Search Documents

By I Taylor, M Nugus, C Gordon

Resource estimation and selective mining of structurally complex, high nugget orebodies presents a major challenge to the Mine Geologist. At the Golden Pig BIF-hosted gold deposit in Western Australia, an estimation method has been developed that replaces an assay-based resource estimate with one based on mineralisation intensity. Subjective coding of the mineralisation intensity has a more robust connection to local grade than drillhole assays. Indicator variograms of the five mineralisation codes are well structured with anisotropy directions similar to observed structural controls. The proportion of each mineralisation code is estimated and a weighted average of the average grade of each code calculated for a block. Initial validation has shown that the model is a good predictor of the mineralisation intensity, and the application of appropriate local average grade for each mineralisation code gives a reliable block grade estimate.

Jan 1, 2003

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989

By Richardson F. A

Techniques for flotation optimisation were investigated at Cobar [lines Pty:Ltd., in anticipation of the proposed installation of a computer and on-stream analysis. Successful laboratory and pilot plant tests for flotation performance optimisation using the Simplex Evolutionary Operation Technique (Simplex) lead to a full scale plant test using this method. The index developed for" Simplex response evaluation of flotation performance was based on metallurgical and economic criteria. This index was further modified to minimise the effect of head grade fluctuations. The test program was carried out on one of two parallel copper flotation circuits to allow comparison with normal "manual" operating control, and was conducted for thirty eight shifts. Results from the test section operating under Simplex direction were superior to those obtained using normal "manual" operating techniques and demonstrated the use of the Simplex Evolutionary Operation Technique as a method of reducing reagent consumption in flotation but, at the same time, maintaining satisfactory metallurgical performance. Experience in the use of the technique indicated the need for modifications to the rules of Simplex operations. Modifications were proposed, tested and appeared satisfactory.

Jan 1, 1973

An established method exists for the computation of rope lifetimes for shaft hoisting applications in the mining industry. In an earlier study, during the 1990s, an initial comparison of the calculated and actual rope life for various types of hoisting plants showed reasonably good correlation. In the meantime the calculation method has been developed further. The rotation behaviour of the rope during hoisting and the effects of multilayer spooling on drums are now considered in the assessment of expected rope lifetimes. The ability to determine an estimate of rope life in advance is particularly useful for mining companies. Such analysis allows them to predict the effects of rope choice in their particular application and thereby reduce the total cost of rope ownership. Such calculation techniques also allow designers of winding plants to identify aspects of the hoisting configuration that may negatively affect rope life. Often small (low-cost) changes, like increasing the diameter of head sheaves, can result in considerable improvements in rope performance. This paper describes the extended lifetime calculation method and gives further examples of the comparison between actual and calculated rope lives for operational double-drum mine hoists.

Jan 1, 2005

By D J Rawlings

The Palaeo- to Mesoproterozoic McArthur Basin contains a thick (-10 km) intracratonic platform cover sequence of unmetamorphosed and relatively undeformed sedimentary and volcanic rocks (Pietsch et al, 1991). It covers an area exceeding 180 000 km2 of the North Australian Craton (Figure 1), overlying segments of the older deformed basement and transitional igneous units. Volcanism in the basin (including transitional domain) followed a four-phase pattern. These phases are geologically distinct and widely distributed, and are also recognised beyond the McArthur Basin in many similar-aged tectonic provinces in northern Australia. The four phases are described briefly below. Regional and structural nomenclature used refers to Figure 1. A stratigraphic correlation diagram is presented in Figure 2.

