Search Documents

Traditional methods for monitoring, and hence controlling, pyrometallurgical processes rely heavily upon the skill and experience of operators. A skilled operator will usually achieve consistent, though often conservative, results, whilst an un-skilled operator will require considerable time and training to achieve the same results. Semtech Metallurgy AB have demonstrated that continuous and precise control of pyrometallurgical processes can be achieved through on-line analysis of pyrometallurgical flame off-gas using optical spectroscopy. The feasibility of the technology has been demonstrated on a large number of full-scale tests at production plants and by several commercial installations. Evidence suggests that installation of this technology, called Semtech Optical Production Control (OPC), has resulted in considerable economic benefits to the plant efficiency and asset life. These economic benefits are believed to be a direct result of improved objective on-line control. Technically the following benefits have been demonstrated: improved metal grade control, reduced metal losses, reduced processing time, and improved personnel safety. SemtechÆs OPC is a non-intrusive technology which relies on the fact that the composition of the vapour phase above a high temperature melt is closely related to the instantaneous status of the melt. This enables on-line real-time analysis of the furnace melt to accurately determine melt status and in particular reaction endpoints. Originally developed for on-line monitoring of copper converting in a Pierce-Smith vessel the field of applications for the technology is steadily growing. This paper introduces the Semtech OPC technology; discusses various applications and outlines the demonstrated benefits.

Jan 1, 2002

The Olympic Dam deposit is located some 600 km north of Adelaide in South Australia. It was discovered in 1975 by Western Mining Corporation and in 1979 a joint venture was formed with British Petroleum for the evaluation and development of the project. Studies were completed and construction started in 1986 with the plant being commissioned progressively between April and August of 1988. In 1993 Western Mining acquired BP's interest and are now owners of the whole deposit. The scale of the initial development was 1.5 Mtpa of ore for the production of 45 000 tpa of copper cathode, 900 tpa of uranium oxide and some gold and silver. Two expansion programs have occurred in 1992 and 1995 and current performance is at the rate of 3 Mtpa of ore for the production of 84 000 tpa of copper cathode, 1500 tpa of uranium oxide, 24 000 oz per year of confined gold and 380 000 oz per year of confined silver (Table 1). An aerial view of the plant is shown in Figure 1. The benefit of diversifying into the production of more than one product is undoubted and the flexibility of being able to produce variable quantities of copper and uranium also allows advantage to be taken of a change in market conditions.

Jan 1, 1996

By M J. Pascoe

The performance of 460 stope surfaces at WMC ResourcesÆ Olympic Dam Operation (ODO) has been used to investigate the confidence that can be placed in the Stability Graph Method for design of stope dimensions. A detailed database of stope performance and ground condition information was established for each stope. The database contains all the required stability graph information as well as other factors thought to influence stability, such as discrete major structures, poor shape and exposure time. The performance of each stope surface was quantified by calculating Equivalent Linear Overbreak/Slough (ELOS). The performance of stope walls and crowns was plotted on the supported and unsupported case history stability graphs. Based on this information an ODO design limit of HR = 3.3 x NÆ0.33 has been suggested for stope walls. Walls that plotted above this line were 80 per cent stable, 20 per cent unstable and zero per cent failed. Below the line 60 per cent were stable, 30 per cent unstable and ten per cent failed. Supported crowns that are flat or arched in shape and are not within the influence of major structures can be designed in the stability graphÆs æstable zoneÆ with a strong likelihood of stability. The Stability Graph Method did not reliably predict the performance of unsupported crowns at ODO.

Jan 1, 2005

By Cripps-Clark CJ, Deague TK

In order to study conditions under which SiO(g) may be formed in a blast furnace, equilibrium phase diagrams were constructed for the combustion of high and low ash cokes with oxygen-enriched blast and oil injection under conditions of high and low raceway pressures. Free energy minimisation techniques were used to calculate the composition of gaseous and condensed phases. Where coke ash is assumed, for simplicity, to comprise Si02 only, the coke can be comple- tely gasified, mainly to SiO and CO, under restricted conditions of coke to blast ratio and at temperatures greater than 1600 - 1650¦C, depending on system pressure. The formation of SiO(g) is partially suppressed by the introduction of alumina into the ash, because of the formation of solid and liquid alumino- silicate compounds. The minimum temperature for complete silicon gasification is raised to about 1700¦C. The results of the equilibrium calcula- tions are related-to actual raceway conditions. It is proposed that virtually all silicon in the coke ash is gasified such that, on condensation, it affects hot metal chemistry and slag properties and secondly, that the effects will be greater with higher ash cokes.

