Search Documents

By M. Feely, W. G. O'Keefe, C. O'Reilly, M. P. Holdstock

A petrographic and microthermometric study of fluid inclusions in the Kentstown Granite, crosscutting quartz (VI) and calcite+quartz (V 2) veins in the granite and calcite+quartz (V 2) veins in the overlying sediments was performed on samples taken from the borehole. Comparisons of the type 1, type 2 and type 3 fluid inclusion populations recorded in the present study with those from other Irish Caledonian granites strongly suggest a similar fluid evolutionary history. Furthermore, the low-temperature CaC12-rich brines (type 5) of this study, which must be syn- to post-Lower Carboniferous in age, have correlatives both in Irish Caledonian granites and in the Lower Carboniferous base-metal deposits of the Irish midlands

Jun 19, 1905

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By S. A. Sayed, M. N. M. Ahmed, M. A. Doheim

The performance of a 12.7 cm hydrocyclone was investigated by considering the effect of design variables (diameters of the vortex finder and apex) and operating variables (pressure drop and solids content of the feed) at a medium feed solids concentration of mixed minerals. Cut-size was found to be the most important parameter in hydrocyclone design and operation. The effect of feed pressure in reducing hydrocyclone cut-size is less pronounced at medium feed solids concentration with a mixed mineral feed. The choice of vortex finder diameter and apex diameter becomes more sensitive at medium feed solids concentrations. The effect of feed solids concentration in increasing the cut-size becomes less marked at higher concentrations. Predictions of an empirical model were found to be in good agreement with experimental data. Comparison of results obtained from the model with those predicted by theoretically derived models showed the latter to be more promising, with the turbulent two-phase model giving closer agreement with the experimental data

Apr 1, 1995

By R. K. Dunham, D. J. Reddish, X. L. Yao

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 10 refs. The integrated approach combines a powerful ground movement prediction program with a knowledge-based expert system. ESDAS (Expert Structural Damage Assessment System) was developed to evaluate mining subsidence damage in the form of risk and in terms of the three vital contributing components (mining factors, site factors and structural factors). Using a certainty factor risk assessment technique, the system can be used to predict the likely damage to a particular structure subjected to mining subsidence. A previously developed powerful ground movement prediction program, SWIFT (Subsidence With Influence Function Techniques), has been combined with the expert system to allow the mining factor to be more accurately determined in a broader range of mining layout. Since SWIFT can be calibrated to any particular coal field using local subsidence data, it is believed that the integrated system could be used in any coal field worldwide for the assessment and control of mining subsidence damage risks

Dec 1, 1995

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By A. H. G. Mitchell

Most, if not all, of the six recognised post-Cretaceous, predominantly andesitic mineralised belts in the region are now thought to be subduction-related magmatic arcs. The Inner Carpathian arc and the Eastern Bosnia or Drina-Rhodope arc host numerous vein and replacement deposits with epithermal features and Zn-Pb+/-Ag as the predominant economic minerals. In contrast, the south Apuseni Mountains have produced over 1 600 t Au from epithermal veins but very little Zn-Pb. Recent age determinations and geophysical data from the Baia Mare district of the Inner Carpathians suggest that mineralisation succeeded volcanism by 1-2 m.y. and accompanied crustal extension and the cooling of a large, mushroom-shaped pluton whose boundaries define the mineral district. In the south Apuseni district, mineralisation can be explained by mixing of meteoric with low-salinity metamorphic water expelled during intrusion of mafic rocks into the middle or lower crust. The more continental or cratonic crust in the Drina-Rhodope and Inner Carpathian arcs precluded the input of low-salinity, Au-bearing metamorphic water; the Zn-Pb deposits formed where convecting meteoric water mixed with saline water, possibly introduced through carbonate rocks in the basement

Aug 1, 1996

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995

By M. K. Abd El-Rahman

A complete chemical analysis of the waste showed that it contains 15.64% P2O5; X-ray diffraction analysis revealed that it is composed mainly of francolite, calcite, pyrite, quartz and dolomite. The phosphate values were recovered and the settling rate of the wastes enhanced by the use of hydrocyclone and flocculation techniques. The hydrocyclone produced an underflow enriched in phosphate and an overflow enriched in clays. The former represented 39.8% by weight of the phosphatic clay waste and assayed 26% P2O5 at a recovery of 66.36%. The results of flocculation of the phosphatic clay waste showed that both the degree and rate of settling were increased and that the process water could be recycled. The settling rate was 37 times greater when anionic polyacrylamide A130 was used

Jun 21, 1905

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By M. Moinpour, Y. K. Rao

The catalysed direct reduction of copper sulphide with carbon and lime was investigated in the range 850-1000 degrees C using Cu2S-CaO-C and Cu2S-4CaO-4C reaction mixtures. The effects of the catalytic additives K2CO3, Li2CO3, Na2CO3, NaF, Na2SO3 and the ternary eutectic (K,Li,Na)2CO3 were determined. Potassium carbonate, sodium fluoride and the ternary appear to be the most effective catalysts for the direct reduction process. The rate enhancement of the catalysed carbothermic reduction of copper sulphide in the presence of lime was explained in terms of the catalysis of the Boudouard reaction

Jul 1, 1991

By J Parnell, B Manson

Bitumen occurs in the basins in reservoir sandstones, in veinlets close to hydrocarbon source rocks, in veins through lava beds and in sulphide-mineralised veins where it is closely associated with, but predates, the sulphides. The role of organic matter was probably in enhancing metal reduction by creating a low-Eh environment rather than in metal transport. Coeval euhedral quartz crystals or albite in sulphide-bearing carbonate veins provide evidence of an aqueous component to the hydrocarbon fluid

Aug 1, 1995

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By V. Krupa, E. Lazarova

A method is proposed for the continuous calulation of a rock mass in real time while tunnelling with a TBM. Rock properties are investigated through models of the fracture stress under the disc cutters, the quasi-shear stress between the disc cutters and the specific energy of cutting under the disc cutters. Comparison of theoretical and monitored data of cutting specific energy can be used to determine theoretically the prevailing shape and size of the bulk debris. The shape and size of the chips from a given rock vary with the boring parameters. Introducing shape and volume corrections into the models of the evaluated stresses suppresses the influence of the boring regime and allows the rock properties to become dominant

Dec 1, 1996

By R. A. Ixer, R. A. Lord, H. M. Prichard, A. J. Boyce, P. McConville, C. T. Pillinger, I. P. Wright, J. Maynard

Analysis of 62 samples show that the sulphides throughout the igneous stratigraphy have a magmatic signature, with the exception of the uppermost gabbros and the lowermost basal thrust talc-carbonate lithologies. Mean delta-34S values for whole-rock samples from harzburgites, dunite pods in harzburgite, crustal dunites and wehrlites, the main and high-level pyroxenites and gabbros suggest that the primary sulphides derived their sulphur from a magmatic source enriched in 34S. This finding is compatible with the proposed origin of the ophiolite above a subduction zone. Values for pyrite mineralisation in the uppermost part of the gabbros are thought to result from precipitation from a seawater-derived fluid, while isotopically light sulphur in the basal thrust could have been introduced from underlying metasediments. The replacement of pentlandite by heazlewoodite has not led to sulphur fractionation

Jun 19, 1905