Search Documents

By Y. -H. Cho, J. -M. Lee, J. -G. Jung

The effects of copper on the microstructure and mechanical properties of ultrasonic melt treated Al-xCu (x=0, 4) alloys were investigated. The densities of alloys were increased and their grain sizes were decreased by UST. The hardness and electrical resistivity measurements revealed that the amount of solute Cu within Al matrix was increased by UST. Both the yield and tensile strengths of Al-4Cu alloy were increased by UST. The improved mechanical properties of Al-4Cu alloy by UST were probably due to the reduced amount of casting defects (e.g. pore), grain refinement, and enhanced solid-solution hardening of Cu.

Jan 1, 2014

By Marcel M. Djivre

The paper will outline the methods and test procedures including the evaluation criteria currently used at the Materials Testing Laboratory (MTL), Sudbury, Ontario, Canada, a laboratory approved by the Ontario Minister of Labour for the purpose of testing or examining mine shaft ropes or other hoisting appliances. Also for Canadian mines the paper will suggest proposed criteria to be used at MTL for the evaluation of ropes used in "ultra-deep" single-lift shafts. Most of the methods and test procedures currently used at MTL were adopted during the revision of the CSA Standard G4, Steel Wire Rope for General Purpose and for Mine Hoisting and Mine Haulage to be published most likely in year 2001. In this latest or sixth edition of CSA Standard G4, a new Clause 14 has been added outlining the requirements for in-service destructive testing of steel wire ropes for mine hoisting applications. The existing fifth edition of CSA Standard CAN/CSA -G4-92, which is intended for the manufacturing of new ropes, includes requirements for raw materials and construction features for round strand and flattened strand rope, and locked coil rope in bright and galvanized finish.

May 1, 2001

By E. Ghali

For engineering applications, magnesium is usually alloyed with one or more elements which include aluminium, manganese, rare earth metals, lithium, zinc, and zirconium. Under normal environmental conditions, the corrosion resistance of magnesium alloys is comparable or better than that of mild steel. The oxide film thickness on pure magnesium after exposure for only ?10 seconds at ambient temperature is 2.2 ± 0.3 nm. Exposure to humid air or to water leads to the formation of a thick hydrated amorphous film that has an oxidation rate less than 0.01 pm/ y. E-pH diagram and high temperature corrosion are discussed. The pH values between 8.5 and 11.5 correspond to a relatively protective oxide or hydroxide film that is more stable at higher pH. Structural applications of magnesium alloys are limited by creep strength rather than by oxidation. Active and active-passive behaviours of magnesium alloys are discussed. The pilling Bedworth Ratio values of oxide and hydroxide are 0.79 and 1.77 respectively and so the formation of Mg(OH)2 inside the oxide film could lead to the development of cracks. Microbiologically influenced corrosion and rational biodegradation of magnesium alloys are discussed because of their interest for medical care.

Jan 1, 2006

By L. P. Chrismas

"IN 1975, Nova Scotia produced 1.8 million tons of coal with a FOB mine value of $47.6 million. Of this total, about 30 per cent or 600,000 tons was coking coal and the remainder was steam and industrial-grade coal. The Nova Scotia Power Corporation consumed 630,000 tons in three generating stations and 570,000 tons were sold to Sydney Steel for making coke for its steel operations. Exports, principally to Great Britain, comprised 370,000 tons in 1975 in addition to the 300,- 000 tons shipped to other provinces for use by cement and pulp and paper companies. In 1975, just over 100,000 tons of coking coal were imported into the province from Alberta. Before 1975, low-volatile coking coal was traditionally obtained from the United States. In 1975, production came from seven individual mines and one project involving reclamation from mine dumps in Pictou County. Of the seven producers, four are owned by the Cape Breton Development Corporation, a federal Crown corporation; the remaining three are small independent mines, but, even though small, they are sizeable contributors to the economies of their local areas. After 101 years of continuous operation, Devco's Princess mine was closed in 1975. The Nova Scotia coal industry, in terms of value, accounted for about half of total mineral production in 1975. The industry provides jobs for 3,000 men and women. It is also significant that in 1975 Nova Scotia produced about 6.5 per cent of Canada's total coal production of 28.3 million tons. Detailed statistics on Nova Scotia's coal industry appear in the Appendix."

