Search Documents

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By Leo A. Schrider

A prediction for oil recovery from a pilot waterflood in the Kane oil- field, located in Elk, Forest, and McKean Counties, Pa., was made and compared to actual field performance. Water-injection and production histories, well logs, other field data, and results from laboratory tests of core material were used in this analysis. Performance of the pilot waterflood, initiated in January 1963, was predicted using a modified Craig, Geffen, and Morse calculation technique. Maximum recovery from this low permeable, preferentially oil-wet formation was predicted to be about 22,500 barrels of oil after 300,000 barrels of water had been injected into the pilot waterflood area. After additional field data were collected it became necessary to reevaluate the pilot waterflood area. The gas saturation prior to the waterflood was estimated to have been 20 percent, based on an assumption regarding the required volume of water injected to initiate oil production. In view of the actual field performance, a gas saturation of 13 percent is indicated. When this gas saturation and the method originally proposed by Craig and others are used) the predicted results are more representative. In December 1965, field performance was further analyzed using a hyperbolic-decline curve as presented by Arps. Based upon this evaluation method, the pilot water flood in the Kane sand should produce 37,000 to 42,000 barrels of oil with the injection of 300,000 barrels of water into the pattern. By continuing this secondary-recovery project to a reasonable economic limit, ultimate oil recovery may be as much as 50,000 to 55,000 barrels, or 129 to 142 barrels per acre-foot from 36.5 acres.

Jan 1, 1967

By Paul C. McWilliams

This Bureau of Mines report analyzes data on the physical properties of quartzite rock from the Crescent mine, Coeur d?Alene mining district, Kellogg, Idaho, to demonstrate the use of multivariate techniques. After regression, factor, component, cluster, and discriminant analyses are discussed, these techniques are applied to the Crescent mine data. Three appendixes contain some of the required mathematical and statistical detail plus heuristic examples of three multivariate techniques --component, cluster, and discriminant analysis.

Jan 1, 1978

By Jeffrey A. Shibe

A prototype Fire Safety Evaluation System has been developed and is ready to be evaluated by a Peer Consulting Panel and for performing field tests. The system can be used to determine combinations of widely accepted fire safety equipment and under-ground coal mine features that provide a level of safety equivalent to those required by the Code of Federal Regulations-Title 30 for underground coal mines. In this evaluation, equivalent safety performance is gauged in terms of overall level of safety provided rather than by a component by component comparison.

Jan 1, 1987

By W. W. Adams

Two important facts stand out as features of the metal- and nonmetal-mining4 industry of the United States in 1941 as compared with 1940: First, the number of employees and man-days of employment increased; second, accident-frequency rates, both fatal and nonfatal, decreased. Reports from mining companies to the Bureau of Mines covering underground, open-pit, and surface operations for 1941 re¬vealed the largest number of men employed since 1926 and the largest number of man-days worked since 1929. The combined fatal and non¬fatal accident-frequency rate for 1941, calculated on a basis of one mil¬lion man-hours of exposure to hazard, was (except for 1931 and 1932) the lowest since 1911, the earliest year for which figures are available. During this 31-year period, only 1938 and 1939 showed lower fatality rates, and only 1931 and 1932 had lower nonfatal-injury rates. Operating companies reported that 9,620 mines were active during all or some part of the year. These employed 125,290 men, an increase of more than 4 percent over 1940. The total volume of work performed at all mines, measured in terms of man-shifts, increased to nearly 32 million, a gain of 10 percent; man-hours of employment rose to almost 254 million, an increase of 10 percent over the 231 million man-hours worked in the previous year. The year's operations resulted in an average work-year of 255 days per man, an increase of 13 days per employee over the average working time in 1940. Although the 8-hour day prevails generally at most mines, the industry as a whole averaged 7.94 hours per shift, as in 1940.

Jan 1, 1944

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By C. E. Wicks, F. E. Block, F. D. Stevenson

The vapor pressures of tungsten (VI ) chloride ( WC1 ) and hafnium ( IV ) iodide ( HFI ) were measured by a metal diaphragm technique . Vapor pressure values were obtained to permit calculation of the thermodynamic properties of the vaporization processes of the compounds . The vapor pressure data of WC16 are represented by the following equations for the liquid , B - solid , and a- solid over the temperature intervals indicated : - log P = 8.194 3,253 /T Liquid , 281.5 ° to 325 ° C : B - solid 230.0 ° to 281.5 ° C : log P a - solid 185.0 ° to 230.0 ° C : log Pam *** = 8.794 - 3,588 / T = 9.615 - 3,996 /T where T is the absolute temperature in degrees Kelvin . The heats of vaporization and sublimation are 14.9 , 16.4 , and 18.3 kcal / g mole , respectively . The entropy of vaporization at the normal boiling point , 330 ° C , was 24.3 eu . The fusion temperature , 281.5 ° C , and transition temperatures , 230.0 ° and 185 ° C , were found by thermal analysis .

