Search Documents

By B. Francis

Literature provides only limited information regarding the behaviour of laterally loaded piles socketed into weak rock masses. A laboratory program, comprising a number of tests of scaled models of the pile/rock mass system has been conducted. A synthetic rock, known as Johnstone was used to simulate a naturally weathered and fractured siltstone. The load-deflection behaviour of the test piles was measured, and strain gauges were fixed to the model piles to assess the bending moments. The laboratory results are compared with the results from several theoretical models, some of which are in the form of commercial software packages. This study highlights the inadequacy of existing methods to adequately model the influence of rock joint orientation in geotechnical design. Additionally, numerical modelling of the pile/rock mass system was carried out using the discrete element program UDEC. The importance in modelling the system using discontinuum mechanics is highlighted, particularly to capture the anisotropy of the rock mass.

Jan 1, 2004

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010

By Frank Borda

Two recent projects were completed in Ontario, Canada for major hospital additions that involved excavation support of heritage masonry structures. Conventional continuous caisson wall schemes were replaced, with significant cost savings, by tied back shotcrete systems. Using a combination of conventional design and FLAC analysis, excavation support was designed to permit excavation in competent to weak soils that limited horizontal movements of the existing structures to between 3 and 8 mm. The use of vertical wall elements (micropiles) integral to the shotcrete wall to support both the vertical wall loads and the face of the excavation was deemed to significantly reduce lateral and vertical wall movements. FLAC analysis was used successfully to predict wall movements and optimize design. The shotcrete method proved to be flexible and adaptable to design changes during the project. This permitted convenient accommodation of changes to the building geometry after excavation support had commenced. In addition the method accommodated staged demolition and excavation support of portions of the existing structure at low cost, conveniently and without delays.

Jan 1, 2004

By D. E. Sherwood

Twelve toe grouted, and eleven ungrouted piles, founded in very dense sands have been analysed to establish how toe grouting enhances pile performance. It is shown that pile stiffness is greatly increased, and that pile bases work effectively. This is in contrast to ungrouted piles, where some milli­meters of base movement may be required before the base is mobilised. Grouting appears to recover most of the disturbance caused during construc­tion, but in general does not enhance the ultimate bearing capacity of undisturbed ground.

Jan 1, 1989

By Issa S. Oweis

Two Towers are currently under construction in Central Moscow in the Russian Federation. Building A is a 96 story tower and Building B is a 65 story tower. The columns in both structures bear on a thick concrete mat that is supported on drilled shafts, 1.5 m in diameter. The shafts derive their capacity from weak limestone with layers of marl. Assigned allowable shaft loads were initially based on rock strengths that were later verified by load tests using the Osterberg Cell. One of the load tests was carried to near failure which allowed refining socket friction values that were later used in the design of Building A. All shafts were advanced using an auger and concrete placed in the dry. Grout tubes were placed with the reinforcing cage which allowed grouting of the limestone in contact with the shaft. Load sharing between the shafts and the mat was approximated using published methods as well as site specific finite element analysis. This paper covers the methodology of design, analysis of the Osterberg results to derive non-linear stiffness of the rock and differences between finite element analyses and results by approximate methods.

Jan 1, 2007

By Anne Fagot

Because of the risk of corrosion caused by stray currents, steel foundations and steel sheet piling are generally prohibited in the vicinity of railway structures. Steel solutions are only accepted if they are shown to meet the required design working life and if this can be achieved at an acceptable cost compared to competing materials. The influence of stray currents on various steel sheet piling designs was studied using software initially dedicated to gas and pipeline industries and cathodic protection systems. It has been successfully adapted to model stray currents affecting steel sheet piling. Corrosion rates assessed using this modeling software were considerably lower than commonly expected. Zones of potential corrosion risk were identified; specific cost-effective countermeasures could be established. The developed software tool can help to optimize the design of piling solutions in the vicinity of DC railway power systems in terms of suitable countermeasures that meet structural reliability and cost requirements.

