Search Documents

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By Michael Schmitz, John A. Organiscak

ABSTRACT: A method (patent pending) has been developed to determine the quality of environmental cab filtration systems. This method utilizes specially configured filter cartridges to remove carbon dioxide from the ambient air with the environmental cab’s air filtration system. A real-time gas monitor is placed inside an unoccupied cab with the filtration system running to time decay the carbon dioxide to its lowest concentration or equilibrium level. The outside carbon dioxide concentration level can be measured concurrently with another gas monitor or with the same inside cab gas monitor during a representative period before and after the inside sampling is conducted. Cab filtration system leakage is comparatively deduced from the difference between the special cartridge filter efficiency and overall cab efficiency. Laboratory trials have illustrated that desirable high efficiency test filter configurations (greater than 99 % efficiency) can be devised, but have air quantity and test time limitations. These trials also demonstrated that CO2 penetration was reflective of controlled air leaks around a high efficiency filter under equilibrium conditions. This report examines the elements of this patent pending method.

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By K. K. Kelley

The first bulletin (269) 3 in this series, which appeared in 1932, compiled the entropy values then available for the elements and in-organic compounds, results being listed for some 150 substances. Elaborations and revisions followed in 1936 (272) and 1941 (280), when over 500 usable entropy values were tabulated. The present bulletin constitutes a further elaboration and revision. The accumulation of data since 1940 has been marked, and 800 entropy values now are available. The present bulletin also contains all the pertinent explanatory matter that appeared in its predecessors. Thus, it retains the same dual purpose of assembling the available values of the entropies at 298.16° K. of the elements and inorganic compounds and giving enough explanation of methods of calculating entropies to make the results comprehensible.

Jan 1, 1950

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By Robert Vinson

This article examines the spatial variability of dust concentrations within a coal miner?s breathing zone and the impact of sampling location at the cap lamp, nose, and lapel. Tests were conducted in the National Institute for Safety and Health Pittsburgh Research Laboratory full-scale, continuous miner gallery using three prototype personal dust monitors (PDM). The dust masses detected by the PDMs were used to calculate the percentage difference of dust mass between the cap lamp and the nose and between the lapel and the nose. The calculated percentage differences of the masses ranged from plus 12% to minus 25%. Breathing zone tests were also conducted in four underground coal mines using the torso of a mannequin to simulate a miner. Coal mine dust was sampled with multi-cyclone sampling cans mounted directly in front of the mannequin near the cap lamp, nose, and lapel. These four coal mine tests found that the spatial variability of dust levels and imprecision of the current personal sampler is a greater influence than the sampler location within the breathing zone. However, a one-sample t-test of this data did find that the overall mean value of the cap lamp/nose ratio was not significantly different than 1 (p-value = 0.21). However, when applied to the overall mean value of the lapel/nose ratio there was a significant difference from 1 (p-value < .0001). This finding is important because the lapel has always been the sampling location for coal mine dust samples. But these results suggest that the cap location is slightly more indicative of what is breathed through the nose area.

Jan 1, 2007

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program&apos;s beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By V. F. Swanson

As part of the Bureau of Mines titanium resources examination program, samples of altered rock (saprolite) and unaltered rock from the Roseland anorthosite near Roseland, Nelson County, Va., were tested for amenability to beneficiation by flotation. A flotation technique was developed to produce bulk concentrates of ilmenite, rutile, sphene, and leucoxene. It was necessary to first float apatite using oleic acid as the collector, in an alkaline pulp with dextrine as a titanium mineral depressant. The titanium minerals could then be floated from the apatite tailing, using fluosilicic acid to depress the remaining apatite, morin to depress ferromagnesian minerals (when present), and oleic acid as the collector. A bulk titanium mineral concentrate, analyzing 66.0 percent Ti02 and 0.08 percent P205, was obtained from a sample of the unaltered rock which contained 5.45 percent TiO2 and 2.81 percent P205. Overall recovery in the concentrate was 47.1 percent of the total TiO2 in the ore. About 55 to 65 percent of the saprolite sample was clay and was removed by attrition scrubbing and decantation. The apatite prefloat procedure was applied to the saprolite sands; subsequent titanium mine: 1 flotation recovered 72.2 percent of the Ti02 in a bulk concentrate containing 65.1 percent TiO2 and 0.20 percent P205.

