Search Documents

By C. L. O?Brian

Note: The figures quoted and used herein have been collected and furnished by the Dominion Bureau of Statistics. Without the help and willing co-operation of the officials of the Burreau, this study would not have been possible. Introductory and General Coal has one unique quality that distinguishes it from other minerals, one that is too, often forgotten. This is the quality of ubiquity. No other single mineral supplies such a wide and varied range of human requirements nor, up to the present, is there any indication of a rival in this regard. There is, consequently, reason for individual study of each of the major portions of the overall market for coa1. The provision of heat for our homes is a necessity of life in our Northern climate and the largest single source of this heat is coal. It is intended to present here a factual survey of the use ?of coal in home heating throughout Canada and the effect of these requirements upon the production of coal and the development of this phase of the mineral industry. The coals used for house heating in Canada fall into two more or less distinct classes, the very low volatile fuels such as anthracite and including coke, and the bituminous coals, including the sub-bituminous and lignite types. The bituminous coals are, of course, consumed in very large quantity by industry and the railways and are the most important type both in tonnage and in respect to the area supplied. Canada consumes annually for all purposes some 4,400,000 tons of anthracite, 4,300,000 tons of coke exclusive of Petroleum coke, and some 40,000,000 tons of bituminous coals. This is a fair measure of the relative importance to the overall economy although it will be seen later that the concentration of the household use of anthracite and coke into one area does create a considerable problem.

Jan 1, 1951

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By Roy Sage

Overview ? History ? background to current programs ? Kyoto status ? Support for technology development ? Support for GHG reduction ? Sources of information History ? 1988 - Toronto Conference - The Changing Atmosphere ? Proposed target ? CO2 levels reduced to 20% of 1988 levels by the year 2005 ? 1992 - Canada signed Framework Convention on Climate Change at the UN Conference on Environment and Development in Rio de Janeiro in June 1992 ? Canada launched the National Action Plan on Climate Change ? Kyoto protocol adopted in principle in 1997

Nov 1, 2002

By G. L. Spence

Prevention of cuprous and cupric oxide formation on stored ETP copper rod is a major concern for copper rod and wire producers. During normal storage periods copper oxide layers can increase from less then 100 A to more then 1000 A exceeding ASTM specifications and discoloring the rod surface. Various types of corrosion inhibitors are tested and compared in effectiveness for prevention of copper oxide formation on stored copper rod. Aromatic triazole compounds are also compared to a non-azole containing compound.

Jan 1, 2007

By H. Ito, T. Takasu

A leaching process for recycling small car motor scraps dismantled from End- of - Life -Vehicles (ELV) was investigated using waste pickling acid in steel work. Steel parts of mortar scraps were leached by waste pickling acid and Cu wire was recovered as pure Cu in the process. Pickling acid solution after leaching could be recycled in an ordinary process for waste pickling acid solution. High grade FeSO4 agent could be produced using H2SO4 as a pickling solution.

Jan 1, 2004

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By George F. Bassett

"More will be expected from the mine or metallurgical plant electrical system in the late 70's and 80's in terms of energy conservation, reliability and fire prevention. Increased electrical loads 1•equired by larger arc furnaces, higher-horsepower motors for mine hoists and pollution control fans, and greater use of electrical heating will have to be supplied. Computers and sophisticated instruments will be used more extensively and have less tolerance for electrical fluctuations. More extensive control and monitoring systems will be required to increase production and minimize operating and maintenance costs. Changing energy costs will prompt design engineers to investigate in-plant generation, particularly where sites are remote from existing utilities lines or steam from turbines may be used in the process. Some utilities are requiring industries to increase their power factor to above 90% ; others are requiring stricter control of voltage flicker from arc furnaces and harmonics from rectifiers. There is a trend to AC with solid-state cont1•ols instead of DC for large cranes."

