Search Documents

By Patridge A. C

Hydrocyclones have widespread use as classifiers in applications such as mine fill preparation and coal preparation. A fundamental conflict often exists between recovery of all of the valuable material and maintaining the quality of the product. This conflict is a result of a portion of the feed material passing through the cyclone, effectively without undergoing any classification. This paper describes an investigation, undertaken as an undergraduate project in mining engineering at the University of NSW (Brook, 1994), into aspects of cyclones in which supplementary water injection is used in an attempt to reduce the amount of misplaced fine material reporting to the coarse product and hence improve the overall classification efficiency. In particular, the study concentrated on the effects of different modes of water injection. Two methods of introducing wash water into the cyclone body were investigated. A series of tests were performed on a laboratory hydrocyclone having provision for radial water injection at different levels through small orifices in the wall of the conical section, and a preliminary study was made of the performance of a novel cyclone in which the conical section had walls of a permeable polyethylene, permitting a uniform introduction of wash water over the entire surface.

Jan 1, 1995

By Kupper T

Firstly, electric analog models are discus- sed to show fluid streaming conditions. In these models the depth of blast at tuyere level, the height of the bath, the influ- ence of different angles of the furnace zones and the different possibilities of the root of the cohesive zone have been changed. Tests to define the influence at a large blast furnace are given. Secondly, the wear of carbon bricks in the hearth is examined under the influence of gas, slag and pig iron. Oxidation tests in a special scanning microscope with the pos- sibility of heating and gas treatment are shown. Wear mechanisms are discussed fora large blast furnace and proposals for im- provement are given. Finally, the possib- ilities and value of the temperature meas- urement in the hearth block are discussed.

Jan 1, 1981

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005

In Australia a social impact assessment (SIA) is generally required prior to the approval of a mineral resource extraction or processing projects as a part of the Environmental Impact Assessment (EIA) process. In recent years there has been increased attention on the adequacy of the SIA process applied in major project assessment. Most applications have focused on the impact identification process with little attempt given to the community negotiating power over how impacts will be addressed. The impact assessment tends to occur at a single point in time, with no subsequent re-evaluation or ongoing social impact management and monitoring process. The assessments rarely specify how responsibilities for impacts on communities may be apportioned between project proponents and government, and have been inadequate in dealing with cumulative project impacts. In Queensland, concern about these shortfalls have led to the release of the Sustainable Resource Communities Policy 2008 and requirements for social impact management plans (SIMP) to be developed for each resource development in the State. In this paper a 'pressure-state-response' approach to impact assessment is used to develop an 'impact-response-monitoring-evaluation' (IRME) framework that can be applied to ongoing evaluation and monitoring of social impacts. The framework is applied to coal resource developments in the northern Bowen Basin in Queensland to identify core requirements in a SIMP. The IRME framework is flexible enough to be implemented at various spatial and time scales, for the wellbeing of the local and regional mining and non-mining communities in Australia. The framework can be further examined in other mine developments and could be integrated with the existing mining or environmental protection acts.

Jun 1, 2010

Australia is a highly significant hub in the global minerals business. This paper will present the results of global and national studies looking at the potential 20 to 30 year future evolution of the mining and metals industry.   Globally, the World Economic Forum launched a Mining and Metals Scenarios project in January 2009 to explore the question: 'How will the environment for the global mining and metals industry look in 2030?'. As part of a structured strategic foresight process, eight workshops were held across the world over the course of a year which brought together over 200 leaders from the private sector, government, academia and non-governmental organisations. The workshops were supplemented by personal interviews and guided by an international advisory board.   Critical uncertainties for the future of the industry were identified and compare extremely well with the outcomes of a national survey of AusIMM members identifying the key issues and drivers shaping the future of their operations. Global context was one of the most significant issues identified by The AusIMM membership, which is expanded in the World Economic Forum study in terms of: geopolitics; global governance; action on climate change; and economic outlook. More specifically, this global study developed three divergent yet plausible scenarios describing potential environments for the global metals and mining industry in 2030. These scenarios are compared with ground-breaking global foresight work coordinated by the Stockholm Environment Institute in the 1990s. The scenarios will help decision makers rehearse alternative futures, anticipate potential hazards and identify business opportunities - new solutions, new markets and new connections. The presentation will present these scenarios as a way of challenging thinking, testing established wisdom, and stimulating imagination about the business case for the mine of the future. As Marcel Proust put it, 'The real voyage of discovery consists not in seeking new landscapes but in having new eyes'. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By Peng SS

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

Host minerals for gold have been of great interest to exploration geologists and metallurgists for a variety of reasons. The depletion of high grade ores in many parts of the world requires that greater attention be given to the study of host min-erals for gold. Some host minerals have been employed in exploration as traces for gold. They are also essential in the design of extraction processes for treating gold ores.This paper reviews the mineralogy of important gold deposits of Papua New Guinea (PNG), Indonesia and New Zealand and focuses attention on the ore minerals and rock-forming minerals that host gold.

