Search Documents

By Q. Shi, Q. Feng

"The influence mechanism of chlorite on the flotation of pyrrhotite was investigated through flotation tests, Zeta potential measurements, optical microscope photos, solution ion measurements and absorption measurements. It is observed that, the addition of chlorite influences the flotation of pyrrhotite seriously. The IEP (isoelectric point) of pyrrhotite and chlorite is 7.6 and 4.3 respectively, in the condition of slight alkalinity, both pyrrhotite and chlorite are negatively charged, and the hetero-aggregation will not occur. With the existence of oxygen in solution, the iron ions are dissolved from pyrrhotite surface because of the oxidation of pyrrhotite during pulp conditioning. The dissolved iron ions adsorb onto the surface of chlorite in the forms of iron hydroxyl and iron hydroxide, and the adsorption results in the opposite charge of chlorite surface. As a result, the hetero-aggregation between pyrrhotite and chlorite occurs. The adsorption of chlorite changes the surface property of pyrrhotite and restricts the adsorption of amyl xanthate onto pyrrhotite surface, and then decreases the flotability of pyrrhotite.INTRODUCTIONIn sulfide ores processing, magnesium silicate bearing gangue minerals often report to the concentrate causing downstream processing problems as well as increased smelting costs. Talc,chlorite and serpentine are gangue minerals commonly encountered in complex sulfide ores (Engel, Middlebrook, & Jameson, 1997; Pietrobon et al., 1997; Witney & Yan, 1997; Chen, Grano, Sobieraj, & Ralston, 1999a, 1999b; Bremmell, Fornasiero & Ralston, 2005; Senior & Thomas, 2005; Wang, Somasundaran, & Nagaraj, 2005; WieseHarris & Bradshaw, 2007). All of them are characterized with uniform crystal structures consisting of silicon-oxygen tetrahedron and magnesium-oxygen octahedron. The magnesium-oxygen octahedron layers are broken during the liberation of serpentine to expose the magnesium-oxygen bonds with strong ionicity and hydration, which results in natural hydrophilicity of serpentine. In water, the hydroxyl on serpentine surface ruptures and dissolves into the aqueous phase while the Mg2+ remains, resulting in surface positive charge (Tao, 2012). As serpentine has a positive potential at alkaline condition, it is therefore likely that it will attach through electrostatic attraction to the negatively charged mineral surface and reduce both the flotation rate and recovery of target minerals (Lu et al., 2011). For talc, characterized as good natural hydrophobicity, the liberation comes from the interlaminar fracture to remain molecular bonds on surface with weak hydration. Being naturally hydrophobic, talc easily reports to flotation concentrates, thus reducing concentrate grade (Shortridge, Harris, Bradshaw, & Koopal, 2000; Beattie, Huynh, Kaggwa, & Ralston, 2006). Meanwhile, both molecular bonds and magnesium-oxygen bonds are exposed on chlorite surface when liberation occurs, resulting in moderate natural hydrophobicity between serpentine and talc (Tao, 2012). And thus the mechanisms of influence of chlorite on sulfide ores are more difficult to study."

Jan 1, 2016

By J. Yue

The particle breakage kinetics, product size and size distribution, as well as grinding limit for quartz suspensions in a horizontal stirred mill are investigated. Results of grinding studies on quartz suspensions in a horizontal stirred mill confirm "first-order" particle breakage rates. A comparison of equation fits reveal that the product size distribution from stirred mill is best represented by the Rosin-Rammler equation when compared to the Gaudin-Shuhmann equation, but results fit poorly as particle size below five microns. A method of determining breakage rates versus particle size is demonstrated which shows that the 10% top size fraction is most appropriate for the determination of specific breakage rates. The method is used to demonstrate the relationship between particle breakage rate and particle size. As the feed particle size becomes smaller, the size reduction ratio decreases and approaches a grinding limit which depends on the effective stresses created in the mill.

