Search Documents

By Carter LC

Following the perception by the Groote Eylandt Mining Company of a need to further beneficiate a fines product, and preliminary metallurgical testing to demonstrate the feasibility of such beneficiation, a comparison was made of the various configurations of cyclonic heavy medium separators available. This comparison consisted of (i) a pilot plant test in which a dynawhirlpool (DWP) and a pump fed cyclone were compared, and (ii) a survey of operating plants using the systems under consideration. Little metallurgical difference was found-between the different systems. The gravity fed cyclone configuration was finally chosen based on a particular need to minimise degradation of ore and on a desire, in so isolated a location, to use established and locally supported technology.

Jan 1, 1987

In recent years a large number of Horizontal Belt Filters have been installed in the Australian mining and chemical industries. This paper deals briefly with the general background and advantages leading to the selection of this type of filter. Several different applications are described and particular reference is given to the simplification of the fines treatment circuit at the South Bulli Coal Washery.

Jan 1, 1989

By Harris RW

Acoustic Emission structural integrity evaluation tests rely on the validity of the detected acoustic emission data and the ability of the practitioner to both analyse and interpret the data to make a correct decision on the future use of the structure tested. Unfortunately with acoustic emission surveillance testing, it is not possible to know that all the available data has been assessed property. The equipment sensitivity, threshold settings, and event capture capacity, when combined with the decision making ability of the operator in real time, make it very difficult to achieve reliable integrity evaluation. The main problem is to interpret the data and so any monitoring system should involve expert systems in conjunction with both acoustic emission and other operational monitoring data to maximise the utilisation of the large amounts of information now available from operating plants, mines and structures.

Jan 1, 1991

By N R. Johnson

The overland conveyor at the Los Pelambres mine in Chile is designed to move 8700 t/h of material over 12 km at a speed of 6 m/s while descending 1400 m. The conveyor, which is divided into three segments, is equipped with a braking system that must bring it to rest without producing excessive stresses in the conveyor belt. Retardation and gently stopping a mass of 250 t requires retardation times in the order of 60 seconds. Brakes that can provide this performance require sophisticated controls as well as very high heat absorption capacity. This paper describes the thermal analysis of the braking system, which required the use of novel materials to meet the arduous duties imposed on the callipers and discs.

Jan 1, 2005

Australis Mining N.L. operates a continuous mode carbon-in-pulp (CIP) gold plant, processing sand and slime tailings from previous gold mining operations in the Norseman area. Plant design is that of conventional countercurrent contact between pregnant pulp and activated carbon. Gold desorption is achieved by the Zadra process using near boiling tempera- tures and atmospheric pressure. Process water is drawn from nearby Lake Cowan (saline). The plant operates at, or above, design specification of 400 dry tonnes per day. This paper describes the plant design and operating processes utilised in optimising throughput and gold recovery. TNTDnPTTnmTnM Favourable world gold prices and substantial reserves of sand and slime tailings prompted Australis Mining N.L. to construct a gold extraction plant during 1981. The projected plant throughput was set so as to complete treatment of available tailings over a three year period. Metal- lurgical tests indicated that, with a regrind facility satisfactory gold recovery could be achieved using a countercurrent CIP process. Reflecting the entry of Australis Mining N.L. into its first large scale treatment operation, the plant design emphasised simplicity but effectiveness of Operation.

Jan 1, 1982

By Fitter JF

Drilling and blasting practices at Groote Eylandt are undergoing a period of rapid change. Practices over the last ten years are reviewed and some specific blasting problems currently being faced are described. A move from percussion to rotary drilling is outlined, together with the reasoning behind a proposed return to ANFO from watergel explosives. A brief outline of the various firing patterns used is given, together with a description of the drilling and blasting recording procedures currently in use. Current and planned developments in drilling and blasting at Groote Eylandt are also outlined, emphasizing the success of wide patterns, fired in line with long inter-row delays.

Jan 1, 1982

Detailed studies of mineral paragenesis, isotope and trace-element geochemistry, and physical mineralogy at Mount Morgan are compatible with deductions by Geopeko Ltd geologists concerning field relationships in the mine area. Considered together, field and laboratory data suggest that the Mount Morgan deposit originated from a shallow, intrusive, acid volcanic dome similar to those which produced the Kuroko-type deposits in Japan. At Mount Morgan, however, interaction with sea water was much less, the sulphides were concentrated rather than forming a group of deposits, and only the throat of a breccia vent is pre- served, so that only the lowermost parts of Kuroko-type deposits can be compared with the Mount Morgan mine. A final difference lies in the presence at Mount Morgan of a quartz diorite adjacent to the ore. Mineralogical data are compatible with post-ore intrusion, possibly up an earlier volcanic fissure.

