Search Documents

By Kennedy G. L

Operating experience with the pilot Lurgi carbonization plant at Morwell showed that under conventional operating conditions, although the thermal efficiency of the plant was very' high, the physical quality of the char produced was extremely poor. By variation of operating conditions to produce the slow drying rate developed by the laboratory research at the University of Melbourne, an improvement in the size of the char was achieved. A similar approach in the carbonization stage where severe breakage of the briquettes still occurred was not possible due to insufficient control over the heating in this stage. Theoretical analysis of the heat exchange process has shown that severe heating of the briquettes entering the carbonizer is a characteristic of the Lurgi system and cannot be controlled by modified operation. The plant has been closed down for reconstruction of the heating system to enable it to be used to produce hard char.INTRODUCTIONAn experimental carbonization plant was operated at the Morwell Works of the 'Gas and Fuel Corporation from November 1958 until July 1959. This plant was built as a pilot plant by the Corporation to designs supplied by the Lurgi Gesellschaft fur Warmetechnik and had the nominal capacity to carbonize 25 tons of brown coal briquettes and to produce 11 tons of char per day. The briquettes were supplied from the· normal production of the Yallourn briquette factory and the 2t in. I-type briquette was the largest size which the plant could handle.This carbonization plant represents the intermediate stage of development between the laboratory research at the University of Melbourne and the commercial production of hard char as a metallurgical fuel. It is intended in the first place for the study of the technical problems in the handling and...

Jan 1, 1960

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

Some 800 analyses for Cu, Zn, Pb, Ag, Fe, S, CaO, MgO, C02, Si02 and Al203 were used to examine the elemental constitution of the Mount Isa ores, and, for comparison, those of the Northern Leases area.Lead: zinc relations show little order from sample to sample, but means of large zones (Le. individual orebodies) show a highly linear inverse relationship. Lead: silver ratios are fairly constant from sample to sample, and means show a highly linear direct relationship.Sulphide sulphur appears to be related to carbonate and alumina abundance, sulphur decreasing systematically with increase in the ratio CO2:AI203. In all graphs involving members of the group CO2-A203-S the lead-zinc and copper ores conform to the same simple trends, confirming that the two ore types and their host rocks are genetically closely related. The earlier deduction of a volcanic-sedimentary origin for the sulphides of the Black Star orebodies appears compatible with present findings.On the basis of such an origin, the pattern of sulphide occurrence and mineralogy in the Mount Isa district is possibly related to the configuration f the upper surface of the "Eastern Creek Volcanics", the facies patterns of the overlying sedimentary rocks, and to the oldest faults affecting the two.INTRODUCTIONStanton (1962) described and interpreted the chemical constitution of the Black Star No. 2 lead-zinc and the 650750 copper orebodies at Mount Isa. The investigation has now been extended to the other principal orebodies of the area.The earlier study showed that the host rocks of the two adjacent Black Star orebodies were constitutionally closely related, and suggested that this was probably due to their original formation in contiguous zones of sedimentation. On this basis the silica-dolomite of the copper ore appeared to represent the slightly more shoreward, "limey" member, probably a fairly massive algal calcareous sediment laid...

Jan 1, 1963

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981

By M Lentz

This paper will discuss the issues associated with blasting in an urban mining environment that have been addressed by Winstone Aggregates at the Mt Wellington Quarry. These issues include - control of vibration and air overpressure, repeatability of shot performance, fragmentation on an extremely low maximum instantaneous charge, compliance with Territorial Authority regulations and perception. Over the last two years, in order to address these issues, Winstone Aggregates have undertaken a programme of continuous improvement, which has included; ò implementation of new technology; ò revising site procedures; ò conducting an investigation into the structural response of local buildings; ò investigating safe extrapolation; ò extensive public consultation; ò establishing credibility during the consent process; ò identification of perception issues; and ò building relationships and trust with neighbours. The issues addressed at the Mt Wellington Quarry have increasing significance for traditionally rural mining operations, as the input of the local community being urban or rural, increases. New and existing operations have the potential to adopt best practice now, building trust with the community and raising the profile of the industry.  

Jan 1, 1999

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By Olliver J. G

Over 400,000 tonnes of kaolin, sillimanite, mica, kyanite, feldspar and rutile have been mined from the unique Williamstown orebodies since their discovery in the early 1900's. Numerous companies; both large and small were associated with the early development of these deposits but since the formation of Australian Industrial Minerals in 1947, this company has been the only significant producer. A combination of mining and management problems almost forced closure of the mine in the late 1970's but this was averted by a changed attitude towards mine planning. Mine development is now based on detailed geological and technical investigations, exploration for additional ore reserves is being conducted and laboratory and pilot scale studies are being undertaken to utilise both low grade ores and waste materials. The professional approach to mine and market development will ensure that Williamstown mineral products will continue to be available for many years.

Jan 1, 1989

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Greymouth Coal Project is a proposal to mine by the application of proven hydraulic, and room and pillar underground mining methods; and to process the equivalent of an average of 1.7 million tonnes per year over a forty-year period. The proposed mine site is located ten kilometres north of Greymouth, on the west coast of the South Island of New Zealand. Of the three separate mineable seam groups, the thick Main Seam Group, which makes up 77% of the total resource, will be mined by hydraulic mining technology.   It is proposed to market and produce a high volatile bituminous type coal with low ash (6%) and sulphur (0.4%). Because the inherent ash content is low, the requirement for coal treatment will only be the use of a single cell jig circuit to control the effects of rock dilution and partings. The resulting coal product is tentatively planned to be transported by rail to the port at Lyttelton for loading on to Panamax or Post Panamax size vessels.

