Search Documents

By Hollis R. G, Tuppurainen J. M I

Improved control of non-ferrous sintering operations requires the on-line measurement of sinter quality. No on-line measure of sinter quality is currently available, however, previous work has shown that the raw mix chemistry and peak sintering temperature determine the mineral phases formed and hence the resulting Blast Furnace behaviour. Control of these factors should therefore lead to improved quality control. In this paper, the development of a simplified heat and mass balance model of the Sinter Plant at Mt Isa is described. The model used available plant data to calculate raw mix composition and a simplified reaction scheme to predict sinter composition. The extent of reaction is inferred from the flue gas analyses. Off-line testing of a dynamic version demonstrated that actual plant performance could be predicted with reasonable accuracy.

Jan 1, 1989

This paper traces briefly the reasoning which led to the decision to extend the existing internal shaft at the Rosebery Mine and to instal underground a larger winder (No. 2 Hoist) with capacity to handle all hoisting requirements to a depth of approximately 2,500 ft. on an incline varying from 83" to 55" to the horizontal. It then covers the specifications and selection of the winder, the design of the winch chamber, rope raise and bins, the excavation, support and lining of the chambers and the transport to site and installation of the machinery. Finally a brief description is given of the mechanical and electrical parts of the winder.INTRODUCTIONThe existing shaft winder on the internal inclined shaft situated on No. 8 Level of the Rosebery Mine had reached the limit of its capacity. Hoisting 21-ton capacity skips in balance, with a 13/16-in. diameter rope, it required four layers of rope on the 3 ft. 6 in.drums to reach the loading station under No. 12 level at a depth of 864 ft. (Fig. 1). This entailed heavy wear on the multi-layered rope and heavy stresses on the cheeks of the drums. Continuous working on three shifts was necessary to handle ore, men and materials, and a hold-up from any cause whatever meant an interruption to production on the lower levels of the mine. The maximum output of the hoist whilst hoisting from the No. 12 level loading station was 50 tons per hour. It was obvious therefore, that a larger winder was required if output was to be maintained.Diamond drilling had proved the existence of sufficient ore at depths well below No. 12 to warrant exploitation and a decision had to be reached on the means of hoisting this ore.

Jan 1, 1958

By S Hapugoda, M Peterson, A Haileslassie, A Poliakov, E Donskoi, L Lu

Most metallic iron in the world is produced in blast furnaces from different feed stocks – sinter, lump ore and pellets. Sinter is the main iron-containing feed to the blast furnace and can constitute up to 70–85 per cent of the total ferrous burden. As sinter quality is a key element for stable blast furnace operation, the textural, chemical and physical characteristics of the sinter are very important. Two major factors that affect sinter strength are mineralogy and porosity. This study utilised optical image analysis (OIA) to characterise sinter mineralogy, and the results were compared to those obtained by manual point counting under the optical microscope.Two major mineral characteristics of iron ore sinter are the presence of primary (unreacted) and secondary (derived from melt) hematite. Standard OIA, which is based on RGB thresholding, is not able to distinguish them as they have the same reflectivity; however, primary and secondary hematite in iron ore sinter have a different morphology. The CSIRO-developed OIA software Mineral4/Recognition4 has a unique feature to identify various textures/morphologies of the same mineral. Together with other capabilities of the Mineral4/Recognition4 software, this feature was used to identify different types of hematite and silico-ferrite of calcium and aluminium and other common sinter phases, such as magnetite, larnite, glass and remnant aluminosilicates.A visual comparison of the sinter mineralogy present in optical photomicrographs and that present in the mineral maps created automatically by the Mineral4 module of the CSIRO software confirmed the accuracy of the automated mineral identification.CITATION:Donskoi, E, Hapugoda, S, Lu, L, Poliakov, A, Peterson, M and Haileslassie, A, 2015. Advances in optical image analysis of iron ore sinter, in Proceedings Iron Ore 2015, pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S Bandopadhyay

The seasonal fluctuations of the dust content in Arctic mine environments and the environmental variables affecting the intensity of dust production are qualitatively well known, but quantitative models that allow simulation and prediction of dust generation and the effects of engineering control of thermal regime on the mine environment are still non-existent. In Arctic mines, the migration of moisture in the surrounding rock mass releases fine dust by freeing it from the ice matrix allowing it to escape into mine airway. The migration of moisture is the direct cause for the production of mine dust and heat is the primary driving force. This paper examins the heat and moisture exchange between the ventilation air and the surrounding rock mass in frozen ground, placer mines in the Arctic. Based on the simulated results of a coupled heat and mass transfer problem with phase change, methods of dust control have been identified for mines in the Arctic.

