Search Documents

By R. St. C., G. E. Morris, M. Zbik, Smart

Effective flocculation and dewatering of slurry streams containing clays (particularly kaolin and smectites which are often <200nm in lateral dimension) is becoming increasingly urgent. Release of water (often >75 wt%), for recycle and reduced make-up water consumption, from slurries in tailings streams and dam beds is usually slow and incomplete. Changes in settling rates and solids density of tailings containing clays can be achieved in practice by changes in pH, dissolved cations and flocculant additions. To achieve fast separation of clays from water and minimization of retained water, individual particles need to be bound in the initial stages of thickening into large, high-density aggregates, which may sediment more rapidly with lower intra-aggregate water content. Quantitative STIMAN (STructural IMage ANalysis) cryo-SEM imaging, shows that the structure of aggregates formed before flocculant addition has a determinative effect on these outcomes. Without flocculant addition, 4 stages occur in the mechanism of primary dewatering of kaolinite: initially separate particles and aggregates are dispersed (<0.3GP, where GP is the gel point); a partially-gelled chain network then forms linking particles edge-edge (EE) still well below the OP but remains largely suspended; after an induction time, this network structure rearranges from EE to face-face (FF) contacts densifying, compacting and dewatering the aggregates with settling rates well above Stoke&apos;s Law estimates for >20µm particles or aggregates; the GP is rapidly reached during settling producing a network spanning the vessel with compressive strength. This sponge-like structure with EE oriented particles limits slurry dewatering because the steric effect in the resulting partially-gelled structure is much more dominant than the electrostatic effects predicted by DLVO theory. Van der Waal&apos;s forces at very close distances, as particles slide across each other, may be responsible for the EE to FF change in structure. In this way, the previously extended network contracts, and when the solid volume fraction is low, the continuous network breaks apart forming aggregates and aggregate associations as flocs which arc able to freely settle. These densified aggregates settle at increased rate, give lower bed density and retain less water after drainage. With flocculant addition, the internal structure and networking of the pre-aggregates is largely preserved but they are rapidly and effectively bound together by the bridging action of the flocculant(s). The STIMAN analysis shows that there is a inverse correlation of intra-aggregate porosity (and void permeability) with Darcian permeability (and extent of dewatering) whereas there is a strong positive correlation of Darcian inter-aggregate permeability with settling and primary dewatering rate.

Jan 1, 2004

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By Thomas Hauquin, Olivier Deck, Yann Gunzburger

"In this study, 2D numerical modeling of a room-and-pillar mine is conducted along with the calculation of all terms of the mechanical energy balance. Simulations of different geometrical and geomechanical configurations are performed in order to investigate the conditions that favor a high seismic energy release (instability) during the excavation (removal) of one single pillar. At first, classical stressstrain simulations enable us to estimate the elastic and quasi-static response of the mine. Then, owing to the implementation of new functions in the modeling code, the seismic energy released when the pillar is removed is calculated. The obtained values are found to be in agreement with those calculated analytically using a modified energy balance based on the works by Cook (1967) and Salamon (1984).It is shown that the mine’s proneness to release large amounts of seismic energy, after sudden removal of one single pillar, mainly depends on three parameters: the initial extraction ratio of the mine, the depth of the exploited seam and the Young’s modulus of the surrounding rock mass compared to that of the ore. Moreover, it is pointed out that the magnitude of the seismic energy can be greater than that of the stored elastic energy, meaning that the dynamic (seismic) transient stresses should not be neglected when compared to the quasi-static stresses, particularly when trying to prevent the risk of rockburst and collapse in underground mines."

Jan 1, 2015

Adaptive Processing as proposed in geometallurgy has to rely on spatially interpolated information on geometallurgical parameters like phase composition, size distributions of particles of different phases, grain shape parameters, and portions of value elements in different grains. Using the geostatistically predicted values for adaptive processing, e.g. for the selection of milling diameters, thresholds in physical separation, or choices on using an extra pre-separation step, is typically not optimal. Mathematically this effect is introduced by two forms of nonlinearities: 1) The nonlinear scales of compositions, distributions, and shapes have special properties with respect to geostatistics. Classical geostatistics creates some artefacts for these nonlinear scales. On the other hand, modern geostatistical procedures adapted to these scales do not provide unbiased results with respect to linear transformations of the data (e.g. biased block estimates). 2) Neither economic nor ecological effects (e.g. monetary gain) of processing decisions are linear in the interpolated geometallurgical parameters. These nonlinear transforms are not unbiasedly estimated by the likewise transformed unbiased geostatistical predictions of the geometallurgical parameters. Furthermore, we need to optimize the conditional expectation of the gain, rather than obtain an unbiased estimate. Standard geostatistics as such does not provide the "right sort" of estimates for adaptive processing. A nonlinear kriging procedure is needed to approximate the nonlinearities mentioned before. We propose to solve these problems simultaneously using a nonlinear geostatistical technique for predicting the target function (the monetary gain), rather than to predict the geometallurgical parameters and compute the gain from them. The optimization can then be performed directly on this estimated function. It can be shown that this optimization performed on the conditional expectations, not on unbiased predictions, would yield the best possible processing choice. We propose a procedure choosing the processing parameters on an approximation of the conditional expectation. The difficulties with the classical approach and the effectiveness of this new approach are illustrated by a simplified simulation example with a single processing parameter and a simple dependence on the microstructure.