May 1, 2004

By M. Wittke

"In the course of the extension of the railway network in Israel, currently the two 4.6 km long tubes of the Gilon Tunnels on the line from Akko to Carmiel are being constructed. The tunnels run through the limestones of the Bina- and Yirka-formations, which locally are karstified. The maximum overburden amounts to 160 m.The limestones are mostly horizontally bedded and vertically jointed. Occasionally also inclined joints exist. The tunnels cross various fault zones, which mostly strike at an acute angle to the tunnel axis and are steeply inclined. The karstic cavities which were encountered during tunneling have partially been filled by clay. In the vicinity of the fault zones, the rock has often been strongly jointed and weathered respectively. The two single-track tubes have a cross section with vertical walls and an open invert. The tubes are connected by cross cuts with a spacing of approx. 250 m.During the tender phase, WBI has elaborated the tender design for a joint venture of a Chinese and an Israeli construction company. After the joint venture had been awarded the contract, the preliminary and the detailed design have been elaborated by WBI and the construction works have been guided. On the basis of the geological description, rock mechanical models have been elaborated, followed by stability analyses on the basis of the Finite Element method. The tunnels have been excavated according to the shotcrete method. The support in most areas only consisted of a very thin shotcrete lining and radial bolts in the area of the roof. Depending on the degree of jointing and weathering, locally advancing support by means of spiles has been applied.The internal lining of reinforced concrete has been constructed in parallel to the heading of the tubes. Mucking and delivery of materials was carried out through the cross cuts.The breakthrough was achieved in April 2014 and thus within schedule. The predicted distribution of the excavation and support classes along the tunnel has been in good agreement with reality."

Jan 1, 2015

By H. W. Little

INTRODUCTION MINERAL deposits of Salmo map-area (Figure 1) have aroused the interest of prospectors for more than a half-century. Properties within the map-area have produced lead, zinc, silver, tungsten, and gold. Sheep Creek mining camp ranks fifth in the Province in the total production of gold, but during recent years interest has been concentrated upon base metals, and meticulous prospecting and exploration have resulted in the discovery of many large zinc-lead orebodies. PREVIOUS WORK Geological investigations of the region were begun long ago, and it is interesting to trace the development of ideas with our increasing knowledge of the geology of this complex area. The first geological examination of the rocks of Salmo map-area was made in 1859-60 by H. Bauerman (1), who was employed as geologist accompanying the first international Boundary Survey. Bauerman examined the rocks exposed along Pend d'Oreille river and published a section indicating that the sedimentary rocks are probably of Palaeozoic age, and are intruded by granite of unknown age. McConnell and Brock(2), in 1894 - 1900, carried out the reconnaissance mapping of the West Kootenay Sheet, on which they outlined the Mesozoic rocks of the Rossland Beaver Mountain volcanic groups that they believed rested unconformably upon the sedimentary rocks to the southeast, which they regarded as of Palaeozoic age.

Jan 1, 1951

By R. Roufail

Mineral liberation is accomplished by comminution and is the first step towards achieving successful downstream processes such as flotation or leaching. In metal mining, one of the most effective comminution methods that is used to grind particles below 10 microns is stirred milling. In this paper the study of particle breakage mode vs. mill operating parameters is addressed. Stirred mills' grinding action is mainly attrition, but operation can be manipulated to include breakage by compression or impact loading. Macro and micro analysis of particle breakage and grinding mechanisms are correlated. Macro analyses convey information that relates grinding mechanism to particle size and shape. It is speculated that the breakage mechanism in the horizontal stirred mills is massive fracture for the coarsest particles and attrition (abrasion) close to the grinding limit where the size reduction ratio approaches 1.0. For micro analysis, the particle breakage mode has a direct impact on fracture type either transgranular or intergranular. Intergranular particle breakage leads to higher mineral liberation compared to transgranular breakage. Similar minerals would have more homogeneous properties that convey a stronger bond compared to dissimilar, heterogeneous mineral bonds. Transgranular fracture requires higher energy than inter granular fracture; trans granular fracture toughness of pure single phase mineral is about 10-14 % higher than the intergranular fracture toughness. This communication presents the results of an investigation to assess how operating conditions can affect trans- vs. inter-granular breakage.