Jan 1, 2005

By G D RICHMOND, Campbell J. J

Aberfoyle Limited has developed the Hellyer complex base metal sulphide deposit located in North West Tasmania. As part of exploration and feasibility study, the ore was extensively tested, including trial milling, and was found to be very fine grained and to have poor flotation selectivity. Substantial innovation was required to produce saleable concentrates at acceptable recoveries and costs. Efforts were made to reduce operating costs, to improve metallurgical performance and to improve work organisation. These efforts were pursued both in design and in subsequent plant operation. This work has resulted in a very competitive operation with production costs in the lowest quartile of the industry. Examples of the measures taken are presented and the results are evidenced by improved plant performance since commissioning.

Jan 1, 1992

Large scale rhyolitic volcanism is an important process at some convergent plate margins because it leads to chemical differentiation of the upper.-crust and is responsible for the production of long lived near surface thermal anomalies; the Taupo Volcanic Zone is.a Quaternary example. The main features of the magmatic systems-of the zone. are the existence of large high level chambers containing homogeneous silicic magma which erupt at intervals of thousands to tens of thousands of years. Geochemical work on the deposits resulting from these eruptions has shown that with few exceptions the magmas have been remarkably uniform in their . composition throughout the history of the zone although individual batches with lifespans of the order of. one hundred thousand years can be recognised by subtle differences in trace element ratios. Basalt is a rare proportion of the rocks exposed at the surface but has played a major role as a medium for heat transfer and as an end member in chemical mixing processes.

Jan 1, 1987

By Y Mita, T Iwama, R Inoue, S Ueda

In the iron and steel manufacturing industries, efforts are being made to achieve carbon neutrality by 2050, and the transition from a coal-based steelmaking process to that utilising renewable energy is being pursued. An alternative process in which directly hydrogen-reduced iron is melted in an electric furnace is being investigated. It is known that foaming slag reduces heat loss from the steel bath in electric arc furnace, but iron loss due to the suspension of steel particles in the slag is indispensable. To improve the separation of steel particles from the slag, the control of the slag viscosity is important. Although the slag viscosity has been extensively studied, in those studies the slag was considered to be a simple liquid. However, in actual operations, slag is a multiphase fluid consisting of solid, gas and liquid phases. Therefore, in this study, by measuring the sedimentation velocity of titanium, stainless steel and glass spheres in an aqueous glycerin solution containing bubbles generated by the reaction between NaHCO3 and C2H2O4, the apparent viscosity of the gas-liquid fluid was evaluated based on Stoke’s law. It was found that the apparent viscosity of the gas-liquid fluid is larger than the viscosity of liquid phase and depends on both the bubble volume ratio in solution and the density of the falling solid sphere, and the apparent viscosity was different from that previously obtained by the rotation method. The apparent viscosity derived from the sedimentation velocity of solid spheres changed depending on the specific gravity of the ball. This is because the apparent viscosity is derived from the velocity of a ball falling in a static bubble in this method, whereas that is derived from the force applied by a stationary flow in the rotational method.

Aug 21, 2024

Current attitudes by exploration companies towards working on another party's exploration permit or equivalent vary widely. That this is so is due to the virtual absence, on the one hand, of anything in the mining legislation in any jurisdiction that establishes what are the exclusive rights to explore, as opposed to apply for a mining tenement, that the grant of such an authority conveys on the holder, and on the other hand, of any code of ethics or set of guidelines to proper practise. By contrast, in most states and territories, if not all, it is an offence to enter onto a mining tenement, other than to cross it, without the consent of the holder, although until recently most field personnel would have been unaware of this and most explorers would have transgressed at one time or another. A similar vacuum exists where aerial surveys are concerned. There are in fact no guidelines. It has always been assumed that a party wishing to carry out such a survey was free to do so, without even an obligation to notify the holders of any tenements or permits in the area to be surveyed, let alone make available to them any data from the survey. Concepts of 'geophysical trespass' now being tested in the US also raise the possibility that data won from adjoining ground using geophysical techniques may be privileged. Attitudes now appear to be changing. In the absence of legislation or any code of practise, what does the industry regard as ethical behaviour? Do we need to define the rights and obligations of various parties more clearly, and if so, what should they be and to what extent will it be necessary to confirm them by legislation as opposed to adopting a code of practise? Will the existence of such a code in fact improve corporate practise?

