Search Documents

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By L. T. Loe, A. S. Norsk, Mo i. Rana

High production rate and good stability demand the optimization of all phases of electric pig iron smelting. This is important with respect to slag chemistry, which to a large extent regulates the process temperature in electric smelting. Controlled basicity and slag volume. and a satisfactory screen analysis of the reduction material and sinter, are of the utmost importance for smooth furnace operation. Large variations in slag volume and in B/ A and C/Fe ratio will have an influence on the furnace resistance and thus the specific energy development in the furnace, which lead to variable reduction of SiO.. The result will be variable hot -metal quality and un-stable furnace operation.

Jan 1, 1970

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By Y. F. Jiang, K. Fang, Q. Q. Jiang, Q. Wu

Inter formational sliding of bedding planes between two different rock types in Badong formation is an important reason that leads to the instability and fracture of rock mass in this stratum. There are no specific research achievements on bedding planes between two different rock types in Badong formation. In order to study the shear mechanical properties of bedding planes between two different rock types. This paper using the software of particle flow code (PFC) and JRC model to establish several typical structures of different roughness coefficient of surface morphology based on the laboratory tests on silty mudstone and marlite in Badong formation. A great deal of numerical shear tests were carried out by ball production, radius expansion and servo infliction. The research results are as follows: First, shear strength of Badong formation is found to vary between that of silty mudstone and marlite isotropic planes by analyzing shear strength of the homogenous bedding planes and inhomogeneous rock types, we can find that the shearing strength in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the shearing strength of silty mudstone isotropic planes. Second, the basical friction angle of bedding planes between two different rock types in Badong formation is between silty mudstone and marlite isotropic planes and which is closer to the basical friction angle of silty mudstone between isotropic planes. Third, based on the experimental results, an expression is obtained to describe the relationship of the ratio of shearing strength between bedding planes of two different rock types and isotropic planes in soft rock, the rock combination coefficient, and the roughness coefficient. This study has important significance for further research on the shear mechanical properties of bedding planes between two different rock types.

Jan 1, 2015

By G. Scott Zimmer

Mine planning at Cassiar consists of an annual cycle of projection, control, evaluation and revision following completion of annual diamond drilling during the summer months . The inherent difficulty in evaluating fibre grade and distribution, combined with a high-wall phase or push-back mining system, requires continuous modification to designs and schedules based on a cumulative evaluation of equipment performance and prediction versus production. To expedite the planning sequence, a mini-computer system has been introduced which allows emphasis to be placed on optimizing designs, exempting personnel from manual calculations and tabulations.

Jan 1, 1978

By Jehan Rondot

Les bancs de quartzite inhabituellement purs et epais decouverts lors de la cartographie geologique de la region de Charlevoix sont maintenant entres au stade de !'exploitation et se revelent etre une richesse naturelle durable pour cette region. Les etudes stratigraphiques effectuees dans cette partie (Quebecia) du bouclier canadien indiquent que la succession: lo. complexe a amphibolite et leptynite a la base, 2o. quartzite et gneiss a sillimanite, muscovite et gneiss calcosilicate et conglomeratique au sommet est constante sur de grandes distances (de Charlevoix a la Basse Cote Nord) et represente une sedimentation continentale et de plateforme, peu epaisse, du proterozotque inferieur. La purete et la grande epaisseur du quartzite s'expliqueraient par un processus de sedimentation continentale complexe ou se succedent climat tropical-humide et glaciaire-aride et transport fluviatile et eolien. Parmi la multitude de depots de quartzite qui existent dans le monde, peu sont de qualite superieure. Or, de par sa composition chimique, le quartzite de La Galette se compare avantageusement a ceux des meilleurs gisements des Etats-U ni s, de l'Europe de l'Ouest et de I' Afrique du Sud. D'acces facile pour l'exploitation, les gisements ne sont qu'a une quarantaine de kilometres de Baie Saint-Paul ou de La Malbaie, sur le SaintLaurent. L'utilisation en metallurgie du quartzite de La Galette comprend la production de silicium, de ferro-silicium et d'autres alliages de silicium . La composition du quartzite est en outre appropriee pour la production de carbure de silicium et de silicate de sodium. Les fines peuvent etre utilisees pour la fabrication du verre et comme matiere de charge.

