Search Documents

By Abhilash

Uranium is conventionally extracted using a process that employs strong acid (H2SO4) and an oxidant (MnO2) as leaching agents. This method often creates environmental problems, requires large amounts of energy, and involves a complex operational plant. It is not, however, economically attractive to extract uranium from low-grade ores by chemical leaching. Because the content of U3O8 in the Indian ore is usually below 0.1% by weight, it is necessary to develop an alternative process to enable the efficient and economic recovery of uranium. Uranium ore from the Narwapahar mines, UCIL is a type of vein deposit found in India, which accounts for ~54% in India. The ore (0.047% U3O8), though of Singhbhum area, possess exceptionally different mineralogy due to presence of some refractory minerals and richness of apatite (5%) resulting in a maximum 78% recovery through conventional processing at UCIL, with a very high consumption of sulfuric acid and pyrolusite, besides possible loss of uranium as uranium phosphate. To avoid usage of environmentally non-benign oxidants, remediation of influence of phosphates, and improve the overall process output of uranium; an alternate extraction technology using microbial isolate(s) is worthwhile exploring and the same is presented in the paper. The microbial isolate enriched with Acidithiobacillus ferrooxidans grown from source mine water was employed for bio-leaching of uranium while varying pH, pulp density (PD), particle size, etc. On varying pH at 35oC using 20%(w/v) PD and <75µm particle size, 83.5% and 78% uranium bio-recovery were observed at 1.7 and 2.0 pH in 40 days against maximum recovery of 46% and 41% metal in control experiments respectively. Whereas, it was observed that grinding of ore to finer size actually helped dissolution of uranium. Finer size particles (<45µm) gave a maximum biorecovery of 93% in 40days at 10%(w/v) PD, 1.7 pH and 35oC. The bio-recovery of uranium fell down from 93% to 82.73% and 60% on increasing the pulp density from 10% to 20% and 30% respectively for particles of <45µm size. The higher uranium dissolution during bioleaching at 1.7pH can be correlated with increase in redox potential from 433 mV to 664mV in 40 days.

Aug 1, 2010

By George Kellock

In presenting this paper for discussion at the Western Annual Meeting to be held in Edmonton, it is with the idea of creating a full and general discussion by the mining men in the Province as to the best way to eliminate, or at least hold down to a minimum, the dangerous coal-dust which is made in mining pitching seams in our Alberta mines by the chute method. Also, an alternative method is outlined, whereby the percentage of lump-coal mined can be increased, and the mining costs reduced-although the paper does not go into any detailed consideration of costs. The general trend of mining practice and lay-outs is at present towards mechanization, and the results being accomplished by the substitution of machines for manual labour are fully justifying the changes. In the technical mining journals, there are published from time to time papers dealing with a variety of methods of mining, which are descriptions of actual operations, and a great deal of interesting and valuable data is given as to the comparative values of the different methods, insofar as the percentage of grades of coal produced, the cost of production, etc., are concerned; but the mechanical methods described in these papers are nearly always suitable only for flat seams, or seams with a very low inclination.

Jan 1, 1929

By Ernest Becker

Golder Associates provided overall radiological direction and assistance to the client in their interactions with the Canadian Nuclear Safety Commission and operational radiation protection services for the remediation of a calciner that had been used to process uranium. The project was somewhat unusual in that the radioactivity from within the calciner room was removed from the site and the cleaned steel recycled. The presence of yellowcake within the process equipment required stringent radiation protection measures. This project was completed successfully with minimal radiation exposures to the workers and the effective protection of the environment.

Aug 1, 2010

By P. M. Chapman

Risks to aquatic receiving environments from uranium mining and milling fall into three categories: physical (habitat change), chemical (e.g., uranium, selenium, total dissolved solids [TDS], metals including vanadium), and radiological. Although all categories of risk need to be managed, chemical risks are the most significant and are typically chronic rather than acute. For instance, selenium toxicity is primarily manifested as reproductive impairment due to maternal transfer, resulting in embryotoxicity and teratogenicity in egg-laying vertebrates. Risk is best assessed using a weight of evidence approach focused on ecosystem services. Risk management should be based on both risk assessment and adaptive monitoring.