Jan 1, 1962

By William J. Campbell

Expansion measurements of platinum, added as an internal standard, are used for thermal calibration of X-ray cameras and diffractometers. Accuracy of the temperatures derived by this technique depends on the precision of expansion measurements and the reliability of reference expansion data. Temperature measurements to ± 1° C. require ?d or ?a to be determined within ± 0.001 percent. Selected expansion data are concluded to be reliable to 2° C., 5° C., and 25° C., over the temperature ranges 0° C. to 700° C., 700° C. to 1,000° C., and 1,000° C. to 1,700° C., respectively. Tabular expansion values from 25° C. to 1,700° C. in 2° C. intervals were calculated from the following equation; Expansion, percent = [8.91 + 1.28 x 10-3(t-25) + 0.04 x 10-6(t-25) ] [t-25.104 ] These tabular values facilitate future corrections of published temperatures as more reliable expansion-temperature data become available.

Jan 1, 1962

By S. J. Schatzel, W. P. Diamond, F. Garcia

Methane explosions have historically been one of the major causes of fatalities and injuries in underground coal mining operations. Advanced numerical models and predictive modeling approaches have the potential to offer optimized methane control solutions for general mine planning purposes and to address specific methane-related operational problems. This paper describes the development of reservoir models for the longwall mining environment and their application for investigating the influence of various completion design parameters on the methane drainage effectiveness of gob gas ventholes. The influence of increasing longwall panel width on the effectiveness of current gob gas venthole completion and placement strategies in the Pittsburgh Coalbed were evaluated and optimized designs developed to capture the expected increase in methane emissions on the larger panel.

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers&apos; dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area&apos;s northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

The Bureau of Mines in the Department of the Interior is increasingly concerned with the safety and health of personnel engaged in coal-mining operations, particularly below ground. The Bureau is also concerned with improving the utilization of domestic mineral resources, and reducing the environmental impact of mineral operations. One obvious way to improve safety and minimize health hazards would be to eliminate coal mining entirely by bringing the energy value of the coal to the surface in some other way, such as by partially burning it underground to form combustible gases and bringing these gases to the surface, where their energy content can be put to use. This technique might also improve the utilization of the coal resource. ? Accordingly, the Bureau of Mines, interested in re-evaluating underground coal gasification technology in terms of current and expected conditions in the United States, requested Arthur D. Little, Inc., (ADL) to appraise the technology to determine: ? Whether the current (1971) state of the technology offers a technically feasible method for gasifying coal underground that is applicable to the reserves of bituminous and lower rank coals in the United States. ? Whether a program of research and further development of the technology could ultimately make it a technically feasible alternative to current open-pit and underground coal mining operations. ? What the nature and cost of further research and development work in the technology should be.

Jan 1, 1971

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Keith S. Olson

During 1982 and 1983, the Bureau of Mines concentrated its fugitive dust control research on haulage road dust suppression by newer chemi-cals relatively unknown in the mineral industry, innovative dust control designs for haulage trucks, chemical tailing basin stabilization, and combined chemical and vegetation tailing basin stabilization. Relatively unknown dust suppression chemicals and innovative aerodynamic modifications to haulage truck fender designs were tested on a Minnesota sand and gravel operation haulage road. Magnesium chloride salt at 95-pct control efficiency and a petroleum derivative at 70-pct control efficiency were effective in suppressing dust generated by haulage vehicles; however, none of the fender modifications were successful. Commonly used dust suppressant chemicals were tested on a Minnesota taconite tailing basin to reduce the dust lift-off during the spring and fall dry seasons. The most successful chemical was lignin sulfonate with a seasonal cost of less than $200 per acre to achieve 90-pct dust control. When chemical treatments for immediate dust control were com-bined with revegetation for permanent control, the most promising chemical treatment based on vegetation response was lime-neutralized lignin sulfonate.

Jan 1, 1987

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975

By J. Torma-Krajewski, C. Hipes

Although many mining companies apply ergonomic principles, it is usually done either informally and/or reactively. An example of an informal approach is replacing worn equipment (such as seats) with models that have ergonomic features. Another example is modifying a task to eliminate safety hazards. Such approaches reduce risk-factor exposures that can lead to musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/ equipment after an MSD occurs. However, neither of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper discusses how Vulcan Materials Company applied ergonomic principles and implemented interventions to reduce risk-factor exposures.

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939