Jan 1, 1984

By L. Chunpongtong

One of the challenges of mine planning is to determine the most cost-effective replacement time for aging equipment. The lifespan of equipment, such as haul trucks and shovels, deployed in mining operations varies due to the nature of the material and ground conditions in which it operates. For engineering economists dealing with aging equipment, the options become an economic trade-off between higher maintenance cost versus the cost of new equipment. The discount rate plays a significant role in this decision; the higher the rate, the longer the economically optimal lifespan. Therefore, the ultimate question is: ?How can the relationship between the discount rate and the economically optimal lifespan be expressed mathematically??

Aug 1, 2013

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By F. H. Wheeler

CONSIDERING the nature of this audience, I perhaps, in addressing you on the subject of air transportation as related to the mining industry, should speak with tongue in check or at least with some reservation. I know full well that many of you, veterans in the great mineral development in Canada, are perhaps more conversant with the overall aviation picture than I, for aviation to you has been the means to an end, and in many instances has been part and ?parcel in the success of your particular projects, in the form of the initial means of transport. I feel, however, that we in this room today have somewhat parallel geographic interests - yours in relation to what is in the ground, mine in the air - and also in the forests and in the streams - aviation, hunting, and fishing - things which have occupied my attention practically all my adult years. In the light of what has gone. before, and in view of present developments, I think you will agree with me when I say that I do not think there could be a more intriguing pursuit than playing a hand in rolling back Canada's tremendous northern frontiers, even if, at this stage, we have made but slight impression on the untold opportunities which lie in our wide-spread, undeveloped areas.

Jan 1, 1956

By Michael Harley, E. Guy Charleworth

"Bedding-parallel thrust-hosted gold veins are developed in the Sabie-Pilgrim's Rest goldfield, eastern Transvaal, South Africa. The reefs display a complex history characterized by temporally and spatially overlapping events of similar mineralization and deformation. Recognition of the episodic reactivation of these low angle (5° to 10°) thrust faults implicates high fluid pressures (equalling or exceeding lithostatic pressures). Geochemical constraints limit the amount of fluid-rock interaction and the occurrence of transgressive mineralization within the Archaean granitoid basement suggests that the high pressure fluids originated at depth beneath the Transvaal Basin.Similarities exist between gold deposits of Sabie-Pilgrim's Rest and Telfer, Western Australia as well as Passagem de Mariana, Minas Gerais, Brazil. All deposits are sub-parallel to the enclosing bedding which is shallowly inclined. Furthermore, they are also hosted by contractional deformational structures and are clearly epigenetic in origin."

Jan 1, 1994

By Isabel C. B Rodrigues, Flávia D. Reis, Versiane A. Leão, Rosa M. F. Lima

Attention has been focused in recent decades upon the precipitation of metal sulphides from acid mine drainage (AMD) and pregnant leach solutions, due to the advantages of the sulphide precipitation process over traditional methods employing hydroxides. The aim of this work was thus to explore technologies for copper precipitation using either Na2S or biogenic sulphide. The recovery of copper sulphide was improved when the initial pH of the solution containing each metal was 4 or excess sulphide was employed. In such, a condition the removal efficiency was 99.9%, corresponding to a residual level of 0.1mg/L for copper in solution. Kinetic parameters for precipitation were determined from the particle size distributions using the method of moments, where the growth and nucleation rates, as well the agglomeration kernel, were calculated. The biogenic sulphide was a suitable alternative to sodium sulphide for copper removal as either sodium sulphide and biogenic sulphide can be utilized to precipitate such a metal allowing the effluent to be compliant with environmental legislation.

Jan 1, 2014

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940