Jan 1, 1976

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By M. Eikerling

The full competition between mass transport and reaction in PEMFC unfolds in cathode catalyst layers (CCLs). Recently developed models provide vital insights into effects of thickness and composition on effectiveness of catalyst utilization and performance. However, the CCL's key function in liquid water removal is rather unexplored. Studies of water balance in PEMFCs focus mostly on other cell components. Notwithstanding this prioritization, a simple calculation shows that the CCL is the PEMFC's favourite medium for conversion of liquid water into vapor. Porous structure and wetting properties steer the interplay of evaporation, transport and reaction. A model will be presented, that links pore space morphology, composition, distributed properties (concentrations, pressures, reaction rates, potential) with global performance (critical phenomena). It reveals how problems of flooding in the fuel cell could be mitigated by properly adjusting catalyst layer structure and operation conditions and under which conditions all liquid water arriving in the CCL would leave it as water vapour through the CCL/GDL interface. Results for a simple variant of the model emphasize the role of the CCL as a watershed for the whole cell.

Jan 1, 2005

By C. Phan

This paper outlines opportunities provided for enhanced management and process control by ISA PROCESSTM technology. ISA PROCESSTM technology has the core advantage of offering the potential for vastly improved electrode handling systems. This fundamental characteristic has enabled ISA PROCESSTM technology to develop management and process control systems that are modular, minimalist in their complexity and tailored to a tankhouse operating environment. A review will be presented on the current status of management and process control in ISA PROCESSTM tankhouses covering the central issue of electrode handling as well as electrolyte circulation systems, voltage monitoring, cathode plate tracking, and product tracking. Particular reference will be made of the recent development by Xstrata Technology (XT) and their technology partners, VRT Systems, of an Radio Frequency Identification (RFID) based solution for tracking ISA PROCESSTM cathode plates. The system encompasses fixed readers which identify plates passing through the stripping machines and the use of sophisticated tracking and database software enabling the development of cathode asset management and operational strategies. The performance of individual plates and batches of plates can be tracked through a full service history.

Jan 1, 2007

By T. S. Grewal, S. C. Gupta, H. Natarajan, T. W. McQuade, N. Nejibulloev-Mamedov

Cigar Lake is one of the world’s largest high-grade uranium mines. The ore mined at Cigar Lake is milled at Orano Canada Inc’s (Orano) McClean Lake mill. The average Cigar Lake ore uranium grade since the start of mining activities in 2014 is 17.8% U (range 8– 28%). To achieve budgeted production of 18 M lbs U3O8/yr the required average feed tonnage to the mill is about 45 kt/yr. Arsenic, occurring as arsenides and sulpharsenides, is one of the major elements of concern associated with Cigar Lake ore. The leaching process is a sulphuric acid leach under oxidizing conditions at near atmospheric pressure. The presence of arsenic in the ore consumes oxidant in leaching as well as ferric sulphate in tailings preparation for arsenic sequestration. The average arsenic grade since the start of mining at Cigar Lake is 0.57% As. Further, the ore is hosted in a matrix of sandstone and clay, which results in poor settling in CCD. The average uranium grade for the balance of Cigar Lake Phase 1 ore is expected to drop to 12.5% U and the average arsenic grade is expected to increase to 1.6 % As, with an annual average peak of 2.5%. Therefore the tonnage throughput required to sustainably meet the production target will increase to 55 kt per year. Orano partnered with Hatch Ltd. (Hatch) to perform a gap analysis study to identify key circuits and equipment in the mill that would require debottlenecking. A METSIM mass balance model of the McClean Lake mill was generated and validated with actual mill operating data. Various feed scenarios were then studied, and the outcome was a traffic light table, which highlighted feed scenarios that exceeded installed capacity of major equipment and circuits. The results provided the basis for the PDC for the pre-feasibility study. This paper will outline the results of the gap analysis, the mass balance model, the feed scenarios and the study undertaken to prepare the McClean Lake mill for the change in ore quality from Cigar Lake.