Jan 1, 1980

Blasting is known to be both an important and an easily quantified cost factor in rock breaking operations. However, the indirect costs and benefits of the blasting operation are not easily determined due to the irreversibility of the mechanisms involved and the multiplicity of influencing factors. A general conceptual model showing the relationship between blasting and mining costs is well known, but serious attempts to address the critical real relationships have all floundered on the fact that not enough is yet known about either detonation physics or blasting effects. This can only be remedied to the extent that blasting instrumentation enables researchers to pin down not only the relationship between the detonation process and its impact on a particular environment, but also the downhill costs of handling the rock, repairing any damage and building in "Safety Factors" to provide for imponderables. It is vital to standaraize on specifications for instrumentation and measurement techniques and there is a need to review what has been achieved in blasting expertise so as to focus on the most fruitful paths for future work.

Jan 1, 1990

Downstream value-adding is a strategic issue for a country like Australia, which has a resources-driven sector of a scale that has significant impact on the national economy. The question of why producers are not doing more to ævalue-addÆ is often asked. In Australia this debate takes place within the context of: an era of unprecedented growth in demand for resources driven by the rapid urbanisation of China, India and others;impending legislation and uncertainty around carbon pricing;rapidly rising energy costs;significant supply-side shortages including infrastructure, skills and manufacturing capacity; andsignificant industry consolidation of primary resource producers with commensurate improvements in market power.There are several examples of resource-based industries which have developed their business along the complete value-chain; for example large oil and gas producers successfully span upstream and downstream operations including refining and petro-chemicals as well as retail distribution of fuel and other products. Relevant frameworks that provide insight and understanding into the strategic issues around value-adding are reviewed and examples of the application of these frameworks to companies and industries which have successfully adopted a strategy of integrating along the value-chain, as well as those players who have focused on parts of the value-chain are presented. The issues around value-adding in Australia are then reviewed with reference to these frameworks and it is concluded that the issue is a conflict between the objective companies who wish to maximise financial value versus the desire of governments to increase economic benefits. An approach to aligning these objectives is proposed.

Jan 1, 2008

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

By Fisher WJ

The'treatment of the South Alligator valley uranium ores passed through three phases dictated by economic circumstances during the years 1956- 640 In the first phase high grade ores were treated by hand sorting and wet gravity separation for recovery of high grade concentrate to meet a United States Atomic Energy Commission (U.S.A.E.C.) contract for plus 50 per cent pitchblende concentrates. Secondly tailings from the gravity plant and some high grade ores were trucked to Rum Jungle and sold to the Australian Atomic Energy Comm- ission (A.A.E.C.). Thirdly solvent extraction plants were built at Moline (previously Northern Hercules) by United Uranium N.L. (UOU.N.L.) and at the South Alligator River by South Alligator Uranium N.L. (SOA.U.N.L.). These were the first solvent extraction plants designed in Australia, as earlier plants used the ion exchange process for recovery of uranium oxide. The plants were small, indeed the S.A.U.N.L. 15 ton per day plant was possibly the smallest commercial plant known, but they operated efficiently with good recoveries, and were placed on a care and maintenance'òbasis when contracts were filled. Sulphuric acid was supplied in bulk to both plants by the A.A.E.C. from the 30 ton a day acid plant at Rum Jungle. Gold was recovered as a by product of uranium ore from the Moline plant.

Jan 1, 1968

The first introduction of automatic control systems for flotation occurred about fifteen years ago. The early control work coincided with the introduction of on-line assaying using XRF techniques. This OSA availability, coupled with the emergence of small digital computers suitable for process control in the late 1960-s, meant that the necessary process information and control hardware existed for flotation control experiments. A period of intensive research related to flotation control. ensued. A great deal of effort was devoted to the development of mathematical models of flotation. Plant experimentation sought to understand the effects of a range of flotation variables on the process. Finally, control loops were proposed and plant tested. An evolutionary pattern emerges when the range of flotation control installations is examined. The earliest systems had as objectives process stabilisation using reagent control. There were also some early attempts at flotation optimisation procedures, again using reagent variation. Current work is still associated with the same objectives. One of the difficulties with flotation control has been to recognise and define clear and precise control objectives. More emphasis is now placed on cleaner control which has the advantage that the objectives are usually well defined. A number of flotation control systems which cover a range of control system types is discussed. Based on this accumulated experience,a list of good and bad practice in flotation control is Proposed.

