Search Documents

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

A system for rapid on-line determination of weight percentage coal in slurry and weight percentage ash in coal has been developed at the Julius Kruttschnitt Mineral Research Centre, University of Queensland. The gauging system is suitable for use with coal flotation slurries or slurries having a maximum particle size of about 1 millimeter. The system is based upon measurement of gamma ray transmission; radioisotope sources emitting photons of two widely different energies are employed. The inaccuracies of measurement that would normally result from variable amounts of air entrained in the slurry are substantially reduced by pressurising the slurry to approximately 2MPa (300 psi) using a Mono pump. The equipment can be used to make measurements on more than one slurry stream by pumping streams sequent- ially. The system is being tested at the Peak Downs Mine of the Utah Development Company in Central Queensland. This paper describes the theoretical principles of the gauge design, the experience gained to date in the commissioning of the equipment, including the installation of a PDP 11/03 computer, and the progress made in developing satisfactory interpretations of the gauge count-rate output.

Jan 1, 1978

Proceeding from statistical data on the development of waste volume, an endeavour was made to characterise waste materials with regard to the applicability of treatments based on mineral processing. Many types of waste are characterised by a high heterogeneity. The separation processes used for processing raw minerals can also be used for separation of various waste mixtures. For some waste mixtures, differences in properties can be utilised for separation which are mostly less distinctive for raw minerals. State-of-the-art technology is illustrated with selected Examples.

Jan 1, 1993

This paper considers two particular empi- rical models for the processes of the generati- on of hydrochemical zoning and epithermal near- surface mineralization of mercury-antimony-arse- nic formation in the discharge area of the Uzon Caldera ore generating hydrothermal system in Kamchatka. Vertical and horizontal hydrochemical zo- ning is caused by mixture of infiltration waters of the surface formation with fluid of chloride- sodium composition which are supplied up the-zo- ne of deep fault. Ore formation is caused by simultaneous existence of two geochemical barriers, namely oxidizing and reductive. The first barrier is determined by the-level of ground waters. The second one forms under the clay-opal screen un- der the influence of two factors, namely the inflow of deep reduction sulphur compounds (which are transported together with arsenic, antimony and mercury) and the generation of hyd- rogen sulphide as a result of sulphur- and sul- phate reduction. X-ray-amorphous phase of orpi- ment composition and realgar phase are formed, respectively, on the oxidizing and reductive Barriers.

Jan 1, 1987

By Stanton G

The Department of Mapping and Surveying (DMS), the Australian Key Centre in Land Information Studies (AKCLIS), the Department of Industry Development (DID) and the State Government Computer Centre (SGCC) are testing a regional information network in northern Queensland. Several study sites have been chosen by different groups of participants. The members of each common-interest group share their data for the site. They can also access datasets supplied by other organisations that are not directly involved in the particular study being undertaken. The participants include state government departments, local authorities, fed- eral organisations and the private sector. The participants communicate with computer systems in Brisbane via Q-Net. Q-Net is a pilot State government tele- communications network, established by the Department of Industry Development. Q-Net uses the communications sat- ellite AUSSAT 1 as the primary instrument of data transfer. The Q-Net network is a star system, with a Master Earth Station in Brisbane acting as a hub for radial earth stations, located throughout Queensland.

Jan 1, 1987

By Bailey S, Avraamides J

Laboratory-scale experiments were conducted in a mechanically stirred aeration vessel to determine the rusting abilities of aerated water in the presence of various catalysts compared to the industrially used ammonium chloride. The catalysts used were tartaric acid and citric acid, firstly by themselves, and then in later experiments mixed with ammonium chloride. From these experiments it was found that leaching of iron from reduced ilmenite in the presence of either tartaric acid or its sodium salt was much slower than in the presence of ammonium chloride. Citric acid or its sodium salt also give a slower rate of leaching than the ammonium chloride system, but citric acid and its sodium salt mixed in equal proportions produced a rate of leaching approximately twice as fast as the standard ammonium chloride system. When tartaric acid was mixed with ammonium chloride the leaching rate was found to be equivalent to the leaching rate of the same amount of ammonium chloride alone, thus indicating that tartaric acid made no contribution to the leaching in this svstem_