Jan 1, 2020

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By J. Holder

"A key barrier to vertical mineshaft construction is the construction access required for workers. A suspended work stage is used to provide this access for the mechanical, electrical and structural applications and other tasks. Work stage design is complicated considering the numerous types of construction activities that are executed simultaneously, the confined environment in which the work stage operates, the significant corrosion attack that is present, the weight limitations imposed by the mechanical hoist systems, and the risks associated with worker safety. Also complicating the design, these structures and their construction environment can vary with time. Hence, they can be described as 4D structures. The author has discovered significant synergies and advantages with integrating engineering design with detailed three-dimensional (3D) fabrication design. The significant reduction of minor design errors needing field correction will be underscored. The tender process is also accelerated since the design output is fabrication shop drawings including a detailed quantity takeoff output which lists each component required and its specific quantity. The paper presented will document the numerous advantages to the project using this approach. INTRODUCTION A key barrier to vertical mineshaft construction lies in the access for the workers to execute the construction. Suspended work stages are used to provide this access for the mechanical, electrical and structural applications as well as other tasks. The design of such work stages is complicated considering the numerous types of construction functions that need to be executed simultaneously, the confined environment in which it operates , the significant corrosion attack that is present, the weight limitation imposed by the mechanical systems for suspension, and the risks associated with worker safety. Also complicating the design, these structures and their construction environments can vary with time. They can be described as 4D structures with the fourth dimension being time. This design is a time consuming process. The post tender award is meticulous and requires strong teamwork between the steel fabricator and the consulting engineer. This teamwork may or may not be present and is dependant on the experience and relationship the team members have working together as well as other factors."

Jan 1, 2019

By Lawrence Devon Smith, Keith Spence, William Roscoe

"In March 2003 the CIM Council adopted and approved the document “Standards and Guidelines for Valuation of Mineral Properties” as developed by the Special Committee of the Canadian Institute of Mining, Metallurgy and Petroleum on Valuation of Mineral Properties (CIMVal). The document is referred to as the CIMVal Standards and Guidelines. The document evolved from a specific recommendation by The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) that the CIM form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties. The CIMVal Standards and Guidelines are organized into two parts: •,Standards which are general rules in the Valuation of Mineral Properties. The use of the Standards is mandatory if the Valuation Report is stated to follow CIMVal (although not mandatory in the sense of having regulatory authority). Definitions are given at the beginning of the Standards. •,Guidelines which elaborate on the Standards and, while not mandatory, provide guidance and best practices which are highly recommended to be followed in the Valuation of Mineral Properties.CIMVal specifies requirements for the Qualified Valuator who has the responsibility for choosing the appropriate approaches and methods for the valuation of mineral properties. With regard to the specifics of the application and practice of valuation approaches and methods, CIMVal directs the Qualified Valuator to the large body of published papers, published valuations, presentations and court judgments to guide his or her choice. This is also the approach taken by VALMIN (Australia) and SAMVAL (South Africa). To facilitate the dissemination of industry practice, the CIMVal Committee organized a “Valuation Day” at the CIM Annual General Meeting in Toronto (Mining Millennium 2000), on March 8, 2000. Industry experts presented papers on valuation of Mineral Properties which were subsequently published in a proceedings volume and individually ad technical papers in the CIM Bulletin. The Management and Economics Society of CIM has continued to identify and publish papers on valuation in the CIM Bulletin and Magazine. The present document gathers in one place the CIMVal Standards and Guidelines, the papers from the 2000 Valuation Day, and a number of subsequent papers that illustrate industry practice for the valuation of mineral properties."

Jan 1, 2003

By J. N. De La Vergne, J. S. Redpath

"The authors make recommendations that they believe will improve the efficiency of a mining company's use of a mining contractor's services. The recommendations are in the form of specific ""DO"" or ""DO NOT"" instructions, giving explanations and covering the contracting process from the end of the feasibility study to the end of the job. IntroductionThis paper is an attempt by the authors to set out some of the things which they feel an owner should consider to achieve maximum effectiveness from mining contractors. It is based on our experience as contractors as well as our experience as consultants to owners. Should this paper create the impression that we feel all the responsibility lies with the owner, this is neither our intention nor our belief.Before the Tendering Process BeginsUse Defined EstimatesIn Feasibility Study DO NOT estimate your cost or schedule by telephoning contractors and asking them for ballpark figures. The only kind of estimate that is worth anything is the one that is clearly defined on paper and bears the signature of the author. This type of time or cost estimate takes time to prepare. In general, the estimate will be worth what you pay for it.Ensure Adequate FinancingDO NOT ask contractors to tender on a project unless the funds have been approved for it. Remember that, depending on the size of the job, it will cost the contractor from $5,000 to $50,000 to prepare his tender. When financing is not assured, a single contractor should be approached regarding a detailed estimate and he should be paid for it. Contractors should not be expected to finance speculative mining ventures."

