Search Documents

By Curt D. Jr. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to Forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State's refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State's petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

By J. R. Thoenen

This circular is part 2 of the third subject (entitled "Excavation") of a series summarizing; the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes. This paper discusses the use of the power scraper, slackline cableway excavator, and hydraulic monitor, and part 3 will discuss the use of various types of dredges. Subsequent papers in the series will discuss the use of haulage equipment, the application of both excavating and haulage equipment to various types of deposits, and operating costs. THE POWER SCRAPER The power scraper is a younger member of the various forms of gravel excavators. It is a mechanized enlargement of the slip scraper and other scrapers which depend upon animals for power and has a greater range of operation from a single set-up than any other excavation unit except the slackline cableway excavator.

Jan 1, 1935

By Bruce Maxwell

The deformation modulus of coal mine pillars theoretically can be reduced by drilling holes in advance of the mining face. This reduction of modulus along the edge of the pillar has the effect of decreasing the stress concentration in the roof; control of roof caving is thereby predicted. Initial field work indicated that a high horizontal stress field existed at the field test site: Subsequent field work was undertaken to confirm the high horizontal stress field and to attempt to relieve the horizontal stress in the immediate roof. A method of softening pillars in conjunction with normal mining activity was developed. Instruments to measure horizontal roof strain, roof parting, roof tilt at the rib, and changes in vertical and horizontal stress in the roof and in the coal were used. These instruments were installed in both softened and unsoftened entries and in locations to indicate the effect of vertical slots in the roof. Significant stress reduction due to pillar softening was indicated, but the effect of this reduction on roof stability was not established. The vertical roof slots relieved the horizontal stress in the immediate roof very effectively, and observations of roof conditions indicated that the slots definitely improved roof stability.

Jan 1, 1977

By D. L. Bickel

This report presents a Bureau of Mines study intended to determine if horizontal stress trends exist and if the stresses can be projected for improved mine design in a selected coalfield. The horizontal stresses were determined in three mines in the Yampa Coalfield and one mine in the adjacent Danforth Hills Coalfield of northwestern Colorado. Stresses were determined from stress-relief measurements using a three-component borehole deformation gauge and overcoring techniques developed by the Bureau. A least-squares method of calculating the average rock stress components in the horizontal plane was performed. Physical properties of the rock from the test sites are also included. For the Yampa Coalfield, the maximum horizontal compressive stress in the floor ranged from 363 to 1,956 psi, and the maximum horizontal compressive stress in the roof ranged from 235 to 875 psi. For the Dan-forth Hills Coalfield, the maximum horizontal compressive stress in the floor ranged from 360 to 1,494 psi, and the maximum horizontal compres-sive stress in the roof was 1,033 psi. Results indicated a trend of low horizontal stresses in the Yampa Coalfield that have not impacted ground control conditions in mines less than 1,000 ft deep.

Jan 1, 1988

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962

By W. L. Crentz

In Fayette County, the Pittsburgh bed has been the major source of production for almost two centuries. Although historical documentation is not available, there is evidence, that the Pittsburgh bed may have been discovered in Fayette County near Mt. Braddock, Pa., as early as 1753. The earliest known reference to coal in western Pennsylvania was recorded in 1758 by a Quaker trader, James .Kenny, who reported having seen coal in Fayette County. The production of coke from Pittsburgh coal was begun in 1841, when two 10-foot beehive ovens were erected in the Connellsville region to make coke .for shipment by river to the market. The Connellsville, region extends from Latrobe, Pa., in Westmoreland County to South of Uniontown, in Fayette County. Connellsville coke was used with great success in the Clinton furnace in 1859.