Aug 1, 2010

By P. Maltais

Over the last 10 years, Computer Aided Design, Finite Elements Analysis and field testing of prototypes have enabled the cycling industry to grow and to significantly improve its products. However, today&apos;s cyclists have become more and more demanding, making these classical design approaches almost obsolete. Devinci understood that problem four years ago and fully revisited its design approach; to offer bicycle frames better suited to real life riding, one must fully know those real life conditions. In partnership with the University de Sherbrooke, Quebec, Canada, Devinci then developed a bicycle enabling them to measure the actual load applied on a bicycle frame in real-time for real riding conditions: the instrumented bike. Today, Devinci uses its instrumented road and mountain bikes, combined with virtual prototyping and laboratory testing capabilities to develop better bicycles, faster.

Jan 1, 2006

By K Morrison

Different individuals have calculated the boundary stresses around elliptical openings in an infinite elastic medium for various conditions of loading. With caution, such calculations are useful in indicating stress trends in mining. This paper illustrates an application to caving operations and suggests that abnormal field stress would have an adverse effect. Introduction GELDART and Udd (1), applying elastic theory, confirmed, and set out graphically, the stress distributions on the surface of elliptical openings with axis ratios varying from 1.0 (a circle) to infinity (a crack). The loading conditions varied from uniaxial to hydrostatic, and inclinations for the opening, with respect to the stress axis, varied from 0° to 90°. As most mine openings can be generalized into this elliptical conception, the usefulness of the presentation lies in the fact that given reasonable estimates for the stress ratio, the axis ratio, and its inclination, then the trend in stress concentrations as an opening develops can be readily approximated.

Jan 1, 1964

By Y. Chunhua, L. Chunsheng, W. Sheng

"Countercurrent solvent extraction is the dominant industrial rare earth separation method. For the rare earth separation, with low separation factors and multiple components, designing and optimization plays an important role in reaching product quality and reducing separation plant costs. Based on the theory of countercurrent extraction, cost-efficient methods, such as third-outlet separation and hyperlinked extraction processing, have been introduced following computer simulation. The consumption and fixed investment of industrial practice are compared, by which advantages of the optimized rare earth separation process are indicated. INTRODUCTIONThe rare earths (RE) have outstanding optical, magnetic and electric properties in advanced material applications and have therefore received much international attention in recent years. Liquid-liquid extraction is the major industrial RE separation method and is widely used in the industry. Supported by the government and with collaboration from the institutions and enterprises, China has made great progress in RE separation, and has become the dominant supplier of separated RE products. Complicated by multiple elements and low separation factors, careful design of RE separation processes is vital for the quality and cost of production. The theory of separation is the key to basic of flowsheet design and industrial applications.BASIC SEPARATION PROCESS AND THEORYGeneral ProcessAcidic extractants such as P507, P204 and naphthenic acid, are the most popular extractants in modern RE separation industry. In the general separating process, the extractant is saponified with a base, then ion-exchanged with RE solutions, thereby to provide stable and high RE loading in the extractant to fulfill the requirement of production quantity and quality. The RE-loaded extractant is then countercurrently extracted and scrubbed with RE solutions and the RE element thereby is purified. After the countercurrent extraction process, the RE-loaded extractant is stripped with acid to obtain an aqueous RE product, and prepare the extractant for recycling (Xu, 1995)."

Jan 1, 2012

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By L. Voisin, K. Mühlenbrock

A new pyrometallurgical process is proposed for cleaning complex copper matte and for recovering copper from copper scrap containing lead. In the process, a given amount of pig iron is added to the complex material under a reducing condition to produce two or three liquid phases at the equilibrium, depending on the content of sulfur in system, of copper-rich and iron-rich alloys, and matte, respectively. The novel process is proposed based on the experimental results obtained by performing laboratory scale tests in an electrical furnace at 1473 K followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Atomic Absorption Spectroscopy (AAS), Inductively Couple Plasma (ICP) and Carbon Infrared Spectrometry (CIS) techniques. The results were discussed on the basis of the distribution of lead as impurity in the miscibility gap where equilibrated phases coexist. According to the mass balance calculations, the elimination of lead into the iron-rich alloy phase as a harmless and smaller deposit might be feasible and the process proposed for cleaning the complex matte would be promising.

