Search Documents

By D. Kim

Kennecott operates one of the largest and most modern copper refineries in the world at Magna, Utah, USA. The inputs to the refinery are anodes produced at Kennecott Smelter, which has extremely high contents of lead and bismuth. In order to minimize undesired effects in the electrolytic refining process, unwanted impurities, especially bismuth, must be controlled. This paper describes the process development of practicing state-of-the-art quality control and presents the pilot test results of using the MRT Technology for Bi production.

Jan 1, 2007

By T. H. Etsell, P. C. Holloway

Vanadium is concentrated in the fly ash which is produced as a solid waste from oil sands operations in northern Alberta. Although a process flowsheet using sodium chloride as a roasting reagent has been developed at the University of Alberta, recent studies examine the p otential o f p otassium o r c alcium s alts a s alternative reagents for roasting Suncor fly ash to recover vanadium. Suncor fly ash was roasted with CaO, Ca(OH)2, CaCO3, CaSO4.2H2O and KC1 at 750, 850 and 950°C. Water leach extractions for the calcium compounds were low (<45%); leaching with 100 g/L Na2CO3 gave maximum extractions of 56 to 69% at 950°C. Ash roasted with KCI behaved similarly to ash roasted with NaCl. These tests indicate that similar roasting conditions (25 to 30% KCI, 850°C, and 2 to 4h) could be used to achieve similar water leach extractions (75 to 85%). However, the lower solubility of KVO3 in solution, compared to NaVO3, would make the use of KCI instead of NaCl less attractive from a process and economic standpoint. Mineralogically, leucite (KAlSi3O8) was the predominant phase in ash roasted with KCl while, in crystalline samples of ash roasted with calcium compounds, anorthite (CaAl2Si2O8) and pseudobrookite (Fe2TiO5) were identified. Ash roasted below 950°C with the calcium compounds remained poorly crystalline.

Jan 1, 2004

By Brent Robertson

Failure to meet quality objectives during the execution of any industrial project has lasting negative impacts on facility life cycle performance. Cost overruns, schedule delays, and rework are characteristics of project quality issues that arise during the project. Commissioning and start-up problems, low production, production bottlenecks, breakdowns and the necessity for operational work-arounds are characteristics of project quality issues that appear after project completion. Risks such as production facility downtime, shortened equipment life, and potential HSE violations must be clearly identified and addressed during project planning phases. Appropriate Quality Assurance (QA) and Quality Control (QC) focus must be placed on identified high-risk areas. In order to be effective, quality systems must be flexible, non-confrontational, consistent, and adaptable to projects of any size ? from capital mega-projects to small maintenance projects. All project participants must be aligned in how they are approaching quality and the difference between QA and QC must be clear to everyone on the project. Emphasis must be placed on QA activities to minimize project cost, reduce rework, manage change, and reduce the production facility operational risk. QA is focused on the work processes used to generate the design and confirming that the processes are present and being followed. Issues in the work processes guarantee that the output drawings and specifications will be less than optimal. The identification and monitoring of quality-critical processes provides a focus for QA activities. QC activities are then used to generate proof that the project was implemented correctly and become a key part of the turnover.

Nov 1, 2011

By Alireza Entesari

Removal of metal ions from effluents represents a significant technical challenge. As a consequence several industries, including mining, are faced with issues relating to removal of contaminant cations and anions from solution. This study evaluates three natural mineral materials referred to as basalt, scoria, and calcined shale for treatment of metal contaminated effluents by adsorption. Adsorption tests were conducted to asses the possibility of removing cationic and anionic metal ions from prepared solutions and mine water effluents. Sustainable production of industrial minerals requires that a diverse range of added value products be introduced.

May 1, 2006

By X. Zhong

Thermal shock resistant properties of reaction sintered bauxite-based ß -Sialon bonded corundum have been investigated, and the results are compared with those of Al2O3 based counterpart. It is found they all have very good thermal shock resistance. Their residual strength ratios after one thermal shock cycle at ? T=1200°C and A T=1350°C are 61-73% and 53-65% respectively. TSR parameters are calculated based on thermal expansion, modulus of elasticity, and fracture toughness determined. The reasons for improved TSR of these composite materials are discussed.