Jan 1, 1951

By L. F. Willmott

The Bureau of Mines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipeline for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By J. M. Riley

The Bureau of Mines investigated a promising new technology for recovering A1203 from alunite to support the Bureau's alumina miniplant project. Results are presented for a study of the technical feasibility of treating alunite crushing and grinding reject fines for recovery of A1203. Alunite pellets having sufficient strength and resistance to degradation were produced by combining fines and coarse alunite with a KOH binder. The best pellets were prepared, in a laboratory pelletizer, by adding 1 pct KOH as a 5-pct solution to a mixture of 40 pct alunite dust (98 pct minus 65 mesh) and 60 pct coarse alunite (minus 20 plus 65 mesh). Calcines suitable for K2SO4 and A1203 recovery were produced by reducing dehydrated alunite pellets with sulfur in a laboratory shaft furnace for 4 h at 600° C, followed by air oxidation of the reduced calcine for 1 h at 600° C. This report presents design calculations, schematic diagrams, and discussions of the essential features of a proposed process research unit (PRU)--a continuous, 6-lb/h alunite shaft furnace--for studying the process.

Jan 1, 1983

By Grace N. Broderick

U.S. supply and demand data for coal, by States and regions, were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the coal industry that can be integrated into State and regional energy balances by source, form, and consumer sectors, and used for estimates of interstate and interregional energy flows. The tables give an estimated total supply of coal available for consumption, and also report the distribution of the supply among the major consuming sectors (household and, commercial, industrial, transportation, and electricity generation). To enable comparison of coal data with those for other energy forms, tonnages were converted to British thermal units (Btu). Future energy analysis studies could be facilitated by changes in the categorization of information collected on the coal industry. The data shown are based primarily on Bureau of Mines source material.

Jan 1, 1969

By George C. Branner

This circular is concerned with eight nonferrous scrap metals as they generated, collected, prepared, and consumed in California. Brief reference also is included with respect to Nevada and Hawaii. Four of these scrap metals - copper, lead, aluminum, and zinc - are of major importance and make up about 95 percent of the total value, whereas the remaining four - antimony, magnesium, nickel, and tin - make up the remaining 5 percent. For convenience, the subject matter is divided into three parts, (1) Data with respect to the collection, preparation, and marketing practices that are common activities to all the nonferrous scrap metals; (2) separate discussions and statistical data with respect to each of the eight nonferrous scrap metals in California; and (3) data with respect to Nevada and Hawaii.

Jan 1, 1962

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By W. W. Agey

Under terms of cooperative agreements, the Federal Bureau of Mines Inter-mountain Experiment Station assisted the General Services Administration (GSA) in operating the manganese-ore purchasing depots at Deming. N. Mex., and Wenden, Ariz. A resident metallurgist stationed at the depots directed sampling of the ore lots for assaying, took samples for amenability testing, calculated acceptances for payments to shippers, and served as technical adviser to the depot manager. The Intermountain Experiment Station at Salt Lake City, Utah, tested the amenability of the ores to determine how much of the manganese could be recovered in concentrates assaying a minimum of 40 percent manganese (Mn) and containing a maximum of 16 percent iron (Fe), 15 percent silica (Si02) plus alumina (AI203), 0.3 percent phosphorus (P), and I percent copper (Cu) plus lead (Pb) plus zinc (Zn). All chemical analyses of the ores and test products were done at Salt Lake City. In all, 567 ore lots submitted to the Deming depot were tested by flotation to determine their amenability to concentration into specification-grade material; 421 lots were amenable, and 146 were unamenable, primarily because of high copper content or excessive silica or iron in the flotation concentrate. Chemical analyses totaling 42,700 were made on the ores submitted to the Deming depot and on the products of the amenability-test program.

Jan 1, 1959

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

By G. J. Slavens

The U.S. Bureau of Mines conducted research on preparing submicrometer titanium nitride (TiN) powder as a substitute for tungsten carbide (WC) in cutting tools and wear-resistant parts. Earlier research on a small scale was expanded to include a larger reactor. The TiN powder was produced by contacting titanium tetrachloride (TiCI4) with anhydrous ammonia (NH3) in the presence of Mg at 1,100° C. The powder was collected in an electrostatic precipitator (ESP) filled with ultra-high-purity (UHP) Ar. All collected powder was thermal vacuum distilled to remove Mg and magnesium chloride (MgCl2), leaving the purified TiN. Powder handling and purification procedures were conducted to assure low oxygen content in the powder product. Oxygen content in the distilled TiN powder product was as low as 0.40 wt pct. Nitrogen averaged near 22.0 wt pet with a high of 22.4 wt pct. The purified powder product had an average median particle diameter of 0.14 µm with a standard deviation of 0.09 µm.