Jan 1, 1974

The epizonal Ag-Pb-Zn vein deposit at San Bartolome is characterised by a base-metal sulphide assemblage containing the spectacular development of interpenetrating, bladed networks of pyrrhotite which have been replaced by marcasite and pyrite. A similar assemblage displaying the same crystal habits and textures are also a diagnostic feature of the Sn and Sn- Ag deposits of Bolivia. On this basis, it is reasonable to conclude that both deposits were formed from fluids of similar nature and origin. Although no economic accumulation of Sn is known in San Bartolomr, further comparison of the geologic setting, age, mineralogy, fluid inclusion data and magmatic association of this deposit with the Bolivian systems has highlighted additional similarities consistent with a hypothesis that more extensive Sn mineralisation might exist in the San Bartolomd area.

Jan 1, 1995

By D R. Swinbourne, Y H. Yang

Calcium ferrite slag has gained prominence in the copper smelting industry over the last decade due to the emergence of continuous converting as an established technology. As smelters move towards processing which is higher in intensity, more efficient and more environmentally acceptable, its use is likely to increase because it has technical advantages over conventional iron silicate slag, which include a higher magnetite-holding capacity, lower copper losses to slag and a lower viscosity. Calcium ferrite is currently the converting slag of choice in the Mitsubishi process at operations in Japan, South Korea, Indonesia, Canada and Australia, and in the Kennecott/Outokumpu flash converting process in USA. However, users of this slag have experienced problems in containment due to its highly corrosive nature and low viscosity. As use of this slag becomes more widespread the containment problem will assume greater importance. Consequently, work has recently been carried out to establish the mechanism of refractory attack and devise means to retard it. This work will be critically reviewed in this paper.

Jan 1, 2000

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Kaji S

The Tsugaru Tunnel, located on the Honshu island approach to the Seikan Tunnel, is 5,880 m long and has a "Shinkansen" cross section of 90 m2 area. The geological formation through which the tunnel passes consists of very soft rock most of which is unsolidified sandstone belonging to the Neogen. The permeability coefficient is in the range of 10-2 to 10-4 cm/s and being water bearing with a high ground water level, the ground is unstable and subject to soil outflow phenomenon. Kajima Corporation, undertaking the Futamata Construction Section (1,420 m long), excavated the tunnel by the upper half heading method with side pilots employing the following countermeasures to cope with these severe conditions.

Jan 1, 1987

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

By Turner T. M

The problem of metering fine particulate material at low flowrate is often encountered in metallurgical experiment. This note describes a feeder which wa developed to provide metered flows of copper sulphide concentrate in the range of 0'1-0'7 g/min.It is believed that the present device is easier to operate than previously described feeders (e.g. Hamor and Smith, 1971). It may have applications in the field of analytical chemistry, as well as in metallurgical investigations.

Jan 1, 1978

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

The Kidston Gold Mine i s located in northern Queensland some 2 Ukm northwest of Townsville. I t is the largest gold mine in Australia and produces approximately 25 percent of Australia's gold and one percent of the world's gold.Initially, traditional mining industry management approaches resulted in the rejection of what appeared to be an attractive low-grade deposit as an uneconomic proposition. Critical re-examination revealed that the rejection was based upon managerial inflexibility and traditionally over-conservative methods of mine evaluation, construction, operation, projected commodity prices and contingency factors. "Ihus it tradition was to prevail, the Kidston prospect would never have been realised.

Jan 1, 1985

By Das A. K

Investigations were carried out to understand the effect of liquid viscosity (u = 1 x 10-3 - 5 x 10-' Ns/m2) on the size of primary bubbles formed at high gas injection rates (Q = 100 - 1000 cc/s, U = 0.04 - 0.42 mach) under room temperature conditions using flush tuyere (3 mm diameter) operating vertically upward. Tuyere pressure fluctuations were correlated to the mode of bubble formation by simultaneously filming the bubble and the corresponding tuyere pressure fluctuations displayed on an oscilloscope screen. A simple mathematical treatment is presented to estimate bubble size in viscous liquids. The theoretical results are compared with the experimental measurements.

Jan 1, 1987

By A Hewitt

Portland cement is the chief binding ingredient in mine backfill. In the presence of water, the chemical compounds within portland cement hydrate causing hardening and strength gain. During hydration, heat is generated. In certain cases, hydration heat may be produced significantly faster than it can be dissipated, which can create high temperatures in the underground environment. This paper presents the results of a series of investigations aimed at quantifying the heat generated by cemented backfill during hydration. Scaled stope models, instrumented with thermistors, were used in the investigation. Heat transfer to the hanging wall, orebody, footwall and cross-cut and production drifts was assessed during the backfill curing process and relationships between cement content, cure time, and heat generation were developed. The results of this work will assist mine operators in predicting the heat generated by cemented backfill and provide the necessary information to implement effective engineering control of heat in the underground environment.

Jan 1, 2005

Copper heap leaching involves both the simultaneous and sequential leaching of very large tonnages of ore over long periods of time. It is not unusual to be leaching three or four million tonnes over periods of 12 to 18 months. As a consequenc

Jan 1, 1998

By Fleming GJ

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within the Andaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra.

Jan 1, 1995