Jan 1, 2008

By Anne Lemnitzer

When a major storm system stalled over Western Europe last summer, it pro- duced the deadliest flood on European territory in the last two decades. Beyond record-setting rainfall over countries such as Luxembourg, Switzerland, France and the Netherlands from the storm's "Bernd" low pressure system, more than 230 people were killed in Germany and Belgium. The storm system also caused over an estimated $20 billion (€17.7 billion) of damage. A team from the Geotechnical Extreme Events Reconnaissance (GEER) Association, supported by the National Science Foundation, was mobilized to investigate the potential impacts of the widespread flooding in Germany, Belgium and the Netherlands. Members of the DFI Europe regional chapter closely collaborated with the U.S.-based GEER team and many other engineers and scientists in Europe to collect perishable data and study flooding effects and the event's resulting impacts on geostructures, such as bridges, retaining walls, dikes and embankments. This article features some of the vast information collected by the team, which has recently been published in a comprehensive reconnaissance report and made available for free at geerassociation.org. All data will also be accessible at the NEHRI DesignSafe Cl data repository.

Feb 1, 2022

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1998

By G. G. Meyerhof

The paper reviews the state of the art of estimating the bearing capacity and settlement of pile foundations in sand and clay soils, including the effects of pile installation, scale effects of pile size and embedment and non-uniform soil conditions. The lateral resistance of pile foundations and effects of eccentricity and inclination of the load on the bearing capacity and movements of pile foundations in sand and clay are considered on the basis of some recent investigations.

Jan 1, 2010

By Shawn Downey

A helical pile with in-situ grouted shaft was used to underpin the existing slab of a large retail store in the Edmonton, Alberta Canada area. The existing structural slab did not have the capacity to support the increased load requirements. The design to upgrade the capacity specified a drilled shaft as the deep foundation to underpin a portion of the slab. A helical pile was quoted as an alternate and ultimately won the bid based on the advantages of the system. After an ASTM D1143 Quick Load Test confirmed the axial compression capacity, 723 helical piles with grouted shafts were installed in 3 weeks underpinning 40% of the 93,000 ft2 (8,660 m2) building.

Jan 1, 2003

By H. R. Taber

The extensive subject area "Engineering Practice of Ground Improvement" will be treated within the limitations of space and the writer on the basis of personal practice and experience?largely in Northern California over a period of some thirty-six years and, in "ground improvement" work, with an emphasis on transportation facilities. The stress is on improvement of ground conditions, rather than on techniques of improving inherent earth materials characteristics. "Ground improvement" is discussed as engineering resolution of existing or emergent earth materials defects or deficiencies?that is, as the technically feasible procedures best adapted to achieving a required level of service within physical, economic, social and other constraints. A "required level of service" concept is presented as a tool in evaluation of appropriate ground improvement work.

Jan 1, 2010

By Makarand G. Khare

Though the phenomenon of dragload is known for many decades, there is a lack of clear guidelines to evaluate the amount of dragload. The development of dragload depends on relative movement between pile and surrounding soil which is a complex phenomenon and requires a detailed numerical analysis. Bitumen layer has been used in the past with varying degree of success in reducing the dragload but the reduction appears to depend on number of parameters. No procedure is available in literature to estimate the dragload when a slip layer is applied on pile surface. This paper investigates performance of two commercially available bituminous coats to reduce the negative skin friction on pile. Direct shear test apparatus was used to model the interface friction between soil and coated pile surface. The lower half of direct shear box was replaced with either a concrete block or a mild steel block representing pile surface. Two types of bituminous coats namely Shalikote and bitumen having penetration value of 30-40 were evaluated in this study. Shearing resistance of pile material-coat-soil is found to be influenced by normal stress, coat thickness, and rate of shear. Laboratory results are compared with published field data where coated and uncoated piles have been load tested.

Jan 1, 2006

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Kashyap Chaturvedula, Emad Farouz

The paper presents a discussion on the axial capacity of deep foundation elements bearing in the Yorktown formation in the southeastern region of Virginia. The fossiliferous marine soils of Tertiary age Yorktown formation typically consist of silty/clayey Sand or sandy Silt/Clay with varying amounts of shell fragments. The Yorktown formation is generally divided into Upper and Lower Yorktown layers depending on the shell content and the percent fines. Results of multiple load tests performed by Jacobs Engineering on auger cast piles as part of water and wastewater treatment plant expansion projects in southeastern region of Virginia are presented in this paper. The paper describes the subsurface investigation methods used to study the existing subsurface conditions and the design methodologies followed to estimate the axial capacity of the auger cast piles. The paper provides details regarding installation of test piles, instrumentation, load testing procedure, and interpretation of test results. The paper presents a comparison between the various methods of estimating axial capacity of auger cast piles based on the SPT-N values, the empirical methods for the Yorktown formation and the load test information. The paper distinguishes the side resistance values obtained within the upper and lower Yorktown formations. The paper compares the various design methods to the multiple load test results and recommends a design modification that is closer to the load test results.

