Search Documents

The outcome of future metallogenic research will be important to everyone because it will. have a profound impact on our ability to find new deposits of non-reservable mineral resources. Failure to replenish our mineral stocks will threaten man's economic and social well-being, and it is vital that future directions of metallogenic research are considered carefully to ensure that research funds are applied wisely to underwrite our future.Today we are witnessing the declining phase of the era of easy exploration. The rate of discovery of shallow orebodies is slowing. This is very evident for base-metal deposits but is becoming increasingly apparent for gold deposits. The easy exploration era was marked by a heavy reliance on exploration techniques capable of directly detecting mineralization. These include simple prospecting methods as well as a host of geochemical and geophysical procedures and tools that enable explorers to pin-point regions' of mineralization within the upper couple of hundred metres of the Earth's crust. The role of

Jan 1, 1990

By R Bresca, A McCallum, J Scealy

The Endeavor Mine, located to the north of Cobar, New South Wales, was purchased by CBH Resources Pty Ltd in September 2003. The operation has been producing lead and zinc concentrate continuously for over twenty-three years. In 2004, a water management program was instigated to improve the raw water use efficiency of the mining operation. The water management program involved the establishment of a Water Management Committee, a review and quantification of water use across the site, investigation and implementation of efficient water use practices, and workforce awareness training. The program has seen the amount of water used per tonne of ore milled reduced from an average of 1.08 kL/t in the March 2004 quarter, to 0.68 kL/t in the March 2005 quarter. This paper outlines the Endeavor Mine water management program and may serve as a model for other operations that are planning to improve their water use efficiency.

Jan 1, 2006

Owing to the 'creeps' and consequent movements in the mines, followed by the recent fire in the southern workings, the whole of the orebody above the 800 ft. level is now very much crushed and broken. The same applies to the hanging wall or overwall coutrny, which has subsided towards the workings, so that for some years past all development work within the lode has had to be carried out with extreme care.The continual but slow subsidence of the overburden into the stopes necessitates a periodical renewal of all gangways in the lode, and, as the subsidence amounts to as much as 60 ft. in places, these new gangways must necessarily pass through the mullock-filling of old stopes in addition to broken ore. They at times pass into the broken ground of the hanging-wall for some distance, where the orebody has widened underneath by the original folding and puckering.

Jan 1, 1932

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

By B P. Banerjee, D Patra, S Raval

Roof bolts are an essential component of roof support systems in underground mines. They are used to provide structural support to the roof of the mine and prevent it from collapsing. Therefore, it is imperative to perform regular assessments of these roof bolts to avert any hazards. Manual investigations of roof bolts are done by surveyors in underground mines, which is extremely timeconsuming and challenging due to the low-light conditions in underground mines accompanied by stringent mine access rules. To this end, automated recognition of roof bolts in 3D point cloud data obtained through laser scanning in underground mines serves as a potential solution to aid roof bolt monitoring. With the continuous advancements in laser scanning-based 3D data acquisition systems, the feasibility of making such surface estimations from 3D point cloud data has increased severalfold.

Sep 1, 2024

APPIN AND TOWER METHANE ENERGY PROJECTA world first in energy innovationBHP has teamed with Energy Developments Limited and Lend Lease Infrastructure, to establish an electrical power generation facility that utilizes methane produced as a by-product of mining at BHP's Appin and Tower coal mines in southern New South Wales.

Jan 1, 1998

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

By Browne TJ

On 13 October 1993, a shallow earthquake registering 7.1 on the Richter Scale occurred near Tauta in the Finisterre Range of Papua New Guinea (PNG) killing 37 people. The aftershock series lasted three months and resulted in considerable landslide damage that destroyed villages, food gardens and airstrips, and blocked rivers causing catastrophic flooding. These effects have irrevocably altered the form of many of the valleys and rivers draining into the Markham and Ramu valleys.The earthquake occurred in a pilot study area for a landslide hazard mapping project being carried out by the PNG Geological Survey that commen-ced in April 1993. Comparisons made between areas identified as unstable during the study with those damaged by the earthquakes show good correlation.It is concluded that aerial photograph and Landsat TM imagery interpretation can be used with a high degree of confidence to identify potential landslide hazards in mount-ainous terrain. Landslide hazard maps are promoted as a tool for use in the route planning of roads and powerline corridors, as well as for identifying vulnerable communities.