Jan 1, 1996

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995

By Bhattacherjee A, Makesh S

Mechanised sub-level stoping is one of the most widely accepted stoping practices followed in base metal mines in India. As a general practice, blast-scheduling of rings in these stopes is done either heuristically or randomly which leads to a high fluctuation in ore grade when drawn and delivered to the mill. In this paper, dynamic programming has been investigated as an optimisation technique for optimal blast-scheduling of rings. A microcomputer based dynamic programming algorithm has been developed in C language which runs under the UNIX environment. A case study based on Indian mine data is presented to demonstrate the application of the dynamic programming concept and use of the developed software. It is concluded that dynamic programming can be used as a production planning tool in Indian mines practicing sub-level stoping and following heuristic/random approaches for blast-scheduling of rings.

Jan 1, 1995

By T J. Beardsmore, N Wyche, D Flint, T J. Griffin

Western Australia (WA) is currently the world’s largest iron ore producer, and mining of its huge reserves and resources of iron ore has become a critical part of the state’s economy and regional development. Iron ore exports from WA have reached 760 Mt/a, corresponding to shipping more than one Mt per turn-of-the-tide from the state’s ports. The iron ore sector dominates all commodities produced in WA, and in 2016 accounted for 77 per cent of the state’s royalty receipts, 56 per cent of mineral and petroleum exports (by value) and 50 per cent of mining industry employment. Expenditure on exploration for iron ore (including that for resource estimation and conversion to ore reserves) has declined markedly, from its record peak of $1100 M in 2012 to $280 M in 2016, placing it second after gold. Foreign investment has been a key element underpinning development of the iron ore industry from the 1960s until today, and will likely continue to be so into the future.CITATION:Flint, D, Wyche, N, Beardsmore, T J and Griffin, T J, 2017. The importance of iron ore to Western Australia’s economy, in Proceedings Iron Ore 2017, pp 7–12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Chaves AP

This paper describes an investigation on the surface properties and mechanisms involved in the agglomeration of iron ore. For this purpose, an organic binder (carboxyl-methyl-cellulose (CMC)) was used in substitution of bentonite, the classic binder in iron ore concentrate agglomeration. Recently, a renewed interest of the iron ore producers in Brazil to replace bentonite for an organic binder, because of the economy that can be achieved in the, blast furnace operation. These savings are mainly due to the lower aluminum silicate addition which decreases slag volume and the improved pellet metallurgical properties which have the potential for lowering hot-metal production costs. Also organic binders are effective at lower addition levels, which results in lower storage and transportation costs. It is very important in Brazil because of the vast geographical area since transportation is made mainly by truck. Another advantage of organic binders is that they have low ash contents, and therefore most of the binders bum. off during the pellet firing operation. Previous studies have demonstrated the possibilities of the use of CIVIC, but in addition to its high cost, the pellets presented improper behavior at high temperatures or when prepared with high moisture levels. In the investigation here described, these problems have been solved through the addition of other reagents to CMC.

Jan 1, 1993

By Motyka J, Adamczyk AF, Witczak S

A case study of migration of a paper factory fluid wastes, on the distance of 5 km from an underground disposal site to an ore mine is presented. The ore mine in question, situated in SW Poland is pumping 3.5 m3/s (ca 300 000 m3/day) of groundwater, producing a cone of depression about 150 m deep and several kilometers wide. The migration of wastes (pollutant) occurs within the carbonate karstic aquifer of Triassic age. The aquifer is about 100m thick and is characterized by the coefficient of hydraulic conductivity equal to 8 m/day on the average. The results of systematic measurements carried out for 13 years enabled to estimate the mean breakthrough curve of the pollutant. On this basis and taking into account the coefficient of hydraulic conductivity as well as the mean hydraulic gradient between the disposal site and the ore mine, the migration parameters of the polluting material, i.e. the real flow velocity, the effective porosity and the longitudinal disper- sivity have been calculated. As the measurements considered a long migration distance of the pollutant, the obtained hydrodynamic dispersion constant (dispersivity), in the authors opinion, is reliable enough to be applied for regional groundwater calculations, regardless of the "scale effect".