Jan 1, 1995

By D E. Langberg, J S. J va, D R. Swinbourne

Specifications on the types and levels of impurities tolerable in metals are becoming increasingly stringent, and are pushing the limits achievable with conventional refining technologies. Particularly difficult is the removal of electrochemically noble elements with low volatilities, such as copper, from more active host metals such as lead, iron and aluminium. Electrochemical refining, utilising the ability of certain solid electrolytes to selectively transport copper or other impurity cations away from the molten host metal into a separate refining phase, may provide an answer to this problem. Numerous studies on solid electrolytes used in concentration sensors have been reported, as well as a limited number on metal refining. Oxygen anion conducting solid electrolytes have been applied to the deoxidation of copper and steel while cation conductors, eg ¯ -alumina and Nasicon materials, have been used to remove lithium and sodium from aluminium. However, solid electrolytes have yet to be applied to the removal of noble elements. The behaviour of solid electrolytes under the extreme conditions of molten metal refining is not well understood. This paper will examine the potential use of solid electrolytes to remove noble metals such as copper from active host metals such as iron. The suitability, and selection criteria of available solid electrolytes for implementation in the metal refining industry in the future will be discussed. In particular, the stability of Cusicon, a copper superionic conductor potentially suitable for use in metal refining, has been assessed and the results of the experiments are presented.

Jan 1, 2000

By I Warren, M P. Simpson

Adularia-sericite epithermal ore deposits have well-documented alteration mineral zonation patterns with distinctive geochemical signatures. Proper use of whole-rock geochemistry can provide useful vectors for exploration and can enhance efforts to characterise and quantify the mineralogy and intensity of hydrothermal alteration.   Analyses of Au and Ag provide the most direct vectors to orebodies, and pathfinder elements such as As, Sb, Hg, Zn, Pb and Se are similarly zoned around at least some orebodies. However, the minerals that contain these elements occur almost exclusively in veins, and therefore identifying geochemical vectors related to wallrock alteration that is zoned outward from orebodies is crucial for effective exploration.   Distal alteration zones contain quartz-illite-chlorite-carbonate-pyrite, whereas samples proximal to veins contain quartz-adularia-pyrite, with lesser though variable illite-chlorite-carbonate. Therefore, adularia-sericite epithermal ore deposits show K alteration in their cores. The resulting K-metasomatism can be evaluated in several ways. Areas that have been most intensely altered are commonly characterised by highest K contents, but these results can be complicated by variations in rock type across the prospective area. Potassium mass balance results provide a robust and rigorous assessment of K-metasomatism, however, knowledge about the composition of fresh rocks and correct identification of fresh precursor compositions of altered rocks are required. Three alteration indices provide effective evaluation of K-metasomatism: 1.   the K number, which is the ratio K/(2Ca+K+Na) (molar); 2.   Barrie values [(K2O * 100) / Sr]; and 3.   the Rb/Sr ratio. In most places these provide similar vectors, although K numbers can be complicated by the appearance of hydrothermal calcite and/or albite.   Plots of K/Al vs (2 Ca + K + Na)/Al (molar) allow estimation of the intensity of K-metasomatism and its mineralogical products, thereby complementing traditional XRD and petrographic studies of alteration minerals.

Jan 1, 2005

By K Voigt, B Bolton, C Rumble

The Ok Tedi copper and gold mine is owned and operated by Ok Tedi Mining Limited (OTML) and is located in the Star Mountains of the Western Province of Papua New Guinea. Waste materials (both sulfidic and carbonate materials) from mining operations, comprising 55 Mt of waste rock and 31 Mt of tailings per annum, are discharged into the headwaters of mine area creeks where erosion and sediment transport carries significant proportions of the total waste into the Ok Tedi and Fly River systems. The tailings are potentially acid forming (PAF) while the waste rock has been strongly acid consuming with an excess of acid neutralising capacity (ANC) due to the high proportion of limestone waste. Tailings and waste rock are eroded into the river system and transported to the lower Ok Tedi and floodplains where deposition takes place. Because of concern due to vegetation die back, a dredging operation commenced in March 1998 to remove the sand fraction from the main river channel. OTML identified a potential future ARD risk from the stockpiled sands due to reduce limestone production at the mine and sulfide/carbonate mineral segregation in the river system and in the dredge sand stockpiles. This paper describes the structure and framework of an empirical model developed to assist OTML in planning ongoing mining operations to control ARD. Modelling identified the need to provide additional mined limestone to prevent future ARD generation from material deposited in the mine area creeks. With the additional limestone, the ARD risk in waste rock storage areas and in the Ok Tedi and Fly River sediments is predicted to remain low due to the combined effects of high ANC, high alkalinity of natural waters and high moisture contents (mostly fully water saturated). However, monitoring and modelling indicate that the ARD risk from the stockpiled sands will increase substantially during the remaining years of the operation. OTML have initiated programs to identify and evaluate options to mitigate this risk.

