per pound, down from $25.00 per pound last year.

Jan 1, 1981

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about 1/2-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15. 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black. Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By Holmes, George H. Jr.

The Cherry Creek tungsten district was explored by the Bureau of Mines from April 16 to August 13, 1942. This district is in north-central White Pine County, Nev., 50 miles north of Ely. Principal work was done on the property of the Cherry Creek Tungsten Mining Co. and at the adjacent Chance mine, although the entire district was examined and mapped. The exploratory work was done in cooperation with the Federal Geological Survey and comprised surveying, trenching, sampling, long-hole and core drilling, rehabilitation of mine workings, road building, drifting, and shaft sinking. The more important tungsten occurrences were explored by trenching and diamond drilling. Sixteen holes, having a total length of 2,515 feet, were drilled. The project resulted in partial development of three new tungsten deposits and small increases in the reserve tonnage of two scheelite-bearing lenses that were being mined by the company. The following pages summarize the history of the district, outline the ownership of the properties explored, and describe the physical features and mineral deposits. Mining and milling practices at the Cherry Creek tungsten mine are outlined, and the plan and results of project work are presented in detail together with surface maps, assay maps, and drill-hole logs.

Jan 1, 1950

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By Cleo G. Rall

The value of brine analyses in the study of petroleum-engineering problems was recognized early in the history of petroleum. The Bureau of Mines before 1928 had indicated in several reports.3/ ways in which analyses might be used. Because of the confusion resulting from attempts to correlate the work of different chemists using greatly varying methods of analysis and systems of computation and expression of results, a paper presenting the methods used by the Bureau of Mines was prepared and published in 1928. This system of determining the characteristic constituents of oil-field waters and of calculating and reporting results has been widely adopted by the petroleum industry. The earliest and most obvious use of water analyses is determination of the source of water infiltrating into petroleum and natural-gas wells. For this purpose it is necessary that an analysis of the connate water of the formation from which the oil is produced be available and that an analysis of the contaminated water be made. By comparing these analyses with those of connate waters from formations higher in the structure, the formation from which the infiltrating water comes may be identified.

Jan 1, 1953

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983