Jan 1, 1976

By S. R. Stopic

The EU-financed INTREAT Project (Integrated treatment of industrial wastes to¬wards prevention of regional water resources contamination) addresses the environmental pollution associated with solid and liquid wastes/effluents produced by complex sulphide ore mining and metallurgical activities. The results concerning the electrolytic recovery of cop¬per from effluents formed after mixing of streams from Copper Refining, Precious Metals Plant and Electrolyte Regeneration in the Balkan Area will be shown. The waste water is characterized by low pH values and high contents of heavy metals, such as Cu, Ni, Bi, As, Sb. The majority of these waste water flow untreated into the natural water streams and through the network of existing rivers, which end up in the river Danube. The influence of current density and flow rate on the deposition rate, the quality of copper and the process efficiency will be presented. The full continuous process is based on cells with rotating disc cathodes and represents a pre-treatment step before common neutralisation in a cascade line

Jan 1, 2007

By W. A. D. Edwards

"The Edmonton region accounted for 40% of Alberta's sand and gravel production in 1981 (about 12 million m3). Most of this production was by commercial operations (75%) for use in essential public works projects (64% in road and asphalt production).Although the Alberta Geological Survey delineated 1157 million m3 of gravel, a number of areas are considered to be in short supply. An econometric model was used for forecast demand in the region. Predictions, based on this forecast and estimated supply, are that 15% of the region's gravel and 3% of the sand will be consumed by the year 2010.The City of Edmonton is the largest consumer of aggregate in the region. Approximately 40% of the gravel in Edmonton's current supply area (about 55 km radius) will be used by 2010. These estimates are considered optimistic because the supply figures do not account for sterilization of deposits - some has already taken place in the region. If 25% to 50% of Edmonton's current supplies (one major deposit) were sterilized it would result in $1,000 million of additional cost due to increased haulage alone.Information on the value of aggregate resources, the location of sand and gravel deposit s and forecast demand has been made available to all municipalities in the region to aid planners and regulators in effective future use of this important resource.INTRODUCTIONAlberta is the second largest producer of sand and gravel in Canada at ab out 50 million tonnes annually. Value of provincial production exceeded $120 million in 1985. In Albert a, aggregate is used primarily in road and building construction (about 50% and 15%, respectively) and is important in such activities as petroleum exploration, oil sands development and the forestry industry.The Edmonton region (Fig. I) accounts for about 40% of provincial production and has a per capita consumption rate of about 13.4 m3 of sand and gravel per annum. Although Edmonton dominates, with approximately 50% of regional production going into the city, aggregate is produced in every county and municipal district in the region.Sand and gravel is essential to the current way of life in the Edmonton region. The resource is valuable and dwindling. The Alberta Geological Survey (a department of the Alberta Research Council) has collected information on aggregate in this region for the last decade which ca n aid government planners and regulators in pre venting sterilization and misallocation of this critical resource. This paper is a summary of that information."

Jan 1, 1989

By J. B. Hinzer, J. D. Harvey

"Noranda's Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , ' 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin's (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By Anthony A. Zoobkoff

Gotcha! ? What Did I Just Agree To? ? You can?t repeat or use anything you heard. ? Did you agree before you knew what you were going to be given, told or shown? ? If you knew what you were to be given, told or shown, would you have still agreed?