By Michael E. Ameel

The vibrated beam method of installing a vertical barrier wall is one of the least applied techniques, yet given certain site conditions and constraints, it is a cost-effective and proven method of controlling lateral groundwater flows. A recent full-scale application of this technique demonstrated its usefulness at an active manufacturing facility located in Northern Wisconsin. At this site, a 3,233 foot long cutoff wall was keyed into an underlying bedrock, which was located an average of 40 feet below the ground surface. Using a slag cement-clay based slurry, a 1E-7 cm/sec or less, nominal 4-inch wide cut-off wall was constructed using the vibrated beam method. Challenges included working around an active manufacturing facility with minimal access to the work area; installing the wall through a very dense glacial till; minimizing soil excavation volumes of potentially impacted soil; and, working around and adjacent to numerous active utility lines without impacting the facility operations. At utility locations, the vibrated beam wall was supplemented with a jet grout panel wall, without the need to bypass or otherwise interrupt any of the plant?s utilities. Quality control consisted of the monitoring and measuring of slurry parameters, survey control, and real-time monitoring and documentation of all critical barrier wall installation parameters. A vibration monitoring plan was also implemented to measure vibrations at utilities and adjacent facility structures. Proper equipment selection, significant up-front planning and close coordination with the facility resulted in a safe and successful project. The work was completed ahead of schedule during the 2009 construction season.

Jan 1, 2010

By Masaki Kitazume

Five papers were presented orally to the topics of Jet Grouting and Deep Mixing. The session was started with a brief introduction by the moderators. Following the oral presentation, floor discussions were directed by the moderators. A brief introduction of each of the oral presentations is provided before each discussion.

Feb 10, 2003

By Xuhui

Pile foundations are underground projects which are carried out under complicated site conditions, so it is difficult to summarize their characteristic patterns from the everchanging practical pile foundations. In combination with theories, the paper analyses the effects of sound reinforced concrete piles and various types of defective piles on the propagations of stress waves. Through testing on prototype pile models, by use of the transient dynamic method and comprehensive analysis in both time domain and frequency domain, their reflection characteristics and patterns are acquired. In addition, discussions are carried out in combination with some real projects. Our model tests include comparison of large scale pile models of 20X20cm in cross section, 5. 0m in length respectively in air, standard sand, and natural stratum; prototype model tests of digged piles of 0. 7-1. 2m in diameter, and 18m, 30m in length; prototype model tests of bored piles of 0. 6m, 0. 8m in diameter, 12-20m in length. Test results show that no matter in air or buried in medium, the intrinsic characteristics of sound piles and various types of defective piles are fixed. In their time domain waveforms and spectral diagrams, obvious regularity are shown, which proves that the relations between the pile natures and their dynamic responses are fixed, which provide basis for correct judgement of pile soundness and natures of defective piles.

Jan 1, 1991

By Kyle M. Rollins

To improve our understanding of lateral resistance of pile groups, a series of lateral load tests were performed on a full-scale pile group using both static and dynamic loads. The pile group consisted of nine 0.6 m-diameter steel pipe piles driven into clay. During the static tests, the load was cycled fifteen times to evaluate the drop in lateral resistance that would occur due to repeated loading and the formation of a gap. The peak load typically decreased by about 15% from the initial cycle to the last cycle. The load carried by each pile was also measured and there was a significant drop in resistance for the piles in the trailing row relative to the leading row. The dynamic force was applied using the Statnamic loading system which produced a lateral force of 3500 kN (787 kips) in about 0.1 seconds. In two cases, dynamic loads were applied following application of 15 static load cycles. In these cases, the dynamic lateral resistance was about the same as the static resistance, likely due to gaps around the pile. In three other cases, the dynamic force was applied prior to the cyclic loading. In these cases, the dynamic resistance was 30 to 60% higher than the static resistance. Simplified analyses suggest that the difference in resistance could be attributed to damping produced by the soil surrounding the piles during the virgin loading.

Jan 1, 2002

By Mitsuhiro Shibazaki

Generally, water-soluble polymers are effective in convergence of water jet ejected from a nozzle as they add viscosity to water. However, excessive additional polymers (added to keep water viscous) could increase friction on the contrary. Therefore, we have totally modified the jetting system from every possible aspect, such as the shape and upstream conditions of a nozzle in order to keep the flow spread to the minimum as stated in my presentation.

Feb 10, 2003