Jan 1, 1994

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By A S. Bamber

Mining is the oldest industrial practice on the planet with a history dating back over 3000 years. Since the early iron age ores have been extracted for use in a variety of contexts by humankind, from domestic to military, transport and more recently for complex industrial applications. Mineral exploration and extraction has evolved from the early exploitation of primary metal occurrences in relatively small quantities such as iron, gold, coal and copper, to the bulk mining and extraction of highly complex polymetallic oxides and sulfides today. Since the industrial revolution, mining practice has evolved substantially to support an increasing range and quantity of required metals and to accommodate the increasing scarcity of high-quality sources of these metals. A common response to the increasing scarcity of mineral resources has been to expand production through simple economies of scale, thus diluting fixed costs. This approach, however, is increasingly ineffective in the face of current trends, that include increasingly complex mineralogy, increasing pressure on environmental footprint - energy in particular, and increasing scarcity of capital for the construction of presently popular æmega-minesÆ. This paper examines historical trends and current practice in mineral exploitation in the light of the current global revolution in social, environmental and economic values as the projects move towards a vastly different topology for the industry for continued success in years to come.CITATION:Bamber, A S, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Magnetic Separators have a wide application in dry separation processes, frequently in conjunction with High Tension Separation. Dry processes can frequently be superior to established processes in more commonplace mineral associations. A system of dynamics is postulated and the forces operating ar'e examined, together with a method of evaluating the effect of operating variables. Practical applications of these theories to obtain optimum results on an individual separator, and various separations using a laboratoryroll type separator are described.Practical Flowsheets are of two main types, the first consisting of a series of scalping operations, the second for rougher, cleaner, and scavenger operations with middling recirculation. Some common separation problems with certain mineral associations illustrate the need for different approaches for different mineral associations. A table of mineral separation characteristics is appended, from which amenability may be tentatively estimated.INTRODUCTIONMagnetic separators are widely used, either alone or in conjunction with other wet and dry concentration devices, for the upgrading of a variety of minerals. The high standards of efficiency attainable in dry mills, together with reduced operating and labour costs, are slowly becoming apparent in a wide variety of plants. The combination of wet and dry concentration plant familiar in beach sand mining is finding application for such processes as upgrading a crushed chromite product, and production of clean scheelite,cassiterite, and other concentrates. Other dry beneficiation processes (such as the high tension beneficiation of iron ore, and the benefiGiation of asbestos) avoid the use of wet processes completely.Dry separation processes are likely to be applied more widely as their possibilities become more generally known.

Jan 1, 1958

By Whittaker B. N, Reddish D. J

This paper presents the physical modelling results of subsurface fracture development associated with Iongwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results haióbeen obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camels. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By M Ewart

The securing of a reliable water supply for a prospective mine in the North West Queensland Mineral Province is usually one of the most influential factors in determining the mine's feasibility. The Ernest Henry Mine required a reliable water supply to serve a demand estimated at feasibility stage to be up to 20 ML/day. Numerous options were considered before a decision was made to construct a 113 km long pipeline from Lake Julius as this was the most cost effective, reliable source of supply. The North West Queensland Water Pipeline is a multi-user, Queensland government funded project initially supplying up to 7000 ML/year of water from Lake Julius to Ernest Henry Mine, with provision made for expansion to serve future users in the region. This paper discusses the history of the pipelineÆs development, together with a summary of the scheme's design features. Environmental and licensing requirements, construction and operational issues are also discussed.

Jan 1, 1998

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By G Newling

Zinifex Rosebery Mine is a lead-zinc underground mining operation located at the base of Mount Black, on the West Coast of Tasmania. Mining activities at the Rosebery Mine have been undertaken for over 100 years, and it has been operating in its current form for over 60 years. A large surface and underground exploration drilling program over the last 18 months has increased the mineÆs expected mine life from five to 12 years, with expectations that over the next 18 months as the program continues this will swell to 20 plus years. Zinifex Ltd secured Rosebery Mine in April 2004 and commissioned a detailed life-of-mine (LOM) study on all aspects of the operation. One of the most detailed sections of this report was on the state of the current ventilation system. It was identified in this report that for mining at the current depth of approximately 1100 m to continue a minimum 30 per cent increase in ventilation quantity was essential, as well as a likely requirement for a refrigerant cooling plant for each of the two deepest panels, the K and P lenses. It was identified that Zinifex did not have personnel with the expertise in underground refrigeration to manage and implement a project of this nature. A second report was commissioned with Bluhm Burton Engineering (BBE), a South African firm specialising in both surface and underground large-scale refrigeration plants. BBE concluded that two refrigeration plants were required to provide the necessary cooling power in the lower sections of the mine. In 2005, with BBE as technical consultants, Zinifex Rosebery Mine embarked on a project to commission two underground refrigeration units capable of lowering the wet bulb temperature at the decline face by four degrees centigrade. This paper is intended to give the reader an overview of: Rosebery Mine operations,Rosebery underground refrigeration project,technical difficulties associated with implementing an underground refrigeration system, andkey learnings to date.

Jan 1, 2008

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993