May 1, 2013

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By Z. F. Zhou, X. Y. Zhou, V. G. Papangelakis, Z. D. Jankovic, S. M. Ulyanov, S. N. Lvov

Recently developed flow-through electrochemical techniques (1,2) were employed for measuring pH in high concentration aqueous solutions and geothermal brines. The pH values of (1) 5.0 mol kg-1 NaCl + x mol kg-1 HCl, (2) 3.0 mol kg-1 of NaCl + 0.5 mol kg -1 of KCl + 1.0 mol kg-1 of CaCl2 + x mol kg-1 HCl (x < 0.1 mol kg-1), and (3) mixtures of Al2(SO4)3-H2SO4-H2O, MgSO4-H2SO4-H2O, and NiSO4-H2SO4-H2O solutions have been measured at temperatures from 100 to 280°C. The obtained experimental data and their thermodynamic analysis demonstrated that the electrochemical system can be used for on-line pH monitoring of high concentration aqueous solutions with an accuracy of ±0.1-0.3 pH units over a wide range of temperatures. Greater deviation exists in real laterite leach solution measurements due to in situ precipitation of Na-alunite. The system is excellent for research and process development work. Further work is needed to ensure robust operation under pressure leach conditions of laterites.

Jan 1, 2004

By W. P. Campbell

In the course of the development of the Red Coulee field, northwest of Coutts, Alberta, a considerable amount of information has been gathered by the Department of the Interior regarding the chemical character of waters encountered in the drilling of wells in this area. The writer, in this paper, has undertaken to assemble the available material with the idea of deducing what relations, if any, may exist between the different waters from the same well, and also how these compare with waters encountered in similar horizons in other wells. From no other district, with which the Department of the Interior has had to do, have there been received so many samples of water, and yet not all the waters logged in the drilling reports were sent in for analysis. The information, therefore, herein contained is not as complete as the writer would have desired, but sufficient evidence has been accumulated to indicate some very definite tendencies in the chemical nature of the waters of this field. The drilling of Red Coulee wells has been carried out exclusively by percussive tools. These permit &apos;dry&apos; drilling, and, consequently, water-sands are recognized when encountered. Had rotary tools been used, information regarding water-sands would have been very meagre, if not entirely lacking, since, in the mudding-off process, water-sands would have been overlooked, with the result that, should water break through into a completed well, its source would not be known and remedial efforts would be greatly handicapped, if not entirely defeated.

Jan 1, 1931

By P. J. Le Roux

"Mining worldwide and definitely in South Africa, is constantly under pressure to reduce its cost structure so as to sustain profitability. In underground gold mines where an open stope mining method is employed, dilution often has a significant effect on the viability of sustaining profits. Target Mine practices Open Stope mining Method and it was found that in some open stopes dilution was in excess of 10%, which has a significant impact on the sustainability of the mine.Dilution in excess of 10% can result in the reduction of the recovered grade from 5,5 to 4,5 grams per ton (g/t). The reduction of 1 g/t in recovered grade results in a potential loss of about ZAR21 Million per month bases on a gold price of ZAR240 000 per kilogram. Based on Life of Mine projections the potential loss of income could be as much as ZAR3,3 Billion. A reduction in dilution would have the opposite effect. There are a number of factors which affect dilution of which falls of ground in open stopes is a major contributor. The falls of ground can be attributed to a number of factors such as beam failure as a result of a larger than normal expected roof area (hydraulic radius too large), poor ground conditions, and poor blasting. The cost of damage to or loss of trackless equipment as a direct result of the falls of ground in open stopes, is very significant. The review of financial figures has indicated that this could be as high as ZAR491 million. This combined with the added cost of transport, hoisting, secondary blasting, milling and plant treatment costs of ZAR293 results in an estimated opportunity loss of ZAR784 million.Currently there is a significant amount of data available in the mining industry which could be effectively used to develop suitable back analysis techniques but to date this has not been used effectively. If dilution can have such an impact on current and future mining ventures then the optimization of back analyses for the prediction of dilution in open stoping could assist significantly in the reduction of dilution in massive open stopes. Rockmass classifications, geotechnical information, blast techniques, blast design, the stress strain environment and hydraulic radius all have an effect on, or play a role in the evaluation of dilution. Each of these factors will be taken into consideration to ultimately determine a measurable or calculated percentage of dilution in massive open stopes.The amount of overbreak in an open stope can be determined by subtracting the planned stope volume in m3 from the actual measured final stope volume in m3, which is obtained from the CMS (cavity monitoring system). This is in turn divided by the planned stope volume in m3 to determine the percentage overbreak. The CMS wireframe is imported into the geological model and its grade re-evaluated. From this the actual percentage dilution for this open stope can be determined. The dilution obtained can result in a major reduction of recovered grade for the open stope, but can also increase the recovered grade. The latter is normally the exception rather than the rule.When analysing data from Target mine the following was achieved:• Using 11 years of data a method of measuring and predicting the percentage dilution in open stoping was developed. This took into account rock mass quality, stress-strain state, and the hangingwall hydraulic radius (size of stope hangingwall exposed).• Implementation of this prediction method resulted in a reduction in falls of ground in open stopes. The benefit of this was a reduction in the damage to mechanised equipment resulting from less falls of ground which had a positive effect on the profit margins of the mine. As a direct result the recovered grade from the open stopes increased due to the reduction in the amount of dilution.• A design criterion, Dilution Stress-Strain Index (DSSI), was developed which allows the user to calculate, with certainty, the stability of the open stope and determine if m"