Jan 1, 1997

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S M Richardson, A W McNeill, J B. Gemmell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Hellyer, Fossey, Que River and Mount Charter volcanic-hosted massive sulfide (VHMS) deposits occur within the Que-Hellyer volcanics of the Mount Read volcanics, Tasmania. These deposits occur along a 6 km strike length and are hosted by the same stratigraphic unit. We use a combination of whole-rock geochemistry, short wavelength infrared (SWIR) spectrometry, laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses and compiled historic whole-rock geochemical data to develop district-scale vectors towards VHMS mineralisation.Strongly sericite and K-feldspar altered rocks concentrate along a linear trend from Hellyer, through Que River, to Mount Charter. Ishikawa alteration index values and whole-rock major and trace element concentrations provide exploration vectors towards mineralisation on a regional scale as significant enrichment and depletion trends. On a deposit scale, composition variations in white mica (sericite alteration), chlorite and K-feldspar are observed and reflected in whole-rock geochemical variations. Regional SWIR data from drill core support the prevalence of phengitic mica and high-Mg chlorite within footwall alteration halos and highlight the main upflow zones of hydrothermal fluids in the VHMS district. The combined use of regional whole-rock geochemistry, SWIR and mineral chemistry is an effective way to highlight prospective areas for VHMS mineralisation in a mature exploration province.CITATION:Wu, S, Gemmell, J B, McNeill, A W and Richardson, S M, 2015. Exploration implications from variations in whole-rock and mineral chemistry around the volcanic-hosted massive sulfide deposits of the Que-Hellyer volcanics, Tasmania, Australia , in Proceedings PACRIM 2015 Congress, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

By D Smith, A Ramdhani, J Francke

Ground penetrating radar (GPR), a well-established geophysical technique generally used for shallow civil engineering applications, has, in the last decade, found increasing acceptance as a complementary tool in mineral resource evaluations. As new sites are trialled with the method, a greater understanding is being garnered regarding the most suitable environments for long-range radar. Although successful projects have been conducted worldwide for mineral sands, iron ore and alluvial projects – tropical weathering environments have produced some of the most impressive results. Specifically, tropical nickel laterites have shown to be, with some notable exceptions, ideal GPR environments.Such high-resolution remote sensing has particular relevance to bulk commodities or those which possess significant rheological variation within geological units, and has led to some innovative downstream uses within exploration, project development and the larger mining industry. In this paper, we examine the application of long-range GPR in Indonesian nickel laterite deposits in general, to highlight some of these novel applications with particular reference to resource modelling, mine geology and operational economic implications.CITATION:Francke, J, Smith, D and Ramdhani, A, 2014. Ground penetrating radar to enhance the exploration-to-mining value chain, in Proceedings Ninth International Mining Geology Conference 2014 , pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930

A calibration of the Frantz isodynamic magnetic separator relates the current in the electromagnet and the transverse slope of the chute to the specific susceptibility at which separation is being effected. In addition to providing a rapid measure of the specific susceptibility of minerals and composite grains, the calibration provides a guide to operation of the Frantz isodynamic separator for mineral separation, and to the nature of composite grains. The most sensitive magnetic separation is obtained by using the highest practicable current and transverse slope, and the lowest practicable longitudinal slope.INTRODUCTIONProbably all minerals have a magnetic susceptibility measurable by sensitive techniques. However, magnetic separation between minerals which have low but different specific susceptibilities, and which for many purposes are considered essentially non-magnetic, has only become practicable with the development of the Frantz isodynamic separator.The construction and principle of this highly sensitive separator has been described by S. G. Frantz as an appendix to a description by 'Gaudin and Spedden (1943) of its application to the separation of sulphides constituting mill products.Various publications (e.g. Hess, 1949, Hutton, 1952) refer to its use in separating the mineral constituents of rocks, ores, and unconsolidated sands.As used in this study the Frantz isodynamic separator consists of a vibrating chute mounted centrally between the pole pieces of an electromagnet (Fig. 1). This unit may be inclined in any direction by the universal mounting, and the electromagnet current is continuously adjustable from 0 to 1·5 amperes.

Jan 1, 1957

By E V. Kislov

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Northern Baikal Ni-Cu province is located in Buryatia, south-east Siberia, and geologically is part of the Baikal-Muya volcano-plutonic belt. It is known for numerous PGE-Ni-Cu-bearing mafic-ultramafic intrusions of Neoproterozoic age formed in various geodynamic settings. All these deposits can be regarded as a single Ni-Cu ore cluster located near the Kholodninskoe Pb-Zn deposit, which is ready for mining. In addition, there are less studied, small dyke-like bodies with sulfide mineralisation that formed in a rift setting and may be enriched in Ni, Cu and PGE. Individually, the known bodies are of poor commercial value by their resources, but their close spatial association (<30 km) may make these PGE-Ni-Cu deposits economic in the future. This extended abstract seeks to provide a geological framework of the North Baikal Ni-Cu-PGE province, specifically at the north-eastern Synnyr rift hosting numerous small subvolcanic bodies with Ni-Cu sulfide mineralisation. Some small subvolcanic bodies contain industrial level Ni-Cu deposits (Shanuch, Cabanga-Musongati, Voisey’s Bay, Jinchuan, etc).CITATION:Kislov, E V, 2015. North Baikal region Ni-Cu deposits , in Proceedings PACRIM 2015 Congress, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015