Search Documents

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By E. O. Lilge

THE USE of the Driessen cone as a heavy-media concentrator involves a mineral dressing process in which many variables inherent in the ore and in the process may have an effect on the efficiency of mineral separation and the operation of the cone. The magnitude of these effects and their possible interrelationships must be known before a full-scale plant can be designed and built. It appears that, among the most important variables, are the following: Ore Variables: The particle size of feed The difference in specific gravity between economic and non-economic minerals The intimacy of mineral association Cone Variables: Cone inlet area Ore to media ratio Cone ratio Size distribution in heavy media Specific gravity of media Viscosity of media Type of media

Jan 1, 1956

By N. Shi, T. G. Joseph

ABSTRACTA series of algorithms were developed to perform geometric and kinematic analyses of cable shovel dipper-ground interactions for a given set of mining face conditions. The routines examine and analyze (a) the position of the dipper in relation to the shovel; (b) the dipper in relation to the face conditions; (c) the dipper position in relation to possible interference or collision with crawler tracks during digging cycles; and (d) kinematic and geometric considerations with respect to any point on the dip-per as it conducts a duty cycle. In all cases, field measurement verifcation provided good agreement(within 4% variance).

Jan 1, 2011

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By Simon B. Blancher, Malo Rousseau, Renato Contessotto, Thomas Wallmach

The Manganese division of the ERAMET group extracts manganese ore in Gabon and produces manganese alloys for the steel industry. ERAMET has an economic interest to maximize the ore throughput without reducing the lifetime of its manganese mines. This can be achieved by means of research and development leading to innovative ore beneficiation processes. For this purpose, the ERAMET research center has designed and constructed a new pilot plant for ore beneficiation by physical separation processes. This pilot facility was erected within an infrastructural and synergetic framework, including competencies in hydrometallurgy, pyrometallurgy, numerical modelling, analyses and mineral characterization that provide ideal research conditions. After laboratory scale tests, a pilot operation of beneficiation of low grade Mn ore (around 35% Mn) was carried out by jigging of the 1-10 mm fraction. This gravity separation process exploits density differences between the various Mn-bearing minerals such as pyrolusite and lithiophorite as well as gangue minerals such as silicates and iron-hydroxides. Enrichment leads to the production of a marketable product associated with a high mass recovery (53% for the jigging step). However, 20% of pyrolusite and 30% of lithiophorite are lost in the waste. Mineral characterization has shown microtextural complexities, but grinding the ore to approach the liberation mesh was not an option due to commercially defined constraints given by the ferro-alloy industry. Recovery of the Mn-bearing minerals or adjustments of the feed grain size (6.3-10 mm) are two potential areas of process improvements identified by means of Qemscan® mineral characterization. This paper details the process tested on a pilot scale (0.5 t/h), which has led to a significant increase in the beneficiation of a low grade Mn ore.

Jan 1, 2016

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By John W. Bell

A FEW years ago the writer had the privilege of examining a piece of apparatus in the Forest Products Laboratory of McGill University which engaged his attention. The Forest Products Laboratory has an excellent installation of wood-grinding machinery, and the officials in charge were naturally interested in acquiring means for estimating the fineness of various wood grinds. The problem was referred to Dr. O. Maass ( l ). Dr. Maass designed a piece of equipment to measure the surface of a wood grind and derived an equation applicable in calculating its value, as follows : After inspecting this apparatus, the writer was disposed to believe that, with some modifications, Dr. Maass' ingenious idea might be utilized to measure the surface of mineral powders. Obviously, some difficulty would be found in maintaining an even suspension of mineral particles of high specific gravity compared to that of wood pulp. The writer will not bore the reader with a description of the various machines built and tried out. Some of these were satisfactory enough to obtain some valuable information, and to bring to light a difficulty which threatened to bring the investigation to an abrupt ending. For the mineral quartz, it was found that Kin the formula above stated was not a constant.

Jan 1, 1944

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012

By T. Crivits

"Phase equilibria in the ‘Cu2O’-‘Fe2O3’-SiO2 system, the base slag system in copper production, were recently determined. However, the addition of MgO, commonly present in the slag, drastically changes the phase equilibria in this system. The present study focuses on the phase equilibria in the ‘Cu2O’-‘Fe2O3’-MgO-SiO2 system in equilibrium with metallic copper.Recently, an experimental procedure has been developed that resolved a number of experimental difficulties. This procedure has been successfully applied to characterise several complex industrial copper slags. It includes a high-temperature equilibration followed by rapid quenching and electron probe X-ray micro-analysis (EPMA). The methodology was adapted to the present system and used to determine the liquidus at SiO2 saturation and in contact with high-MgO phases in between 1100 and 1250 °C in Cu2Orich slags.The results indicate a maximum solubility of MgO in the system at 1200 °C of 5 wt%. The boundary line between tridymite and spinel lies 3-4 wt% closer to the SiO2 apex for every 2 wt% MgO added. These new data on the high-copper slags are important for optimisation of the direct-to blister"