Jan 1, 2014

By T. B. Williams

Most geologists have felt the need of a longer base than is ordinarily available when using a Brunton compass or other convenient instrument for taking strikes and dips in the field. To overcome this difficulty a lath or stick with straight parallel sides is frequently used. This accessory adds to the accuracy of the work, but it is a decidedly inconvenient one for the geologist to carry, especially if he be heavily loaded or is travelling on horse-back or through thick brush on foot. The writer has abandoned its use in favour of a sturdy two-foot carpenter&apos;s rule. The rule preferred is manufactured by J. Rabone and Sons, Birmingham, England. It is provided with a good level-bubble set in one of the limbs, and a scale, of the protractor type, graduated to five degrees through 180 degrees, attached to the main joint at the middle of the rule. (See Figure 1). For an instrument of its kind it is very accurate, and, in addition to the uses mentioned below, it &apos;is a handy thing to have around any camp. It is frequently used when plotting roughly in the field and for a protractor when one is not available. When not in use it may readily be carried in the top of the high-boot or legging. Ordinary strikes are measured as illustrated in Figure 1, the compass being held against the rule, which is in a horizontal position. Dips may be measured in a corresponding way by holding the Brunton compass against the extended rule, which is thus used merely as a straight edge. It is usually much more convenient, however, to ? use the rule only for this purpose, in which case one foot of the length rests as a straight-edge against the rock surface. This adaption is shown in Figure 2.

Jan 1, 1929

By S. Castro

Hydrolysis of metallic ions depends on pH and the products of hydrolysis either activate flotation or can lead to inadvertent activation of gangue particles, but can also depress flotation of valuable components. One of the most recently studied topics is the use of seawater in flotation. Seawater is a concentrated NaCl solution (about 0.6 mol/L) that also contains considerable amount of Mg2+ and Ca2+ ions. The hydrolysis products of Mg2+ strongly depress flotation of molybdenite over the pH ranges over which they form in the process water. This effect can be eliminated by removal of hydrolysing ions from the process water or by carrying out the flotation at the pH over which such a hydrolysis can be avoided. The former can be exemplified by prior precipitation of the harmful hydrolysing ions as, for example, in the University of Concepcion Patent. The latter can be exemplified by the use of metabisulfite to depress pyrite in the flotation of Cu-Mo sulfide ores in seawater, the process that is carried out at much lower pH, which avoids formation of Mg2+ hydrolysis products.

Jan 1, 2017

By H. L. Cameron

General Statement In July, 1948, experimental aerial photography o shallow water zones on Northumberland strait was carried out by the Nova Scotia Research Foundation. This work was designed to test the feasibility of aerial photography for coastal surveys o various types, including seaweed and bottom detail surveys. In the course of the work at Lismore, undersea faulting was noted visually and was later clearly apparent in the photographs. In order to prove beyond doubt that the lineations photographed are actually faults, a ground check was made, and terrestrial stereoscopic photographs were obtained of these features where they intersect the shore line. There can be no doubt of their nature, and the type of faulting is probably thrusting due to compressive forces. This is indicated by the successive right- and left-hand displacements on intersecting faults. The age of the fracturing is post Lower-Pennsylvanian (Lismore) and is correlated with similar compression faulting in western Cape Breton. As far as can be ascertained, this is the first time that subsea faulting has been photographed, though it is quite possible that similar structures have been observed elsewhere. Location and Area Lismore is on Northumberland strait, approximately thirty-five miles east of Pictou (see index map, Figure 1). The area mapped from aerial photographs (Figure 2) is a strip approximately two miles long by a quarter of a mile wide. Figure 3 shows a stereo-pair of the aerial photographs used to construct this map. The terrestrial stereoscopic photographs (Figure 4) show one of the faults.

Jan 1, 1949

By J. M. B. Scarborough

This paper deals with measures taken to maintain effective operation of heavy-duty equipment in open-pit mining. at Pine Point, N.W.T., during periods of extreme cold weather. The points covered include equipment modifications designed to improve cold-weather performance, effective lubrication of machinery that is vulnerable to extreme cold and operating procedures designed to prevent equipment damage.

Jan 1, 1966

By E. G. Langille

"The Premier mine; owned by Silbak Premier Mines; Limited; is 14 miles from Stewart at the head of Portland canal. Development of the property began in 1918; and since chat time a very large amount of gold and silver as well as some lead and copper have been produced from the mine.The area in the vicinity of the mine is underlain by greenstones tuffs, and sediments of Mesozoic age, belonging to the Bear River formation of the Hazelton group. These rocks are intruded by a stock 2 miles in diameter, composed of orthoclase porphyry and called the Premier porphyry. It sends numerous sill-like and dyke-like tongues into the Bear River formation, and is intruded in turn by a granodiorite outlier of the Coast Range batholith. The orebodies occupy fractures and fracture or shear zones. Primary ore consists chiefly of pyrite, galena, and sphalerite, with some chalcopyrite. The upper 300 feet, or locally 600 feet, contained presumably secondary silver minerals."