Jan 1, 1988

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987

Copper grades of diamond drill hole and development samples are determined in the core shed logging area at Mount Isa Mine using a Bulk Mineral Analyser. All geological and grade data on the copper orebodies is collected and stored on computer file.The raw data can be manipulated interactively using a computer terminal or by input of forms to produce output as computer plots or printouts. Grade distribution of copper or cobalt is obtained by the geologist using a computer kriging package followed by grade contouring. Computer plotted cross-sections and plans of individual stopes or several stopes can be produced showing geological structures, kriged grades at points and as grade contours.

Jan 1, 1985

During induration of iron ore pellets produced from magnetite concentrates, there are many reactions occurring simultaneously. While the magnetite is being oxidised to hematite, carbonate fluxes are being calcined, leading to the formation of complex oxides. Calcination of fluxes and the formation of calcium and magnesium ferrites and silicates during the preheat stage can influence the magnetite oxidation process. As the calcination reaction proceeds quicker than oxidation at temperatures experienced during the preheat stage (700 - 1200¦C), the bulk flow of CO2 emanating from within the pellet should disrupt the diffusion of O2 to the magnetite reaction as the gas fluxes are similar in magnitude. This increases the time required for the oxidation of the pellet. Using an infrared rapid heating furnace, experiments were performed on heating individual magnetite green balls in an air atmosphere. These experiments showed that time played an important role in the extent of oxidation and calcination and temperature significantly influenced the initial evolution of high temperature phases such as magnesioferrite, calcium ferrites and calcium silicates. Understanding the kinetics of all these reactions for a particular pellet feed, and their interaction, is important for optimising the design of the induration furnace.

Jan 1, 2005

By Nichol R

- PART A The Hoppers Crossing Pumping Station is one of the principal components of the Western Trunk Sewer Project which replaces the 90 year old Main Outfall Sewer and will convey 60% of Melbourne's sewage flow from Brooklyn to the Board's Farm at

Jan 1, 1987

By Y Wu, F-J Ping

Today, coal production accounts for about 65 per cent of the nationÆs gross energy in China. By the year 2010, the output of coal is planned to increase to 1.65 billion tonnes and by the year 2020 to 1.9 - 2.0 billion tonnes. To meet these energy needs the Chinese coal industry is developing underground coal production on a massive scale. The new drive introduced by using direct torque control (DTC) is now proven technology for mine shaft hoisting. The drive offers unequalled speed and torque control performance as well as a low impact on the supply network by controlling the power factor to unity with a minimum of harmonics distortion.

Jan 1, 2005

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By Drain P, Dibdin T. R

THE completion of the Linda incline man and supply haft at the Mount Morgan Gold Mining Oompany's mine led to an investigation of the various safety gears in general use in mining shafts. One of these gears completely fulfilled the necessaryconditions. This paper endeavours to give a description of the man car and safety gears now operating in the before mentioned shaft, together with the main considerations leading to their design and sub equent adoption. Fig 1 diagramatically shows a longitudinal section of this shaft.

Jan 1, 1911

A contract for three 20 ft diameter vertically mounted axial flow fans of the same aerodynamic design, was placed by Mount ]sa Mines Limited in 1963. The hydraulic blade pitch changing mechanism, the method of blade fabrication, and the roll out centre casings are features of these fans. Protection devices and fan control are designed for unattended operation and remote control. The erection and commissioning of the fans during 1964-65 is described.

Jan 1, 1967

An ongoing research program into surface subsidence over Room and Pillar coal mining is described. A subsidence monitoring network has been established for one Room and Pillar mine in the West Moreton Coal Field of South East Queensland, at which pillar extraction is being conducted. The maximum measured subsidence to 28 January 1986 was 638 mm, with movement continuing. Analysis of the monitoring data with view to application of the subsidence pre- diction theory developed by Kowalczyk (1972) is discussed. The Kowalczyk theory provides predictions of subsidence depression, slope of surface, horizontal displacement, surface curvature and horizontal strain, for both the Partial and Total Settlement cases. The development of subsidence with time is also investigated and a preliminary analysis conducted.

Jan 1, 1986