Jan 1, 1980

By T. A. Postolski, A. J. Sinclair

"Abstract - Where block (selective mining unit) grade distributions can be determined, the effect of average random errors of block grade estimates on metal recovery can be evaluated quantitatively. That is, for a given estimation error and cutoff grade, it is possible to calculate the quantity of metal that is lost as a result of misclassifying ore blocks as waste, as well as the dilution that ensues from misclassifying waste blocks as ore. Example calculations using a computer program GAINLOSS and realistic block grade distribution parameters for both a porphyry-type deposit and an epithermal gold deposit illustrate some fundamental relations that are important in quality control of estimation and in reconciliations concerning a comparison of ore estimates with production.Where the cutoff grade is on the lower tail of the grade distribution, metal arising from dilution can be much less than metal lost through misclassifying ore as waste. Hence, average grade of milled material could possibly be higher than expected (estimated) and tonnes milled will be smaller than estimated.Where the cutoff grade is on the higher tail of the grade distribution, tonnes arising from dilution will be greater than tonnes lost by misclassifying ore as waste. Thus, tonnage mined will be greater than estimated and the average grade milled will be less than estimated.The software GAINLOSS permits rapid comparison of the tonnes and average grade for all blocks selected as ore for a variety of levels of block estimation errors. These comparisons can be incorporated in a financial analysis to evaluate whether or not it is worthwhile to improve a high, average block estimation error to some lower value."

Jan 1, 1998

By Miguel A. Cuba

Trends in the mean and/or variance are a longstanding challenge in mineral resource modeling. Geologic modeling and/or grade domaining are often employed to account for heterogeneities in mineral grades; however, this is only practical up to a certain point since the number of data available for reliable model construction can be severely reduced. In such cases, trends remain present in certain geologic/grade domains and directly impact the modeling methodology; the trend must either be handled explicitly or a suitable approach is adopted to implicitly account for it. This is highly dependent on understanding the source of the trend. We propose an approach that detects the source of non-stationarity, which is based on quantifying the impact of non-stationarity in the mean and the variance via the semivariogram. By expanding the methodof- moments approximation of the semivariogram, we decompose the experimental semivariogram is into three terms: 1) trend in mean component, 2) trend in variance component and 3) stationary component. We can then assess the source of trend by calculating the contribution of each component at every lag. Two cases are presented to illustrate this tool. Firstly, a synthetic reference model is simulated and different trend patterns are added; the influence of these patterns in the experimental semivariogram calculation are analyzed and discussed. Secondly, a real dataset is considered where the impact due to the presence of trends in the mean and variance are assessed. The results of this paper reveal the semivariogram to be a tremendously powerful tool in determining the source of the trend. This insight may be useful in the selection of a suitable modeling approach for resource estimation.

Oct 1, 2009

By C. Sorel

The PAREX code has been developed since the nineties by CEA and AREVA to describe the PUREX process implemented in the French fuel reprocessing plants. It enables the calculation, either in steady or transitory states, of the behaviour of the different elements of interest at each process step. The high customized structure of the software allowed the implementation of various phenomenological models describing solvent extraction systems dedicated to uranium purification from crude ore to spent fuel. After qualification of the implemented models, the code was used to perform the design of flowsheets, for safety demonstration analysis or for operational assistance.

Aug 1, 2010

By B. S. Riess

A novel design for an automated uranium pellet stacking system is presented. This system is designed as a drop-in solution to the current production line to enhance the fuel pellet stacking process. The three main goals of this system are to reduce worker exposure to radiation to as low as reasonable achievable (ALARA), improve product quality, and increase productivity. The proposed system will reduce the potential for human error. This single automated system will replace the two existing pellet stacking stations while increasing the total output, eliminating pellet stacking as a bottleneck in the fuel bundle assembly process.

Aug 1, 2010