Jan 1, 2015

By H. Yoshida, H. Hatta, T. Suzuki

"The effect of the copper and magnesium contents and quenching rate during quenching on the age hardening behavior of 2000 series aluminum alloys was investigated. For the higher copper-containing specimens as conventional alloys, like AA2024, precipitation of the stable phases increased as the quenching rate decreased under the as-quenched conditions. The maximum hardness after the artificial aging of air cooled(AC) specimens was much lower than that of the water quenched(WQ)specimens. On the other hand, for the lower copper-containing specimens, coarse precipitation did not increase even in the case of the AC. The age hardening behaviors of the WQ and AC were very similar such that the maximum hardness and aging rate were almost the same. Many parts of the fine precipitates that increased the hardness were thought to be the GPB zone or fine S’ phase for the WQ and relatively coarse S’ phase for the AC. From the calculated CCT(continuous cooling transformation)diagrams, the lower copper-containing specimens could maintain the copper and magnesium in the solid solution state during the AC, so they could be quenched at a rather slower quenching rate like the AC.INTRODUCTIONThe 2000 series aluminum alloys, containing copper and magnesium as the major chemical components, are some of the well-known heat treatable aluminum alloys. These alloys have a high quenching sensitivity, thus the age hardening ability of these alloys decreases with as low quenching rate. To prevent the decrease of the age hardening ability, quenching is done by a method such as water quenching, which is not very efficient in an industrial situation, because the method requires such large equipment. For these alloys, reducing the quenching sensitivity helps them to be produced in a rather convenient way. For example, 6000 series alloys such as A6063 have low quenching sensitivity, thus they could be quenched by only air cooling just after extrusion and they do not need water quenching. Based on these reasons, investigations of these alloys with high copper and magnesium contents have been conducted in the past to find a way to lower the quenching sensitivity by adding transition elements such as manganese, chromium and zirconium (Kanno, Suzuki, & Itoh, 1986; Suzuki & Itoh, 1986; Kanno, Sakuma, Muromachi, & Watanabe, 1988). However, very few studies have focused on the quenching sensitivity of the lower copper and magnesium containing alloys because of their usage for structural components with high strength, and most of the past studies have used only the fast quenching method like water quenching. On the other hand, from our recent results, there is a possibility to lower the quenching sensitivity of 2000 series alloys with lower alloying elements. In this paper, the effect of the copper and magnesium contents with lower alloying elements and quenching rate, especially in case of slower quenching rate than conventional quenching method, on the age hardening behavior of the 2000 series alloys is investigated by the hardness measurement, structure observation and thermal analysis."