Jan 1, 1964

By Ralph Husack

The Bureau of Mines investigated the effect of gamma radiation on reactions between Pennsylvania anthracite and fluorine and chlorine. In the tests with fluorine about 90 percent of the coal reacted at 350° C to form volatile products whether or not irradiation was employed. Up to 0.8 ml of liquid products per gram of anthracite was collected. Among the 25 com-pounds indicated by gas chromatography, fluoroform and l,l-difluoroethylene were tentatively identified from their relative retention times and perfluoro-cyclopentane from its infrared spectrum. In addition, a clear, hard, wax, probably a fluorocarbon, was formed at 45° C in both the presence and absence of radiation. With chlorine there was no significant difference due to radiation, and preliminary tests indicated that the chlorine reacted more with the organic matter of anthracite at 200° C than with inorganic matter. At 400° C the results were inconclusive because of excessive corrosion in the reaction vessel.

Jan 1, 1966

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By R. L. Grant

During the last decade or more , experimental research on commercial detonators used for initiating the detonation of dynamite and other high explosives has led to important improvements . Developments , especially in the United States , have been directed toward improvement in the construction of detonators to make them safer to manufacture and use . More suitable and safer initiating charges also have been found . Although for many years mercury fulminate was unrivaled as the initiating charge for dynamite , during the last decade it has been replaced to a large extent by less sensitive , more efficient, and cheaper combinations of ignition , priming , and base charges . Commercial detonators were once of relatively simple construction and almost universally identical . Today they are technically complex, with special nodifications for particular uses ; they have developed along different lines n various countries and even among the several manufacturers within any one country .

Apr 1, 1943

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

This publication contains four papers presented at a seminar on mine subsidence control held in Pittsburgh, PA, on September 19, 1985. The seminar was designed to keep the mineral industry informed of new technology developed by the Bureau of Mines that permits reliable and accurate prediction of mine subsidence. The papers describe actual field studies undertaken by the Bureau to monitor surface subsidence over longwall panels. Topics discussed include the efects of subsidence on water table levels, the development of subsidence pre calculation methodology suitable for use with the specific lithological conditions of the Pittsburgh coalbed, an engineering comparison of technologies used in surveying for longwall mine subsidence, and a comparison of the process of subsidence over two different longwall panels.

Jan 1, 1985

By Arthur Crowfoot

This paper describing t o concentrating practice of the Phelps Dodge Corporation, Morenci Branch, at Morenci, Ariz., is one of a series of articles on concentrating methods and posts being prepared by the Bureau of Mines. The Morenci concentrator, locally known as No. 6 concentrator, treats 5,000 dry tons of ore per 24-hour day by primary tabling followed by two stages of flotation treatment, at 48-mesh size and 65-mush size respectively.

Jan 1, 1931

By Pedro Lilienfeld

This Final Report describes a program whose objective was to design, develop, fabricate, and test an airborne mass monitor for unattended and recording measurements of the concentration of dust in mining environments. Sensing collection are performed by beta-radiation attenuation and inertial implementation respectively. The instrument is portable, battery or line operated provides a digital printout of the mass concentration during each selection sampling period, as well as the accumulated mass of dust, and the elapsed sampling time.

Jan 1, 1974

By Alton B. Cook

In the Scurry Reef field, Scurry County, Tex., a study was made to determine the physical properties of the oil in all parts of the reservoir by a new method developed for this study. The method involved correlation of data from a survey 1 of the gravity of the produced oil, from measurements of gas-oil ratios on key wells selected to give representative data for the entire reservoir, and from laboratory analyses of reservoir oil samples. A field survey was made of the API gravities of the produced oil by testing oil samples from 107 key wells. Precise gas-oil-ratio tests were made on 45 key wells that were producing under comparable separator-operating conditions. Subsurface-oil samples were obtained from seven wells, selected to provide reservoir oils ranging approximately from a minimum to a maximum in saturation pressure. The physical properties of the subsurface-oil samples were determined, and correlations were made of these laboratory data with the field gas-oil-ratio test data. These correlations were then used to estimate physical properties of the oil throughout the reservoir. A logical procedure of determining the variations in physical properties of reservoir oils in most fields is to obtain and analyze subsurface-oil samples from enough key wells to provide an ample coverage of the field. Under this procedure, data from a large number of samples would be needed to provide the desired information on the Scurry Reef field, as it is one of the largest known in the United States.

Jan 1, 1955

By Mildred Nadler, Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular indus- try or commodity. 2. Recirculation is dependent on the processing requirements of a par- ticular commodity, the manner in which the water is used, cooling and condens- ing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

May 1, 1965

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969