Jan 1, 2004

By I. Cifuentes

Chemical and physical characterization of copper electrodeposits obtained on mesh and plate cathodes in conventional and reactive electrodialysis lab-scale cells have been carried out. The effect of Fe, Mn, Cl and guar on electrodeposit composition and morphology were determined by means of metallographies, scanning electron microscopy (SEM), atomic force microscopy (AFM), inductively coupled plasma mass spectrometry (ICP-MS) and Auger electron spectroscopy (AES). Each impurity influenced the deposit morphology in a different way (e. g. grain size, surface roughness). AFM proved to be a very effective tool for quantifiying and classifiying surface quality.

Jan 1, 2007

By Michael Schindler

Uranyl mineral dissolution appears to be complex, affected by factors such as solution pH and the presence of various cations in solution, and sometimes involving formation of secondary surface precipitates. Such secondary precipitates potentially could armor the underlying uranyl mineral surfaces from further dissolution. A detailed understanding on the formation of secondary precipitate is therefore essential for predictive modeling of radionuclide fate and transport in the subsurface. Several types of secondary precipitates on the surface of uranyl minerals were examined using Atomic Force Microscopy, Scanning Electron Microscopy, and, Xray Photoelectron Spectroscopy.

Aug 1, 2010

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015

By R. H. Keyes Duval

"The one point left off the table was pumping costs, i.e. the cost of pumping to the cyclones.At East Malartic 5 x 5 S R L pumps that had been used to pump the classifier overflow were used to pump the rod and ball mill discharges to the cyclones. Maintenance costs on the pumps rose from $105 in 6 months to $1000 per month. The pumps had to be operated at 1150 rpm and impellers lasted only 5 to 6 days. These pumps were replaced by 6 x 6 S R. L. pumps operating at 825 rpm, but at this speed the coarser sands settled and plugged the pipe lines and the speed was increased to 925 rpm. The maintenance cost is now $100 per m::rnth which is 0 003 cents per ton milled. The impellers now last 1 month and the casing linings 6 months.Density meters are often used on cyclone overflows and sometimes on the cyclone feed. Haliburton weighted tube density meters are used in some plants. They are cheaper than the radioactive density controller, $2500 as compared to $ 6000The angle of the discharge spray from the apex can be used to judge the quality of perform1nce of a cyclone.For ordinary metallurgical applications the inside slope of the cyclone is not too important but for fine separation steeper slopes are used.The cyclone is a versatile tool and will handle considerable variations in feed tonnage - probably up to 15%. Above this variation the number of cyclones used has to be increased or decreased or the tonnage fed to them has to be adjusted"

Jan 1, 1965

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

By Z. Sun

The hydrogen embrittlement and stress-corrosion cracking (SCC) behavior of an a -titanium alloy and its two kinds of welding samples have been investigated. The results show that this alloy has very low susceptibility to SCC, and the values of Kiscc for the alloy are 46.4 MPa ? m&apos; 65.86 MPa ? mu2 in the direction of T-L and L-T, respectively. The scanning electron fractographs show transgranular and quasi-cleavage fracture. The hydrogen embrittlement results show that the notch sample of the alloy is not sensitive to hydrogen, but the electro-beam welding and diving-arc welding samples are sensitive.

Jan 1, 2005

Recently, renewed interest in the recovery of uranium from leach solutions has necessitated a re-examination of the hydrometallurgy methods used for uranium in the 1960?s to 1970?s. A synthesizing overview of the lessons learned in those decades together with examination of recent developments in this area is warranted. This paper considers uranium recovery chemistry from acid and alkali leach solutions using solvent extraction and resin ion exchange, and provides information on circuit selection and configuration, equipment selection and design, as well as operational considerations. The unique thermodynamics of uranium solvent extraction are also presented and discussed.

Aug 1, 2010

By J. Koike

Mg alloys for structural application have attracted much attention. However, high process cost and poor mechanical reliability are major concerns upon expanding the application to a wider area. In order to break through these barriers, better ductility is desired at lower temperature. Plastic anisotropy and peculiar twin formation appear to play key roles in the deformation and fracture mechanisms of Mg alloys. In the paper, dislocation slip and twin formation are reviewed. The effects of crystallographic texture and grain size are discussed. The results suggest that a good control of microstructure and texture can improve ductility and mechanical reliability of Mg alloys.