Jan 1, 2018

By J. P. Jylhä, A. Jokilaakso

The Outotec Flash Smelting process is widely used in primary copper production. A layer of slag on top of matte (copper–iron sulphide melt) creates a barrier through which matte droplets descend. Droplets of different sizes settle through the layer at different rates, which increases possibility of copper losses as smaller matte droplets may be removed with the slag. In this work CFD-DEM (computational fluid dynamics – discrete element method) coupling was used to simulate matte droplets settling through the slag during slag tapping. Discrete droplets and slag flow were simulated with DEM and CFD, respectively. This new approach enables tracking and solving movement and interactions of individual droplets. User-defined models were created to take coalescence and reaction kinetics into account. Coalescence created larger droplets, while the reactions decreased droplet size and increased its density. Drag caused funnelling effect, which pulled droplets towards the centre line of the descending cluster. This research is the only study known by the present authors in modelling liquid-liquid systems with the CFD-DEM coupling. Simulating coalescence and chemical reactions for discrete droplets enables more realistic simulations. However, CFD- DEM simulations are computationally resource intensive already without additional models, so a full scale industrial settler modelling still waits for further increase in computer performance. INTRODUCTION Flash smelting is a method used in copper and nickel production. In the flash smelting process, oxidation of sulphides in a concentrate is used to release energy needed to smelt the feed. In the process, copper matte is formed. Matte has copper content in the range of 55 – 70% (Sridhar, Toguri, & Simeonov, 1997), the rest is mainly sulphur and iron but has still many other impurities (Taskinen, Seppälä, Laulumaa, & Poijärvi, 2001). Oxidized iron forms iron-silicate slag while SO2 is collected for acid production (Davenport & Partelpoeg, 2015). The Outotec flash smelting furnace (FSF) can be divided in four major component: concentrate burner, reaction shaft, settler and uptake. Concentrate, flux and oxygen enriched air are injected into the reactor through the concentrate burner. The mixture then reacts in the reaction shaft forming matte and slag, which are collected in the settler, while off-gases flow out of the reactor through uptake for heat and dust recovery, and SO2 collection for H2SO4 production. The matte and slag form separate layers due to immiscibility and density difference. Raw material feed is continuous, but the matte and the slag are tapped periodically. A flash smelting furnace is depicted in Figure 1.

Jan 1, 2019

By Pierre Antoine Dhaiti, Gilbert Sergerie, Michel Dagbert, Jean-Maurice Brodeur

"Quality of iron ore is generally determined by several factors which can be correlated or independent. Among these f actors, we generally find per cent iron, silica, magnetite or hardness. Forecasting the short- and long-term fluctuations of these f actors in the future pit is an important feature of mine planning in these deposits. Computer simulation provides a realistic answer to these questions. It allows to generate values for the most important quality features of each shovel load with the proper correlations between them as well as between one load and the next being fully reproduced. Then different sampling schemes f or grade control or blending facilities can be examined on the simulated data. The mechanics of the simulation procedure and its potential applications are described in an example.IntroductionThe purpose of this paper is to illustrate the use of in-situ grade simulation in the planning o f the grade control in an iron ore min e. More precisely, given a production unit of given size, we need to know how many samples have to be collected in that unit so that we ca n recognize its grade with a reasonable precision. Conclusions that we would like to arrive at are of the type: with 4 blasthole samples we ca n get the iron grade of a 10,000 ton bloc k with less than a ± 2% Fe error 95% of the time.The approach t hat we take to solve this problem is simulation. We simulate the grade of samples and the grade of the block that contains these samples. We repeat the simulation for hundred s o f blocks. By comparing the sample grade with the block grade in each case, we determine the actual number o f blocks where the difference sample-bloc k is less than a given limit."