Jan 1, 1994

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

QEMSCAN« technology is a widely accepted automated e-beam technique providing quantitative and statistically robust mineralogical data to the mining industry. It uses X-ray mapping combined with backscattered electron (BSE) brightness to identify minerals in almost any type of geological material (Gottlieb et al, 2000). Besides the modal mineralogy also the liberation, associations, average grain size and other textural information can be obtained. The aim of this study is to test reproducibility of this technique by setting up and running standard tests on different QEMSCAN« systems. Multiple sample blocks were prepared by our standard operating procedure as epoxy-mounted, carbon-coated, polished blocks. The replicates were measured under the same conditions and measurement parameter settings on different QEMSCAN« instruments. The relative standard deviation (RSD) for the set of measurements was calculated. Generally the reproducibility of the systems themselves was found to be excellent, ranging between 0.4 and 1.5 per cent RSD. The more significant change in the reproducibility was found to be caused potentially by the sample preparation and variation in the mineralogy of the replicates. The measurement parameter settings together with these variations can account for almost 15 per cent RSD for minerals of low abundance. For analysed samples good results for the main phases present in quantities higher than 2 - 5 wt per cent of the total mass of the sample were confirmed with RSD generally below six per cent. Following the experiments, the parameters having the biggest influence on the performance of the QEMSCAN« and its precision are discussed in detail. The importance of sample preparation procedures and measurement parameter settings is emphasised. It is shown that experience and excellence is necessary for getting the most from the automatic mineralogical methods like QEMSCAN«.

Jan 1, 2008

In the last 100 years, statistical sampling theory for particulate materials has developed to a stage where sampling systems can be confidently designed to provide assay results of known and controlled variance for a chosen time period. The two independent sources of sampling variance, namely intrinsic and distributional heterogeneity are defined and explained quantitatively. Intrinsic heterogeneity is characterised by the sampling constant for the material and distributional heterogeneity is quantified by the process steam variogram or covariance function. The means by which sampling systems can be designed to an accuracy specification is described.

Jan 1, 2002

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

Unprecedented political, economic, and social change throughout the world will have an increasingly profound effect on the dynamics of the world's mining industry. Analysis of the early financial trends in this development (statistics on exploration expenditure, and investment flows) gives some insight into the magnitude of structural change and its implications for established mining economics and companies.Increasing confidence in the stability of many third world and developing countries is attracting exploration and investment capital that had previously been largely directed to established mining economies in North America, Australia, Europe and Southern Africa. Some of the projects requiring capital and technology in the CIS, Africa and Latin America are technically very attractive. The end of the 'cold war' and the influence of the IMF is gradually changing their risk profile for mining investment.

Jan 1, 1993

By Mountiney B

The development and operation of three large open cut brown coal mines in the Latrobe Valley, Victoria, Australia, requires a wide range of drilling techniques for coal resource evaluation and stratigraphic defi- nition, material property identification, open cut dewatering, and instal- lation of groundwater monitoring bores. This paper describes in detail the range of drilling techniques, equip- ment used and associated problems with drilling, in a deep sedimentary basin containing several major brown coal seams, multiple aquifer sys- tems of varying pressures and thin layers of hard materials including pyrite, siderite and basalt. Methods of rotary drilling include wireline core drilling, conventional core drilling, conventional flush drilling, diamond core drilling, reverse circulation air lift drilling and bucket auger drilling. Cable tool drilling is also used for strata definition and aquifer sampling.

Jan 1, 1989

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

By B S. S Rao, S Chandra

IndiaÆs iron ore mining industry is growing rapidly in order to augment the capacity to meet the unprecedented demand for the iron ore. Traditionally, much of Indian iron ore production came from exploitation of high-grade haematite ores, with the exception of Kudremukh which beneficiates lean grade Banded Magnetite Quartz ore. Now with the changed scenario of demand and supply, keeping long term sustainability in mind, it is imperative to develop suitable processing technology for exploitation of banded haematite quartz (BHQ) ore available abundantly and not utilised so far. In this direction detailed characterisation and beneficiation studies were conducted with BHQ iron ore from the Bellary-Hospet region of India, assaying 36.5 per cent Fe. The mineralogical studies with the image analyser system revealed the presence of maghemite and haematite as iron-bearing minerals. The gangue mineral associations were siliceous, ferro-magnesian and carbonate minerals. Higher degrees of liberation were observed in the size range of 75 - 212 microns. Liberation grind tests were performed by grinding the ore to different top sizes in a closed circuit laboratory ball mill with the ground samples subjected to Davis tube tests. The yield, grade and recovery were used as parameters to plan a two-stage wet drum magnetic separation based on grinding the primary magnetic concentrate. After subjecting the final magnetic concentrate to flotation to remove residual silica a concentrate assaying more than 68 per cent was obtained. The non-magnetic product from the primary magnetic separation was deslimed, ground, blended with secondary magnetic tails and was subjected to a two pass wet high intensity magnetic separation (WHIMS). The WHIMS concentrate was further subjected to two-stage flotation to remove residual silica to obtain concentrates assaying 64 - 66 per cent Fe. The final combined concentrate from wet drum magnet and WHIMS after flotation could yield a blast furnace (BF) grade pellet feed concentrate assaying more than 65 per cent Fe with a yield about 39 per cent and iron recovery about 70 per cent. A direct reduction (DR) grade pellet feed concentrate assaying 67 per cent Fe with a yield of about 28 - 31 per cent and iron recovery about 53 - 57 per cent could also be produced. Based on the test work, a process flow sheet was developed to beneficiate the BHQ ore for production of BF/DR grade pellet feed concentrate. In this paper methodology adopted for selection of individual process, various diagnostic tests performed to rule out other beneficiation processes and the final process flow sheet development is presented and discussed in detail.

Jan 1, 2007