Jan 1, 2006

By D. J. Sapsford

This paper details results from laboratory simulation of an innovative underground bioleaching process. The underground reactors are periodic flushed with recycled leachate to remove uranium that accumulates within the reactor water. This leaching cycle has been recreated within the laboratory. This study examines the influence of varying cycle protocol on uranium leaching. Protocol variants examined include variation of flushing frequency, flush volume, leachate recycle, nutrient solution (NPK) addition to reactors and Fe(III) sulphate addition to reactors. The presented data highlight the dramatic improvements in uranium recovery that might be achievable by varying the operating protocol for the actual underground reactors.

Aug 1, 2010

By I. Zhitomirsky, X. Pang

The outstanding thermal and chemical stability, excellent mechanical properties and biocompatibility of zirconia have made this material an important candidate for fabrication of advanced protective coatings on metals, graphite, carbon fibers and biomedical implants. Nanostructured polymer-ceramic composite films containing zirconia were synthesized on metallic substrates by combining cathodic electrosynthesis of inorganic particles with electrophoretic deposition of cationic polyelectrolytes. Thick crack-free oxide and composite coatings were obtained using this newly developed technique. The deposits were studied by thermogravimetric analysis, X-ray diffraction analysis, scanning electron microscopy and atomic force microscopy. The mechanisms of deposition are discussed.

Jan 1, 2004

By A. M. Hadian

The use of dolomite refractories in steel making and cement industries has advantages over other basic products particularly in countries where this type of refractories is produced. Due to existence of high-quality dolomite deposits in many regions of Iran, there is a good potential for producing dolomite refractories in the country. This study focuses on the effect of such additives as iron oxide and alumina on hydration resistance and density of Iranian dolomite. It was found that addition of Fe2O3 is more effective than Al2O3 on increasing density as well as resistance to hydration of dolomite.

Jan 1, 2004

By A. Fortin, C. Fréchette, M. Kreuh

Éléonore project is a gold ore processing plant at a mine site located near James Bay, Quebec, Canada. SNC-Lavalin was mandated by Goldcorp to perform EPCM services on the ore processing plant and permanent infrastructures of the project following an internal pre-feasibility study. The project incurred considerable challenges due to fast-tracking from a pre-feasibility to detailed engineering and construction. The paper reviews how the EPCM was carried out. Some of the challenges resulting from skipping the feasibility study stage are discussed. The paper also presents how multiple offices across Canada were used for the engineering design.

Jan 1, 2015

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words &apos;Maintenance&apos; and &apos;Equipment&apos; as follows: Maintenance shall mean the &apos;care of or &apos;the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank&apos;s peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank&apos;s peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank&apos;s Peak zone as Zone No. 2.

Jan 1, 1936

By D. L. Johnston

"Function and ApplicationsWater-only cyclones, (WOC) are a dynamic mineral separator which cause minerals to separate in a water medium by virtue of difference in specific gravity. Figure 1 shows diagramatic plan and sectional views of a water-only cyclone.A slurry of mineral matter and water is fed through the inlet opening under gravitational or pump pressure. The combined effect of centrifugal action and conical shape is to concentrate the heaviest fraction of mineral on the periphery and bottom of the cyclone. This layer of higher specific gravity particles increases in thickness and density between the cyclone inlet and apex. The action in the bed of higher gravity particles formed in the flattened portion of the cone surrounding the tip of the vortex finder deter;nines the specific gravity of separation or cut-point. Mineral particles of lower specific gravity flow with the bulk of the water, out the vortex finder. Mineral particles of higher specific gravity flow with little water out the apex. A more technically e:mct description of the functioning of the water-only cyclone can be found in previous publications noted in the references.The water-only cyclone was invented and refined by J. Vis man, formerly of the Canadian Mines Branch staff, between 1958 and 1965. The first industrial application noted in the literature was when it was introduced as a cleaner for fine coal in 1962. Since 1970 the water-only cyclone has become a common separation apparatus in many Canadian and foreign coal processing plants. The only other mineral industry application known to the author is in separation of gold bearing heavy minerals from sand<'>. The potential does exist for other applications and this area deserves to be investigated more thoroughly than it has been."

Jan 1, 1989