Jan 1, 1954

By W. Lodge, G. Rasmussen

"The carbon-in-pulp (CIP) process has been the dominant gold recovery technology since the 1980s. During all this time carbon measurement, and control of the carbon transfer pumps has been largely manual in nature. Such manual operation inevitably limits process efficiency, potentially resulting in higher gold solution losses, and higher cost of circuit operation. Based on the authors’ experience, average plant solution loss is in the range of 0.02-0.03 ppm Au, as opposed to the general industry target of 0.01 ppm Au or less. Gekko Systems, in conjunction with Curtin University’s Gold Technology Group, has developed a carbon concentration meter, the ‘Carbon Scout’ meter. The meter automatically measures carbon concentration in all tanks, providing more frequent and more precise data. Combined with SIMCIL, a CIP circuit process model which is used to determine the optimum set points for the circuit, the meter should ensure lower gold solution losses, and more efficient operation of the carbon circuit. This paper will review they critical factors for good carbon management, the development of the meter and results from the first plant installation. Additional benefits of the Carbon Scout, including improved health and safety and the opportunity to measure other key variables in the leach/adsorption circuit from one central location will also be described.INTRODUCTION The carbon-in-pulp (CIP) process was first introduced to the gold industry in the early 1950s at the Carlton Mill in the USA (Fast, 1988), with the modern version of CIP becoming fully developed with large scale installations in South Africa in the late 1970s (Laxen, 1982). CIP quickly became the technology of choice for new operations, and for the retrofitting or upgrading of existing operations. In the 1980s the carbon-in-leach (CIL) circuit configuration became the process design of choice due mainly to its lower capital costs. With 40 years of operational experience, CIP/CIL for gold recovery is now mature a technology, whose operations and limitations are well understood. To extract further efficiencies from such technologies, by improving recoveries and/or reducing operating costs, is challenging and may require new approaches to circuit management. Gekko Systems, in association with the Gold Technology Group at Curtin University, has developed the Carbon Scout, an automated carbon measurement device. This device replaces manual measurement of carbon concentration in carbon adsorption tanks, providing more frequent and more accurate data for control of the CIP process. Data from the Carbon Scout can be used to automatically control the carbon forwarding pumps."

Jan 1, 2018

By C. Bernier

This paper deals with three major problems associated with mining operations during the winter. These are the maintenance of the cooling systems of diesel engines, the high incidence of hydraulic dump failures on packaging machines, and the build-up of frozen fines on wet-ore conveyor belts.

Jan 1, 1966

By O. Hyvärinen

Outokumpu has developed a new chloride leaching process called HydroCopper®. In this process copper sulfide concentrates are leached at atmospheric pressure in concentrated sodium chloride solution using cupric ions as the oxidant. Copper is recovered from the purified leach solution by precipitating cuprous oxide, which is then reduced to pure copper and further melted and cast directly into copper products. The key reactants: sodium hydroxide, hydrogen and chlorine are generated from the spent sodium chloride using chlor-alkali technology. An important feature in the HydroCopperTM process is that the gold contained in copper concentrates is leached as chloride complexes and recovered from solution by activated carbon. Conditions for the leaching of gold-bearing pyrite can also be achieved in the chloride system by optimizing the redox conditions. This paper deals with the basic factors affecting gold leaching from copper sulfide concentrates. Opportunities for the recovery of refractory gold associated with arsenopyrite and pyrite will also be discussed.

Jan 1, 2005

By LeRoy A. Thorssen

The use of lightweight aggregate as a constituent of concrete is not a recent development. Pumice was used by the early Romans, in pozzolana cement concretes, in the construction of many of their works. However, the recent development of manufactured lightweight aggregates, such as the expanded shales, vermiculite and perlite, has created a possible use for a whole new group of Portland cement concretes. Concrete can now be produced with unit weights ranging from 30 to 150 pounds per cubic foot and with various insulating, fireproofing, acoustical and structural properties. The tonnage of such materials being used has increased considerably in each of the past ten years, and can be expected to increase for the next several years as availability of the aggregates becomes more widespread and the properties of such concretes become more thoroughly investigated and more generally known. LIGHTWEIGHT aggregates of many types have become avail-able to the construction industry in most localities on this continent

Jan 1, 1963

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961