Jan 1, 2009

By D. R. Schmitt, N. Ong, R. S. Kofman

Shales and mudstones comprise about 75% of all the sedimentary rocks. In, particular, organic rich shales are considered as a petroleum source rock and more recently with the advent of hydraulic fracturing technology to be a reservoir in their own right. In this sense, the aforesaid motivates our work with laboratory measurements of elastic properties of these geologic materials, which are known to be anisotropic. As such, assuming Vertical Transverse Isotropy (VTI) symmetry, the dynamic and static moduli of a series of cores from various geological formations in Alberta, Canada are simultaneously investigated as a function of confining pressure using the ultrasonic pulse transmission method and strain gages. Dynamic moduli were obtained from ultrasonic P- and S-wave velocities measured on a prism cut with faces perpendicular, parallel and oblique to the assumed vertical axis of symmetry. Static moduli were calculated from strain-stress curves obtained along the directions perpendicular and parallel to the assumed axis of symmetry as well. Velocity measurements show that samples are highly anisotropic, but that the pressure-dependent behaviour of the wave speeds differs. VP(90°) and VSH(90°) both with layer parallel propagation and polarizations change little with pressure while VP(0°) and VS(0°) (both with layer perpendicular propagation) display significant nonlinear responses particularly at pressures < 25 MPa. These characters transfer to the derived full set of elastic constants. In order to effect a proper comparison of the dynamic and static moduli, we convert the dynamic elastic constanst to linear compressibilities pependicular (Kdyn1) and parallel (Kdyn3) which are directly comparable to the static tangent compressibiities obtained by differentiation of the observed strains. Both sets highlight the anisotorpic nature of the material but most interestingly Kdyn1 _ Ksta1 but Kdyn3 > Ksta3 by nearly 40% for one of the samples. The other samples measured respond similarly suggesting that conceptually the structure of such materials could be considered to be constructed of alternating stiff or compliant layers. This finding has implications in the response of the formation to stress particularly during hydraulic fracturing and the interpreation of acoustic logs in providing appropriate measures of elastic properties for engineering purposes.

Jan 1, 2015

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco&apos;s concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By S. J. van Rensburg

Competition for resources, including water and arable land, refocused attention on water and gold tailings management with respect to quantity and quality. MINTEK established and validated an "Advanced Leach Facility" to record kinetic leach information aimed at gold refractory sulphide ores. This facility was developed because of the need for additional leach process information to enable proactive decision making. Instead of focussing on optimised gold recovery only, the impacts of pre-oxidation methodologies were evaluated by considering key parameters, including cyanide speciation, reagent consumption, thiocyanate, arsenic, heavy metals, salt loads, water quality and residue stability. Results from oxidative leaching of a refractory gold ore employing oxygen, ozone, ultra-fine grinding, high shear and pressure oxidation are discussed. The relative cyanide and lime costs and environmental and sustainability effects associated with these technologies are briefly outlined.

Jan 1, 2011

By D. Y. Li, C. D. Ma, T. Zhou, T. J. Cheng

In this paper, a number of experimental tests are carried out to study the strength difference on rectangular prismatic marble specimens with different height-to-width (H/W) rations. The specimens have a nominal size of 45×15 mm in the compressive cross-section (W×T) and different heights (H = 22.5 mm, 45 mm, 60 mm and 90 mm). It is to say that the height-to-width ratios are equal to 0.5, 1.0, 1.33 and 2.0, respectively. The quasi-static uniaxial compressive tests are finished by a servo-controlled INSTRON machine (the strain rate at about 10-5/s), and the dynamic compressive tests are finished by a diameter of 50 mm cylindrical SHPB apparatus (the strain rate reaching about 101/s). The rock failure process of marble specimens is captured by a high speed camera in order to distinguish the fracture propagation behaviour. It is found that the compressive strengths increase when the H/W ratio of marble specimen changes from 2.0 to 1.0 due to the end clamping effect both for quasi-static and dynamic loads. However, when the H/W ratio changes from 1.0 to 0.5, the apparent compressive strengths decrease both for the two loading conditions. The strength decrease of short marble specimens may be attributed to the change of failure mode from shear to slabbing, which can be identified by the fracture patterns of the specimens. Based on the uniaxial compressive tests, the slabbing strength of the marble was found to be about 40% of its UCS for the specimens with a nominal height-to-width ratio of 2.0. In addition, it is found that the dynamic increase factors (DIF) are affected by the specimen’s aspect ratios. It implies that the same aspect ratios should be used to compare the dynamic and static compressive strength of rocks. Meanwhile, both the static and dynamic tensile strengths of the marble are obtained by the Brazilian disc tests. The ratio of the dynamic tensile strength to the static tensile strength of the marble is about 2.68.

Jan 1, 2015

By Samuel Nunoo

Gibraltar Mine is an open pit copper-molybdenum mine in central British Columbia. The stability and potential failure modes of pit walls in the Granite Pit are controlled by the orientations of joints and faults. The structural geology also has an impact on as-mined bench geometries. Geotechnical mapping and surveying were conducted using stereo photographs and photogrammetry software. Detailed digital terrain models were constructed to determine the pit wall geometry and the locations and orientations of larger structural features. The pit wall geometry is compared to conventional survey results and the mapped structures are compared to results from a nearby geotechnical borehole.