Jan 1, 1983

This paper describes the application of the Total Productive Management (TPM) technique as a performance improvement initiative for a coal mining operation. It discusses the objectives of TPM, with the driver for improved production performance being the Overall Equipment Effectiveness (OEE) of the equipment or process, and with the development of "ownership" as the behavioral approach to equipment management and continuous improvement through cross-functional and area-based teams. It illustrates the concept of equipment management as defects management.The scope for application of TPM to the coal mining industry is immense. The harshness of the operating environment can be a major generator of equipment defects, and a current paradigm in the industry accepts these defects as an unavoidable outcome defining maintenance costs in this environment. However recent benchmarking studies have highlighted that maintenance costs per operating hour in some mining operations are more than double the vendor's estimate of "best practice". The paper refers to these studies which also compare maintenance costs of fixed and mobile plant and equipment to "best practice" outcomes in comparable process industries.

Jan 1, 1998

By Williams SR

Column Flotation cannot be used indiscriminately. Based on extensive pilot plant experience at Lakefield Research, a number of limiting parameters have been identified for the application of column cell flotation. Parameters of importance are the use of wash water, flotable mineral content, pulp viscosity, type of mineral selectivity being sodght and degree of mineral liberation. The paper discusses when wash water should be used and the positioning of a column within the circuit as this is important to maintain a sound water balance for the circuit and prevent excessive circulating loads. Other areas of debate are pulp chemistry, very low and high weight recovery, for which the conventional column is a poor selection of equipment, and treatment of complex ores, where the separation of valuable minerals is more difficult than non-sulphide, sulphide mineral separation. Based on these observations, the application of column flotation must be carefully considered or can be optimised.

Jan 1, 1993

By Misk A

Several logging methods are presently available to the oil industry for the evaluation of formation porosity: the Sonic and Neutron logs are already widely used, the Gamma-Ganmia log is being progressively introduced. The readings of these instruments are primarily a function of the rack-porosity, hence the general term of "porosity tools". Apart from porosity, however, other variables such as type of fluid in the pores, nature of matrix and degree of shaliness have an important influence.The response of each device is a different function of such parameters: therefore, a cci bination of porosity tools can lead to information on these variables in addition to the evaluation of effective porosity.For example, the presence of gas; rather than water or oil, in a formation which is not deeply invaded, will tend to give Neutron derived porosity values which are too 'low; on the other hand, the Sonic derived porosity: value will be too high in such- a case. For the same porosity, the Sonic gives a longer transit time in sandstone than limestone, whereas in the low porosity range, the Neutron will read more counts per second in a sandstone than in a limestone of the same porosity. The presence of shale also affects the readings of the various porosity tools in different ways so that the combination of two or more methods may lead, in some cases; to an evaluation of both the-effective porosity and the shale, content.In conclusion, it may be said that the various porosity tools pre-sently available, are, to a large extent, complementary, and that in many problems the use of two porosity tools, instead of one, is very likely to bring valuable additional information.

Jan 1, 1962

By J Galvin

This paper addresses the actions of the Australian mining industry, its regulators and educational providers towards ensuring that a pool of competent mine managers is maintained in Australia and that mine management remains a desirable career path for future mining professionals. The Australian and global mining industries are experiencing an acute skills shortage. Mine managers, traditionally drawn from the ranks of mining engineers, are at the sharp end of this shortage. Exacerbating the shortage is a perception that a professional mine manager is not an attractive career option. This perception is influenced by the following forces which combine to make the role of a modern mine manager very demanding:legislative requirements for owners and managers to ensure (guarantee) the safety and health of employees; an increasing trend towards prosecution over exposure to risks to health and safety a need to be more aware and responsive to community and environment; financial, technical and æpeopleÆ pressures traditionally associated with the job of managing a mine; and mine management roles being filled by younger and less experienced professionals. Universities and other educational providers have the challenge of both ensuring that undergraduates are exposed to these issues during their study and continuing to promote mine management as a desirable career option. Anecdotal and statistical evidence indicates that young graduates are choosing and remaining in technical roles rather than taking on the challenge of mine management. Furthermore, it is suspected that the issues referred to above are contributing to the low retention rate of young professionals at mine sites. The challenges are not insurmountable, however. This paper reviews the initiatives of industry, the regulators and educational institutions in addressing these challenges. It includes a focus on:prosecution policies and their impacts, tertiary education program content and delivery modes, CPD initiatives of the Mine Managers Association of Australia, and alternative pathways for obtaining mine management qualifications.