Jan 1, 2003

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

When a major mineral find has been announced the general perception is that a battle between Aborigines and the mining company involved will inevitably occur.It is a fact that many miners in the past have not had a good relationship with Aborigines because of their indifferent attitudes towards them. They saw no common future and went their particular way. However, attitudes have changed significantly since Noonkanbah and both miners and Aborigines are seeking common ground in order to achieve mutual benefits from the establishment of a mine on or near Aboriginal land. There are many obstacles that both miners and Aborigines need to overcome inordertofindthiscommongroundtoachieveawin/win situation. The obstacles can be found in entrenched ideas and practices which need overhauling, not the least of which emanate from government policy and requirements.Without going into specifics, the Noonkanbah incident during the 1970's where Aborigines and their supporters confronted miners who were ordered by the Western Australian governmentto drill on Aboriginal land, polarized Aborigines and miners. Since this incident, many Aborigines, particularly those in the cities, have had the attitude that mining and Aboriginal culture are in direct conflict. Aboriginal opinion is generally shaped in the larger cities through mass media coverage of the opinions of urban Aborigines and their supporters. Through no fault of their own, these Aborigines were removedfromthe land of their ancestors and have notlived atraditional Aboriginal life-style for a number of generations and most have little knowledge of, nor have had involvement in, traditional Aboriginal lore and culture. For the most part these people live in awestern life-style and few still know their language. They generally have high profiles, often giving viewpoints that are wrongly considered "Aboriginal" and supposedly representing all Aborigines. This group is very different with their thought processes and values from those Aborigines who live on their own traditional lands with a traditional life-style, and practise their age old ceremonies. Their tribal values are based in their relationship with the land, expressed through complex religious ceremonial rites of song, dance and legend. Today this group is very much diminished in numbers but nevertheless in the region of the Gulf of Carpentaria there is a high proportion ofpeople who practise their lore, speak their own languages and pass on traditions to their children. It is well documented in the history of Australia that Aborigines have been decimated in numbers and whole tribes have been wiped out. Certainly in this region the experience has been no different.

Jan 1, 1993

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

By Lewis RW, Tullemans FJ, Gallo JB

Gold mineralization at Kidston occurs in a semicontinuous zone near the margin of a large, late Palaeozoic breccia pipe. The pipe is ovoid in plan, funnel-shaped in cross section and straddles a contact between Proterozoic metamorphic and granitoid rocks which are intruded by a swarm of late Palaeozoic acid dykes. Rock fragments within the breccia pipe reflect the enclosing country rocks and mix in various proportions to form gradational lithological domains. Most of the gold is free and is located in the breccia matrix and in a set of inwardly dipping sheeted quartz veins which kink around the pipe margin. Sulphide minerals, dominantly pyrite, occur as disseminations in the breccia matrix and as aggregates in the cores of quartz veins. Hydrothermal altLration is pervasive within the breccia and is most intense in areas with the highest percentage of acid dyke fragments. Sericite and carbonate are the main alteration minerals. An empirically developed genetic theory for the formation of the breccia pipe and attendant mineralization involves magmatic and post-magmatic processes associated with the intrusion of a granitoid body to a shallow level in the crust. Economic evaluation of the deposit relied heavily on the results of diamond drilling. Both polygonal and geostatistical reserves were calculated and found to be in close agreement. Geostatistical reserves are considered to more closely reflect the tonnes and grade achievable during mining. Daily geological mine routine is strongly biased towards grade control allied with the practical aspects of open-pit mining. Tonnage/ grade correlations between ore blocks geostat- istically generated from exploration diamond core results and ore blocks generated from high