Jan 1, 1994

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

The Australian Constitution specifies certain powers of the Commonwealth Government to be used in its capacity as the national government. Certain of these broad powers result in the Com- monwealth having a facility to play an important part in the development of the mining industry. The State Governments, however, by virtue of their wide powers to regulate matters within the boundaries of a particular State, are more directly involved in the day to day administration and standards of activities of mining operations. In this respect the Common- wealth has something of a dual role because of its "State-like" responsibilities for the mainland Terri- tories. The components of the role that the Common- wealth Government discharges in relation to the mining industry are qualified to varying extents at particular times by the political persuasion of the Government. In absolute terms the components are as follows. 1. Economic management. The Commonwealth's fiscal and monetary policies have an important effect on industry as well as on State finances. In particular, the taxation regime employed by the Commonwealth Government is of direct importance to economic decision-makers in the mining industry. 2. International matters. International trade and commodity matters are, more and more, becoming an everyday part of the conduct of a nation's foreign affairs. 3. Exports. The Commonwealth Government, via the constitutional powers over overseas trade, have exercised varying degrees of control over mineral exports to achieve particular objectives. 4. Foreign capital and investment. Australia in general, and the mining industry in particular, is and will continue to be a net importer of capital. There appears to be bipartisan political agreement in Australia that foreign investment policy must be enunciated to ensure that investors. are in no doubt that Australia welcomes beneficial investment and technology from overseas. 5. Environment and Aborigines. Governments, both Commonwealth and State, have in recent years become more involved in these areas in response to their interpretations of community aspirations. 6. Energy. Access to assured supplies of energy is now viewed, by Governments worldwide, as a desirable asset to ensure the well-being of a nation's people and industries.

Jan 1, 1978

By K Baker, J Purtill

One of the key challenges for the mining industry globally is the rehabilitation of mine waste, and Queensland is no exception. Out of pit waste structures including waste rock dumps and tailings storage facilities, create novel landforms which require ongoing maintenance and pose risks to the environment and sometimes to communities. Where multiple mines co-exist, such as parts of Queensland’s Bowen Basin, individual mines can often be constrained by adjoining operations. This presents opportunities for broader rehabilitation strategies to be considered, more than the current single mine focus, that may provide better environmental outcomes for a region. Given recent global disasters involving tailings storage facilities, and our team’s endeavours to drive Queensland to achieve leading practice in mined land rehabilitation, we are exploring the potential to maximise in-pit tailings disposal opportunities for coalmines through shared waste management strategies. A shared waste management strategy is where two (or more) mines, owned by different companies and operated under different environmental permits, transport tailings from one mine to the other in close proximity, for disposal in a disused pit. This would reduce the number of waste structures to be built, operated, rehabilitated, and managed in perpetuity. Our objectives are to identify and remove barriers to tailings transfers between sites to:  minimise environmental risk  minimise long-term liability of managing mining waste and associated structures  support improved outcomes for the local community. To determine the scale of coal waste disposal practices in Queensland, internal data and publicly available imagery was analysed by the Department of Environment and Science in 2022. Approximately 6500 ha of land in Queensland is utilised for coalmine tailings storage facilities or codisposal areas, with ≈ 3700 ha of this being out of pit.

Aug 2, 2023

The central thickened discharge system of tailings disposal takes advantage of the natural beach slope formed by sub-aerially discharged tailings, and the non-segregating properties of thickened tailings, to create a homogeneous conical stack. The need for containing embankments can be largely avoided leading to capital and operating cost savings. Methods for estimating beach slopes and tailings density, essential parameters for the design of such a system, are described. Case histories from three mining operations are used to illustrate the application of the technique, There are also seen to be potential advantages in the areas of water management, seepage, and rehabilitation. Laboratory and in-situ testing enable parameters to be determined.

Jan 1, 1991

With constantly rising energy costs it is ever more important that we look at ways of im- proving comminution efficiency both in terms of power consumed as well as capital costs required for purchasing and installing equipment. I intend to show that commonly used appli- cation criteria, which is presently accepted for designing crushing and screening plants, need drastic revision if it is to be used to accura- tely design, predict and refine performance in new and existing facilities. Unless we can calculate performance accurately, we cannot minimise capital investment and maximize Profitability.

Jan 1, 1978

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011

By Grantham DL

ABS'TRACT For a number of years research efforts have been directed towards improving the efficiency of sampling and analysing coal mine roadway dusts. In the past decade the practicality of rapid, on site analysis of the incombustible content of these dusts using a radioactive technique has been receiving close attention both in Australia and overseas. Accurate measurement of the total incombustibles present is only possible by time consuming chemical methods. As the densities of the solid incombustible materials are greater than that of coal, they absorb a higher proportion of incident low energy gamma radiation than does coal. The amount of such radiation "back scattered" from mine dust samples is therefore inversely related to their average densities, and hence to their incombustible contents. This phenomenon can be used as a measure of incombustible content by employing an appropriately designed and calibrated instrument.

Jan 1, 1981

The Tick Hill Gold Mine is situated approximately 110 kilometres south of Mount Isa, and 14 kilometres north of the township of The Monument. It was discovered in October 1989 by Mount Isa Mines Exploration in an area which had been targeted as high in potential for copper-gold mineralization.A mining lease application was made in March 1990. Mining, and the construction of the plant and infrastructure, began'in early August 1991 after the lease was granted on 20 June of that year. Commissioning of the plant began in December 1991, and the first gold was poured on site on 31 December 1991.The development of the underground mining operation commenced in January 1992 with the drilling of the ventilation shaft. The access decline was started in March of the same year, with the first ore produced from underground in August.

Jan 1, 1993

By Cook B, Cunningham J

At Mount Isa Mines, a system has been developed for general monitoring of underground mobile equipment. It can provide unit condition monitoring data such as oil pressures and motor temperatures as well as production type information such as unit location and load. The system does not rely on an expensive data communications infrastructure, using instead inexpensive radio base stations which automatically transfer data from mobile units to a surface database server on the company-wide computer network. This paper includes a general overview of the system and a discussion of the practical benefits it is expected to generate.

Jan 1, 1995