Jan 1, 2006

By N Slade, D Kennedy

Optimal throughput is a key objective for the successful operation of any manufacturing or processing business. In the mining industry in particular, in order to obtain maximum return on the significant capital investment in the physical assets involved, ensuring continuous throughput is a major focus for the complete leadership team. Failure to meet throughput objectives becomes a major source of distraction for management which too often attempts to solve shortfalls by æforcingÆ and æenforcingÆ production targets. This focus on the short term and the lack of attention to addressing root causes frustrates operators who attempt to satisfy unattainable short-term targets and lose sight of the long-term goal. Mount Isa Copper Operations, Xstrata Copper, North Queensland, had ambitious plans to increase throughput volume by ten per cent within a four month period to allow budgets to be achieved within the financial year. To achieve this, the process had to overcome the interplay of a multi-node (æsiloedÆ) production system and its associated inventories, each node, of which on the face of it at least, had more than enough ænameplateÆ capacity to meet these plans. However, the actual volume achieved at the end point of the system was well below this nameplate capacity and the system operated with an extraordinarily high standard deviation. The key issues in terms of making or exceeding plan were: how to substantially reduce the variability of the system and managing the inventories between nodes, how to synchronise throughput between the production nodes, and how to improve the decision-making ability within the process. In this paper, the implementation team has shown that a revolutionary process view of the operation together with appropriate planning decisions allowed increased throughput to be achieved without further capital investment.

Jan 1, 2006

By R M. Tosdal

Intrusion related ore deposits are widespread in the Central Peruvian Cordillera Occidental and adjacent high-plains to the east and include porphyry Cu (-Au, Mo; eg Morococha), Cu-Zn (Pb-) skarn (eg Antamina), Pb-Zn-Ag carbonate hosted vein deposits (eg Uchucchacua), cordilleran base metal (eg Cerro de Pasco) and epithermal deposits (eg Quicay). Geochronology and petrochemistry of intrusive rocks associated with mineralisation reveals that: most ore deposits were emplaced in the late middle to early late Miocene; and are related to calc-alkaline granodioritic igneous rocks with Sm/Yb >3, Sr/Y >40 and Y/Th <1.5. The largest deposits, including Antamina, Colquijirca and Cerro de Pasco are associated with intrusions with Sm/Yb >4 and which, as indicated by Pb and Sr isotopic data, have undergone relatively moderate middle and upper crustal assimilation. The chemical signature of igneous rocks related to mineralisation likely reflects melt equilibration in the lower crust at a crustal thickness of more than 45 km. Mineralisation was favoured by a change from normal to flat subduction, resulting in increased compression, crustal thickening and subsequent cessation of the magmatic arc. Premiocene ore deposits do occur, but are restricted to a broad E-W corridor between Uchucchacua and Milpo and probably were controlled by a crustal-scale structural discontinuity across the strike of theAndes. Not all igneous rocks with high Sm/Yb and Sr/Y ratios did acquire their trace element signature in the lower crust. Petrographic and Pb isotopic evidence indicates shallow crustal hornblende fractionation or assimilation of pelitic material as possible causes for high trace element ratios in some rocks. These are apparently unrelated to polymetallic mineralisation. Thus, critical evaluation of petrographic and geochemical data in metallogenetic studies, especially in areas with complex basement architecture such as Central Peru is critical and should not be reduced to simple trace element ratios. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By S La Brooy, C Fountain

Throughout its history the mining industry has focused on the highest-grade deposits sited in the most convenient locations. The burgeoning global population and higher standards of living not only increase the demand for mineral products but also make it harder to mine and process them. The future will include the development of lower-grade, more complex orebodies, and orebodies in difficult locations. The industry will be expected to provide for humanityÆs needs while reducing its environmental footprint and maintaining profitability. This paper reviews some of the likely adaptations in mineral processing that will occur over the next 20 years. The challenges inherent in adapting to lower grade and more complex materials might be exacerbated by such factors as the availability of water and low-cost energy. In underground mining, higher energy costs are likely to foster further developments in underground preconcentration, especially for ores that can be upgraded at relatively coarse sizes. The adoption of underground crushing could also render material amenable to semi-dry preconcentration options such as might be achieved by the rotary classifier developed by CSIRO and being commercialised by RCR Tomlinson, or more modern versions of the hand-sorting of ore that use sensors based on colour or other suitable rock properties. The cement industry and some gold roasters have used the alternative of dry grinding and classification, which might also have a part to play in dry processing. There is also likely to be increased interest in options such as in situ leaching that further minimise the surface disturbance. Underground operations will have to balance the energy savings from reducing the amount of material brought to the surface and reduced surface disturbance against the practical limitations of installing and maintaining processing equipment underground. On the other hand, surface disturbance and energy issues in open cut operations will be balanced by potentially lower mining costs and higher overall recovery from the deposit.