Jan 1, 1983

By Dharmendr Kumar, Pradip, Sivakumar Subramanian, Beena Rai, Venugopal Tammishetti

The separation efficiency in a mineral processing plant is generally assessed and reported in terms of elemental assays constituting the minerals of interest. However, different minerals comprising of same elements behave differently under similar process conditions. Thus, it is imperative to track the mineral composition thank elemental composition of different streams in a processing plant. The availability of automated mineral analyzers such as QEMSCAN and TESCAN in recent times has made it possible. However, due to the high cost and expertise required, their adaptation in day to day monitoring of operations is not yet a common place. X-ray diffraction (XRD) profile fitting (Rietveld Refinement) is another technique which can provide estimates of mineral proportions in a sample. The results of Rietveld Refinement however are affected by coating of fines on coarse particles, method of sample preparation, particle size distribution of sample, elemental substitution in mineral crystal lattice. In the present work, we propose a simple and efficient method for quantitative estimation of minerals in iron ores using elemental assays and thermo-gravimetry analysis data. The minerals (hematite, goethite, gibbsite, kaolin and quartz) are identified using powder XRD analysis. It is also observed that goethite contains Al substitution in the crystal lattice. The samples were analyzed for %Fe, %Al2O3 and %Silica using chemical analysis. The measured Loss on Ignition (LOI) in the sample is contributed from goethite, gibbsite and kaolinite phases. LOI from gibbsite and goethite occur in temperature range 250–350°C and LOI from kaolinite occur in temperature range 400–700°C. According, LOI are determined in two different temperature ranges that are 100–400°C and 400–850°C. We have used the data to successfully determine the mineral compositions of iron ore samples. We have also employed a data reconciliation algorithm on the calculated data for further improvement and consistency of our results. Our method is very convenient for quick estimation of mineral proportions in a sample. The proposed method can also be used for quantitative phase estimation in bauxite ores and red muds.

Jan 1, 2016

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90&apos;s to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he&apos;s hurt. Maybe he&apos;s not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

Oct 1, 2010

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By R. W. Lawrence, A. Bruynesteyn

"Pre-oxidation of refractory pyritic concentrates by biological leaching to enhance the recovery of gold and silver in cyan ideation has been investigated. The results of laboratory tests on three concentrates are presented. In all cases substantial increases in precious metal recoveries were obtained following the pre-treatment. For one concentrate, gold recovery of 81% was achieved following an 87% oxidation of pyrite, compared with 24% recovery by direct cyanidation of non-oxidized concentrate. Gold and silver recoveries from the other concentrates were increased from the range 60-78% to over 90% and from 80-86% to over 98% respectively. Operating parameters are discussed and methods of maintaining high oxidation rates are evaluated. Methods of employing this pre-oxidation technique in commercial practice are described.IntroductionMany of the gold and silver deposits now being developed contain precious metals finely disseminated in sulphide minerals such as pyrite. These ore s often present considerable resistance to metal recovery. The ease with which gold may be extracted is usually related to grain size and its manner of distribution within the host mineral. In many cases, a significant percentage of the gold may occur in submicroscopic form, or in solid solution with pyrite, so that even very fine grinding fail s to liberate the metal for recovery by cyanide leaching. Such ores are often termed refractory. Even in cases where liberation by fine grinding is practicable, high cyanide and lime consumption may be experienced due to the presence of specific sulphide minerals, and poor metal recovery may result.Pre-oxidation methods for refractory ore s and concentrates are commonly used to improve precious metal recoveries. Roasting, for example, as a pre-treatment to cyanidation, removes harmful constituents by oxidation or volatilization, and liberates gold from pyrite. In some cases, however, this method of pre-oxidation can result in poorer metal recovery, particularly of silver, due to fusion and the formation of clinker, and the formation of compounds which consume cyanide in the subsequent metal recovery stage. Difficulties in compliance with environmental pollution regulations may also be encountered."

Jan 1, 1983