Aug 1, 2013

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By A. Eslami, H. Tabatabaei, M. Kolandoozan, Z. Manafi, A. R. Shahverdi, M. Noaparast, M. Oliazadeh

Application of Acidithiobacillus ferrooxidans bacteria to flotation of Sarcheshmeh low-grade copper sulphide ore was studied. Sarcheshmeh low-grade ore contains pyrite, which causes some problems in the flotation of copper minerals. In this study, A. ferrooxidans was used to change the surface chemistry of pyrite and copper sulphide ores and consequently, their flotation behaviour. In the presence of A. ferrooxidans and xanthate as a collector, pyrite was depressed whereas chalcopyrite and other sulphide minerals were unaffected. In addition, the pulp pH remained unchanged. It was shown that the surface chemical properties of the bacteria can be manipulated successfully to achieve the desired effects in a flotation process. The results showed that the recovery of pyrite in the presence of the bio-depressant is 50% lower than when no bacteria were present. At the same time the recovery of chalcopyrite remained unchanged.

Jan 1, 2004

By G. A. Barclay

"I - INTRODUCTIONSteel castings still comprise the largest volume of wear materials used in crushing and grinding in the Canadian mining industry. The range of impact and wear properties possible with steel castings enables them to be used successfully in both high impact crushing as well as milling where abrasion resistance is the main criterion. Approximately 15,000 tons per year of steel mill liners and crusher castings are used by Canadian mines.The properties of the main steel casting alloys used - manganese, pearlitic chrome-moly and martensitic medium carbon steels will be discussed with reference to their applications. Field data on a new application in primary gyratory crushers for martensitic medium carbon steels is presented. Liner wear life and mill efficiency can be improved through proper liner design.The liner wear pattern can be used as an indication for liner profile changes to improve wear life. Changes in liner configuration can improve through put and use of larger castings can reduce downtime. Casting performance can be improved and foundry production costs reduced by adopting certain design improvements.II - ALLOYS USEDTable I list the most common ferrous liner materials used in relation to their hardness and wear resistance (1). The most wear resistant materials are the irons at the top. In many applications the service impact exceeds the impact strength of the irons and tougher less wear resistant steels must be used. The impact resistance improves from top to bottom with manganese steel the toughest. The hardness of the martensitic steels approaches that of the Ni-Hards however the wear life, because of the absence of carbides, is less."

Jan 1, 1983

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By O. Bouaziz, O. Magnea, P. Cugy, E. F. Rauch

The experimental difficulty to perform Equal Channel Angular Extrusion (ECAE) of a bulk sample of hard material such as steel was overcome. The original method proposed in this paper consists in replacing the bulk sample by a stack of alternated hard metal (steel) and soft metal (aluminium) sheets. By applying this procedure to an Interstitial Free steel (IF steel), 2.7µm grain sized material was obtained after recrystallisation. Its mechanical properties (hardness, formability in shear, hardenability and faigue limit) were investigated and compared with the properties of the same IF steel with conventional grain sizes (12m and 25µm).

Jan 1, 2004

By J. H. McKibbon

This paper outlines the basic steps in the sizing of electrostatic precipitators according to the Deutsch equation. Design parameters that do not appear in the equation are also described.

Jan 1, 1971

By R. A. L. Drew, F. Jalilian, M. Jahazi

Joining of superalloy Inconel 61 7 with a foil interlayer using transient liquid phase bonding (TLP) technique was studied. Inconel 617 is a solid solution, Ni - Cr - Co- Mo alloy with an exceptional composition of high temperature strength, oxidation, carburization resistance and thermal stability. In this investigation, two bonding temperatures, 1065°C and 1150°C, and two interlayer thicknesses with joining times varying from 5 minutes to 24 hours were employed. Experiments were carried out using nickel base interlayer (A WS BNi-3) with boron as the melting point depressant (MPD) element. Joints were characterized using optical microscopy, SEM, FEG-SEM, EBSD, XRD and microhardness. The results indicated that the rate of elimination of the liquid phase with increasing the bonding temperature, holding time and decreasing the thickness of the interlayer increased. The main precipitates in the diffusion layer had platelike and blocky morphologies for both bonding temperatures and all holding times.