Aug 1, 2013

By R. Gordon, J. Palich, W. Qian

The EarthProbe DCIP system deploys tightly spaced electrodes connected to a centralized data acquisition system that enables arbitrary selection of current and potential electrodes through relays. Rapid data collection (approximately 1000 readings per hour) and advanced signal processing allow for efficient use of conventional and novel arrays and the removal of natural and cultural noise. What is unique about the system is its electrode and borehole cable design, which allows seamless integration of borehole and surface measurements. EarthProbe operates in four configurations - surface, borehole, borehole-to-borehole, and surface-to-borehole (a variant of the borehole-to-borehole configuration).

Jan 1, 2011

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By F. Osmond, R. Kelly

"Malcolm Knowles, the famous adult educator once wrote: ""What a challenge we in human resources development face if we are to avoid the obsolescence of our workforce. I can foresee this challenge requiring that we reconceptualize (...) and redefine the role of HRD, away from that of managing the logistics of conducting training activities to that of managing a system of learning resources"".The context in which this was written surrounds the subject of adult education and the need for business and industry to change its approach to the treatment of adults as learners. In explaining what &apos;managing a system of learning resources&apos; means, Knowles refers to line supervisors and managers as the most ubiquitous resources for day-in and day-out employee development. In many organizations training has been largely a staff rather than line responsibility. Even where trainers reported to line management, it was still seen as a staff function performed by a few specialists.This change referred to by Knowles places a much heavier responsibility on line supervisors and managers for the development of their personnel than has traditionally been the case. Managing that change - handing over the responsibility to the line organization - is the supreme challenge for the HRD function.Just why is this change necessary? Because too often, the learner does not effectively use on the job what he or she learned in the classroom. In fact, learners often discard new methods and revert to the older ways. The reason training does not stick is that the systems for training and work management are most often separate entities and while one may support the other, they need to be a single integrated system in order to ensure the transfer to the job effectiveness of training and some real value for the training dollars.Because much training can be wasted, steps have to be taken to ensure that it fulfills its intended purpose. The effective and continuing application of knowledge and skills that learners acquire can only be realized when line supervisors and managers are at the centre of the training system.This paper describes how such a systemis being developed at the Iron Ore Company of Canada (IOC) as a functional training program is introduced. The following text provides background information on the IOC - who they are and where they are located, a definition of functional training, an evaluation of the suitability of this approach for adults in industry, a description of how the program is being implemented at IOC and some observations that have been made as this change is experienced."

Jan 1, 1995

By D. Bouchard, J. Langlais, A. Lemieux, N. Andrade

A concerted effort between Akan International Limited and the National Research Council of Canada (NRC) has been initiated to develop a liquid-based slurrymaking process, dubbed SEED (Swirled Enthalpy Equilibration Device) for semi-solid forming. The technology is presently entering the industrial and commercial stages, and will be used by the first customers at the end of 2006. Semi-solid processing of aluminium alloys offers many advantages in fabricating economically near-net-shape parts of superior quality. The SEED process helps to overcome problems experienced with thixocasting and especially the high cost of feedstock. The SEED process involves two main steps: 1) heat extraction to achieve a desired liquid/solid mixture, and 2) drainage of an excess liquid to produce a self-supporting semi-solid slug that is formed under pressure. The heat transfer plays an important role (enthalpy equilibrium) during the manufacture of the semi-solid slurry and its analysis is briefly described. The semisolid material is obtained using different processing times and initial conditions. The impact on the solid fraction distribution and the morphological evolution of the microstructure is presented. The influence of the SEED processing parameters (slurry preparation) and the resulting mechanical properties for the alloy A356 are also reported.

Jan 1, 2006

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By P. Radziszewski

Industrial practice in mineral processing shows that an important problem in understanding and monitoring in-mill parameters is due to the lack of fundamental knowledge and appropriate sensors. With the development and growing use of DEM charge motion simulators for mill optimisation and design, it is possible to describe the fundamentals of grinding mill behaviour, in improving the understanding of internal grinding mill dynamics and in developing solutions to industrial practice. The main challenge to bringing this DEM technology to the mill operator however was the need for substantial computing power and time. However, what about a simplified DEM charge motion model running in real-time? What about the use of sensor technologies to correct any possible drift in simulator prediction? Could such a technological system be used to predict mill performance and eventually be used for mill control and optimisation? Some of these questions are answered with the development of an "on-line" DEM charge motion simulator package (SAGTools?) along with that of a number of sensor technologies (liner wear, acoustic, instrumented ball) that can contribute to simulator precision. With the objective of bringing this modelling and sensor technology into the concentrator control room to assist operators, this paper aims to describe the main elements of this emerging and developing technology and discuss how it can lead to online mill performance prediction and eventual control.

Jan 1, 2007

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004