Jan 1, 2008

By R Huntley, D Sims

Pajingo gold mine produces over 240 000 oz Au per year from underground mining using longitudinal bench stoping methods with a 15 m sublevel interval. Average mine head grade is around 12 g/t Au, contained within quartz veins between 0.5 to 16 m wide. The veins dip steeply (>60¦) and exhibit strike variations which lead to many curved and meandering drive/stope geometries. Unplanned dilution at Pajingo is predominantly controlled by fault planes that subparallel the vein and commonly lead to slabbing failure from the stope walls. Initial efforts at determining maximum spans were based on using the Stability Graph method of stope stability. However the method had a number of shortcomings that did not address mine site observations, including previous mining, interaction of different joint sets and the presence of discrete shears which resulted in poor prediction of stability. A method was developed to rate the risk of dilution for a stope based on observations made in the ore drives. The method utilises profile mapping of the ore drive, structural features observed and the orebody itself, on 10 m spaced sections along the ore drive. A matrix of factors determines the dilution risk for stoping at the time of mapping and the rating is transferred to longsection plots in the office. The dilution risk rating is used to determine the position and density of cable bolt support aimed at lessening the risk, and can be used to review blasthole designs prior to finalisation. The method has been used for more than two years and has proven to be a good indicator of potential unplanned dilution (ie waste outside of ring design). A recent review of the dilution risk mapping process has indicated it is assisting in reducing the impact of dilution at the operation and has the scope to be utilised further in the design process.

Jan 1, 2002

By Juniper LA

ERM Consultants Pty Ltd was established in 1980 for the purpose of introducing a disciplined coal technology and power station planning service, to support Australia's efforts in establishing a major export steaming coal industry. At that time, major coal exploration programs were mounted on more than 50 potential export coal deposits with proven open-cut reserves to export 200 Mt/a of coal. The fact that Australia achieved an export trade of only 30 Mt/a, equivalent to the energy requirements for a population of around 5 million people, illustrates the very small achievement to date. The main reasons for this small export steaming coal growth have been: 1. Failure to convince potential overseas coal buyers of the benefits of coal-fired power generation, and the ability of proper power station design to overcome environmental problems, and achieve reliable operation and long life when burning Australian coals. 2. Failure to promote Australian power engineers to advise on the use of Australian coals, resulting in Northern Hemisphere power station experience dominating in market countries. 3. Failure of governments to draw on privately practising Australian power engineers and coal technologists in technical workshops, presentations and assistance to overseas countries, to ensure that personnel whose business it was to serve the follow-on needs of countries were readily available. The result of these failures has been that: 1. Only a fraction of prospective overseas coal-fired power projects have proceeded. 2. Australia has had no influence in the design of overseas power stations to ensure that potential customers would be confident that Australian coals could be reliably burnt in their boilers.

Jan 1, 1987

Geostatistical conditional simulation is a method to assess variability and risk in mineral deposits and the tool has wide potential applications in the iron ore industry. Correct reproduction of multivariate relationships is important in iron ore simulation, especially between Fe and impurities such as Al2O3, SiO2 and P. The turning bands simulation method, using a full model of coregionalisation for multiple attributes, is the main multivariate conditional simulation algorithm used in the Western Australian iron ore industry. This paper discusses the results of a more recent approach using minimum/maximum autocorrelation factors (MAF) to transform and decorrelate the multivariate data prior to independent sequential Gaussian simulation (SGS). MAF-SGS results are compared to those of the turning bands approach in the Yandicoogina channel iron ore deposit (CID), and both methods performed well in simulating Fe, SiO2, Al2O3 and P distributions. Extensive checking of simulations showed that both approaches could reproduce multivariate statistics and spatial continuity of the original conditioning data. Both approaches reproduced the histograms and variography of input sample composites. While the MAF-SGS approach requires additional transformations when compared with the single normal scores transformation required for the turning bands method, MAF requires only that the direct semivariograms be modelled. In contrast, using turning bands with multiple attributes requires modelling a full linear model of coregionalisation, which can be difficult to model because of the need to ensure the model is positive semi-definite. Turning bands may be preferred if there are a modest number of correlated variables allowing construction of a linear model of coregionalisation that adequately models the multivariate behaviour. MAF-SGS is preferable for larger numbers of correlated variables. Both MAF-SGS and turning bands methods performed well in conditional simulation of correlated variables at Yandicoogina.

Jan 1, 2007

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991