Jan 1, 2010

By V. A. Danielson

The Bureau of Mines studied waste disposal methods a1 a coal mine in Kentucky and another in Alabama to develop cost estimates, to provide better knowledge of current practices, and to guide consideration of alternate disposal methods. Costs of the existing waste disposal systems at each mine were estimated using present-day costs of equipment and labor. Costs of waste disposal systems using alternate equipment were also estimated. Although total disposal costs were essentially the same for both operations, reclamation costs will differ because of different reclamation practices.

Jan 1, 1969

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By F. W. Horton

Investigation of an extensive deposit of chromite-bearing actinolite-talc schist situated on the summit of Casper Mountain, 10 miles south of Casper, Wyo., was one of the first projects Undertaken by the Bureau of Mines under the Strategic Materials Act (Public 117, 76th Cong., Ch. 190, 1st sess.), for which an appropriation became available August 9, 1939. During the previous summer; the Geological Survey? made? a magnetometrical survey of the area in which the schist occurred. It was exposed in several small lenses and two larger ones aggregating about 19?acres in area. Although the occurrence of chromite here had been known for many years, the only work done on the deposit was the digging of? a few shallow pits on some of the more promising outcrops. From August 23 to December 3, 1939, the Bureau of Mines investigated the larger of the two main schist bodies. Twenty-four trenches having a total length of 8,073 feet were dug across the deposit, and its subsurface extension was explored by 3,623 feet of diamond drilling. Over 32 tons of samples were shipped to the Metallurgical Division of the Bureau of Mines at Reno, Nev., for reduction, analysis, and ore testing. In all, there were 853 individual samples. Geological maps, based upon examination of outcrops, trenches, and drill cores, as well as a contour map of the area were made by the Geological Survey.

Jan 1, 1949

By R. E. Heithecker

The Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalkrock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I.

Jan 1, 1934

By James S. Grichar

Interest in mergers in the nonfuel mineral industry developed when 5 were listed among the 50 highest valued mergers in the United States in 1981. This report presents a Bureau of Mines study of trends in merger activity from 1960 to 1979 and explores motives for mergers in the nonfuel mining and mineral industry. The objective was to determine precedent for or a trend toward the 1981 acceleration in merger activity and to examine certain financial motives for non fuel mineral mergers. Data indicate that the relative value of non fuel mineral mergers has grown since 1972 although the number of mergers has remained proportionate to historical trends for all mergers. Since 1974, the assets acquired in "large," nonfuel mineral firm mergers, those of $10 million or more, have comprised at least 93 pct of assets acquired. More nonfuel mineral firm mergers involved mineral companies as the acquiring firm than vice versa but mining and minerals firms acquired were of higher value than nonmining firms. A major motivation for mergers involving large mineral firms was the acquisition of assets at less than replacement costs. Univariate statistical testing, a methodology chosen for its applicability to the data, confirms this hypothesis while rejecting other financial motives. The remainder of the work is devoted to a discussion of suggested areas for future study.

Jan 1, 1984

By Richard W. Lewis

Domestic production of greensand (glauconite) increased 15 percent in quantity and 13 percent in value compared with that of 1964. Since only two firms were in operation, statistics on production and sales for the year are not reported in order to avoid disclosure of individual company confidental data. The average annual production for the 5-year period 1961-65 was 4,306 tons valued at $200,200. The material was marketed for use as a soil conditioner and a water softener. An article of mineralogical interest was published concerning the New Zealand glauconites.2

Jan 1, 1966