Jan 1, 2014

By D. B. Dreisinger, D. G. Dixon, G. Nazari

"The kinetics of chalcopyrite leaching in acidic ferric/ferrous sulfate media under atmospheric conditions in the presence of pyrite has been investigated. It has been found that pyrite samples from different sources affect the rate of chalcopyrite leaching differently. A strong correlation between the amount of silver associated with the pyrite and its effectiveness has been noted. In this study, improvement of the catalytic properties of pyrite such that all pyrite samples accelerate the rate of copper extraction regardless of their sources is demonstrated, and a detailed discussion of the mechanisms involved in the process of chalcopyrite leaching in the presence of silverenhanced pyrite is presented. INTRODUCTIONIt is well known that chalcopyrite resists leaching in sulfate media. It has been proved that pyrite facilitates the leaching of chalcopyrite (Berry et al., 1978; Dixon et al., 2008; Mehta and Murr, 1983; Muñoz et al., 2008; Nowak et al., 1984, Tshilombo, 2004). Considering the catalytic effects of pyrite on accelerating the kinetics of chalcopyrite leaching, Dixon and Tshilombo (2005) have developed a new process, known as Galvanox™, which has several advantages over other hydrometallurgical processes. Galvanox™ runs under atmospheric conditions, so it requires only low-cost leaching tanks. The sulfur yield at this temperature is high (>95%) which leads to low oxygen consumption and low sulfuric acid generation. The operating temperature is below the melting point of sulfur which eliminates the use of surfactants. This process also does not require fine grinding. Reaction 1 shows the overall leaching reaction in the Galvanox™ process.CuFeS2 + O2 + 2 H2SO4 = CuSO4 + FeSO4 + 2 S0 + 2 H2O (1)Complete copper recovery from the Galvanox™ process can be achieved at a considerably higher rate than other atmospheric ferric sulfate leaching processes (Dixon et al., 2008). Recycling pyrite and recovering copper from tailings with the Galvanox™ process have also been evaluated in continuous pilot leaching campaigns (Dixon et al., 2007)."

Jan 1, 2012

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By J. Palarski

In the Polish coal mining industry, the use of mine waste in underground backfill has been the most common means of providing ground support to minimize surface subsidence, increasing extraction ratios, and reducing the quantity of waste for surface disposal. Over the last decade attention has been focused on the use of different waste as filling material of underground workings and grouting of roof fall rocks in caving area. In the paper, a brief history of the development of fill technology in Polish coal mining industry is presented. Next, the paper discusses various criteria that should be taken under consideration in the preparation process of a fill slurry and grout, fill distribution systems, mining geometry and placement methods. Moreover, in the paper evaluation of the potential of utilizing coarse and fine waste as a resource material in the production of a backfill slurry and grout for filling and injection in abandoned mines is presented.

May 1, 2007

By I. Lazaro Roche, J. Brunner, J. Busto, X. Martin, J. B. Decitre, S. Gaffet, F. Hivert

"Muon tomography allows investigating the subsurface. Muons being penetrative, the attenuation of the muon flux depends on the quantity of matter the particles travel through, hence on the rock density and thickness. For the Temporal Tomography of rock Density using Muon Measurements (T2DM2) project, the muon flux measurements are performed in LSBB URL (http://www.lsbb.eu) in order to study the hydrogeological processes in the unsaturated area of Fontaine-de-Vaucluse karst aquifer. The suitability of the muography for this study is here numerically demonstrated. In parallel to these simulations, muon flux measurements are carried out in the LSBB galleries by means of a set of four scintillator tanks and Micromegas detectors are developed. These detectors, here described, are adapted for underground and confined spaces as well as other environments. Their performances are particularly interesting and should contribute to the expansion of muon tomography in new application fields. INTRODUCTIONMuon tomography or muography is a method to image large volumes by measuring the absorption of cosmic ray muons. It uses, in a passive way, a natural radiation source: the muons which are charged particles produced in the atmosphere. Primary cosmic rays interact with atmospheric nuclei and produce a huge number of secondary particles, including muons. Due to their important mass compared to electrons, they are highly penetrating, reaching several hundreds of meters below the surface. Their attenuation depends on the quantity of matter they cross. That's why they are used to investigate the subsurface, muon absorption measurement allowing to estimate the in-situ density of the rock.Georges (Georges, 1955) proposed in 1955 to use the muons in order to study the density variations caused by the overburden over an Australian tunnel. In 1970, Alvarez (Alvarez, 1970) imaged the internal structure of Chephren Pyramid thanks to this method. The muon tomography has been particularly developed for volcanology (Nagamine, 1995; Tanaka, 2007; Lesparre, 2010; Carloganu, 2013) over the last twenty years. Since the beginning of the 2010's, a growing amount of projects that proposed to use the muons in various fields get underway: the CO2 storage (Kudryavtsev, 2012), the exploration of Mars (Kedar, 2013), etc."

Jan 1, 2015

By M. Kermani

This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill has an alkali activator such as sodium silicate in its materials in addition to primary materials of cemented mine backfill which are deslimed tailings, water and binders. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. Initially, the influence of sodium silicate concentration on the mechanical properties of samples was evaluated using the unconfined compressive strength (UCS) test. Consequently, the effect of curing temperature on CHF and Gelfill samples cured in various curing temperatures ranging from 5?50 °C was studied using the UCS test. Microstructure of selected samples was studied wirth the mercury intrusion porosimetry (MIP) technique. This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Curing temperature strongly influences the mechanical and microstructural properties of CHF and Gelfill samples. (iv) The microstructure analysis revealed that the addition of sodium silicate can modify the pore size distribution and total porosity of Gelfill which can contribute to the better mechanical properties of Gelfill. (v) The MIP tests suggested the microstructure of specimens were changed by adding sodium silicate in a way that the Gelfill samples had a higher percentage of fine pores than CHF samples.

Aug 1, 2013