Jan 1, 1986

By R C. Morris

Supergene lateritic iron ores are uncommon when compared with the vast tonnages of BIF-hosted microplaty haematite ores of the world or with the dominant supergene mimetic martite-goethite ores of the Hamersleys. In Australia and to a lesser extent in India and South America, mimetic replacement of gangue minerals by iron hydroxyoxides is a major factor in forming supergene iron ore from banded iron-formation (BIF) and results in the superb preservation of all of the original BIF features. This includes primary banding down to the finest inclusions, as a result of pseudomorphing of the BIF gangue at depth by goethite. The enrichment as a whole is an absolute accumulation of Fe at depth, dissolved from the surface BIF, and a removal of the gangue elements without loss of the original BIF mineral textures. Thus the ores grow upward to meet the downward destruction of the surface BIF by erosion. By contrast the supergene lateritic ores including the 'blue dust ores' are residual ores resulting from the relative accumulation of Fe. In the supergene lateritic ores derived from BIF, removal of the gangue is accompanied by repetitive solution and reprecipitation by secondary haematite and goethite. The final product of lateritisation of BIF and BIF-derived ores is typically complex, due to successive overprinting of earlier stages of alteration during the process, and because of the different precursors. This progressive lateritic modification tends to produce a varied surface complex including massive, vermiform, and botryoidal, or nodular aluminous/siliceous goethite and haematite, variously known as ferricrete, duricrust, canga, or 'hydrated zone hardcap'. The significant difference in these ores to the supergene mimetic martite-goethite ores is that they grow downward, with the total destruction of any of the parent BIF or BIF-ore textures.

Jan 1, 2009

In 1989 Henry Fairlie wrote a cover story for The New York Republic, 'Fear of Living'. He noted, `The first Apollo space craft caught fire during a test on the launch pad. Three astronauts were killed, the nation was shocked and horrified, all the more because the screams and scrambles of the astronauts could be clearly heard'. After a brief delay in manned flights, the Apollo program resumed with strong public support; within 18 months, Apollo 11 landed on the moon. Fairlie contrasts the Apollo tragedy to the 1986 Challenger disaster. `The prevailing mood in America so panicked NASA that it took almost three years to send up another shuttle', he observed. `In 19 years between these tragedies, the idea that our individual lives and the nation's life can and should be risk-free has grown to be an obsession threatening to create an unbuoyant and uninventive society.' Taking risks is a normal part of our daily routine. The act of living involves minute-by-minute decision-making focused on survival through the practical management of risks. The act of breathing exposes each individual to the risk of infection while the act of crossing the road could almost be considered suicidal. We deal with these constant threats by observing simple rules of hygiene, safety or what may be labelled as common sense. The rules of community, designed to minimise risk in society, can at times lose focus and result in the imposition of schemes that have a far greater cost than the issues from which they protect. Effective management of risk, whether in the community or a business is about awareness and balance and the elimination of unacceptable risk. Risk cannot be eliminated from our lives or our working environment. However it can be managed if it is properly understood, monitored and controlled. The purpose of my presentation today is not to provide a comprehensive technical risk inventory but to capture the essence of risk and the application of management strategies designed to deal with it in a positive fashion. The basis of our differential financial reward system is risk. The key to successful management is to deal with the downside risks in such a fashion that the benefits of enterprise are not eliminated. The key question any investor must consider is `can the major risks assQciated with a venture be managed or eliminated while retaining a greater proportion of upside potential'. The answer to this question is the ultimate value an investor would assign to any project. In reviewing the relevance of risk to our industry the range of papers to be presented today provide examples of how management deals with specific components of risk. In each case the value of the business has been enhanced by the practical application of balanced risk management. The ultimate success of the industry depends very much on this concept as it also provides a public showcase upon which we are judged. Therefore, from all perspectives the effective management of risk is a cornerstone from which to build a stable and progressive mining industry.

Jan 1, 1994

Distal rhyolitic tephras from the Taupo Volcanic Zone are widespread in the Auckland urban region. Some are primary air fall or flow deposits but most are reworked. Their presence indicates potential hazard for the Auckland urban region from future eruptions of central North Island volcanoes and associated secondary effects. Geotechnical problems occur as a result of weathering of the tephras yielding sensitive materials.

Jan 1, 1990

By Hu Y, Li D, Qu G

In this paper the structural mechanism of the gold - lixiviant complex is investigated. The results show that there are two common characteristics in the outer orbitals for all the gold lixiviants: a) a (Y -type of HOEO to form the L-*Au co-ordination bond, and b) a it type f LUEOs, with symmetry the same as that of 5d orbitals of Au, to form L

Jan 1, 1993