Jan 1, 2006

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be &apos;designed&apos; to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By C. A. Pickles

Nickeliferous limonitic laterite ores contain considerable free moisture. In this research, the application of microwave radiation for the drying of this ore was investigated. The effects of sample mass, initial moisture content and porosity on the microwave drying rate were studied and the results were compared to those obtained with conventional drying. Microwave drying rates of two to three times the conventional values were achieved. Further enhancement of the microwave drying rate was realized by increasing the flow rate of air over the sample or by operating at reduced pressure. The high microwave drying rates were attributed to the inverted temperature gradient which resulted in internal heating and boiling and this in turn promoted movement of the water, both as liquid and vapour, to the surface.

Jan 1, 2005

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By J. Gillies

"Those of you who were at last years C.M.P. meeting are aware there was discussion at that meeting concerning the best method of assisting the assayers of metal mines to exchange new ideas and methods of assaying. The opportunity to advise you of what came of that discussion is very much appreciated.There are several societies, including the Chemical Institute of Canada, the Spectroscopy Society and others that could be of some assistance to assayers. However, since these societies cover a rather broad field and not many mine assayers have the opportunity to attend their meetings, it was felt that an organization oriented to the specific needs of the mine assayers would be of more value to them.Several years ago an attempt was made to hold meetings for the benefit of assayers in conjunction with the Conference of Metallurgists held each year by the Metallurgical Society of the C .I.M.M. This did not work because very few of the mine assayers attended the meetings.With the very evident success of the type of meetings the C.M.P. have and the excellent groundwork done by your secretary, Mr. Stevens, in talking about this to mine management and assayers at many mines across the country, it was decided to hold a meeting at Noranda on October 8 to discuss how best we could help ourselves solve our problems.For the initial meeting it was felt that perhaps it would be better to start with a smaller group, so invitations were sent to mines in Ontario and Quebec that were geographically fairly close to Noranda."

Jan 1, 1970

By W. J. Gibson

"This paper will provide a general assessment of the differences in construction and industrial labour relations. From this outline will come a detailed examination of labour relations in the construction industry and then specifically as related to the construction of mining projects, with emphasis on projects in isolated areas. Development of manpower forecasts, manpower availability, wage escalation formats, working rules, training and recruitment programs, and safety - as related to construction labour relations in the mining industry - are topics which will be dealt with."

Jan 1, 1972

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By Yusuke Yamamoto, Mineo Asano

"The present study investigated the texture transition during secondary recrystallization in the AA5182 sheet. During the initial stage of annealing, the texture showed a weak Cube orientation as the primary recrystallization texture. During the secondary recrystallization with abnormal grain growth, the area ratio of the {hkl} <011> orientations increased by consuming the other orientations. The texture transition was calculated by the 2-D Monte Carlo simulation with the misorientation dependency. When the higher grain boundary mobility was set in the specific range of the high angle misorientation, the orientation preferential growth of the RW {100} <011> orientation was reproduced. However, other {hkl} <110> orientations could not be well reproduced by the misorientation dependency.INTRODUCTION Crystal orientation and texture are important factors for aluminum sheet products from the standpoint of mechanical property, formability and isotropy. The recrystallization texture results from the orientation preferential growth from the rolling deformation microstructure and the texture (Alvi, Cheong, Suni, Weiland, & Rollett, 2008). Texture development has been a topic of intense research for decades with advances in analysis methods, e.g., orientation mapping (OIM) and computer simulations (Fjeldberg & Marthinsen, 2010; Ivasishin, Shevchenko, Vasiliev, & Semiatin, 2006). The grain boundary characteristic is considered to be a key for the orientation preferential growth. In the case of the recrystallization from the deformed microstructure, not only the grain boundary characteristic, but also the dislocation density and the subgrain size affect the nucleation and the grain growth (Engler, Löchte, & Hirsch, 2007). On the other hand, in the case of secondary recrystallization, the dislocation density and the subgrain size can be ignored and the effect of the grain boundary characteristic can play a significant role in the grain growth. There is intense research about the texture development during secondary recrystallization in aluminum alloys and it was reported that coarse {hkl} <011> grains were formed during the secondary recrystallization (Suk, Shin, & Huh, 2006; Rios, & Gottstein, 2001). However, the mechanism of forming the {hkl} <011> grains has not been fully clarified. In the present study, the effect of the grain boundary characteristic on the orientation preferential growth was investigated by EBSD analysis and Monte-Carlo (MC) simulation."

Jan 1, 2018