Search Documents

By A Van den Bulck, K Verbeken, O Vergote, I Bellemans

Viscosity is one of the most important physicochemical properties during pyrometallurgical operations. In the sub-liquidus regime, an important factor is the presence of suspended solid particles, yet its influence is not well-described in earlier literature, despite the significance of this factor. This project aims to determine the influence of spinel particles (Zn(Al,Fe)2O4) on the rheology of a multiphase synthetic PbO-SiO2-ZnO-Fe2O3-CaO-Al2O3 slag system. Three data sets with a wellcontrolled methodology and three different spinel sizes (small (13 μm), medium (34 μm) and large particles (76 μm)) were published previously, using a custom-built high-temperature rheometer. This study presents an additional data set of slag viscosity measurements, performed using a different apparatus, the Anton Paar FRS 1800, to verify the consistency of the earlier determined viscosity behaviour. Within this data set, no consistent trend could be found between the predicted wt per cent spinel and the relative viscosity. Therefore, additional quenching experiments were conducted to identify the morphology and experimentally determined volume fraction of the spinel particles in the slag. These measurements revealed a difference in spinel size across the samples and corresponding viscosity behaviour, emphasizing the importance of spinel particle size on slag viscosity. Once the spinel size was taken into account, consistent viscosity results (relative apparent viscosity and flow index) were observed across the two devices. This study confirms that, once all parameters affecting slag viscosity are considered, the viscosity behaviour of a heterogeneous slag can be uniquely determined. The resulting optimised slag viscosity models can be used to predict viscosity before processing, addressing relevant phenomena such as slag tapping, slag foaming and copper droplet settlement.

Aug 21, 2024

By G Baird, M Seto

A low-cost methodology that allows the determination of in situ stresses using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the Acoustic Emission and Deformation Rate Analysis methods with those estimated by conventional Hollow Inclusion cell measurements. The studies have been focused on full stress tensor determination from a single oriented rock core. In all cases the rock core specimens recollected the in situ stresses reasonably well compared with the standard overcoring method.

Jan 1, 2000

By P Trotta

The majority of water to the Olympic Dam mine and the nearby townships of Roxby Downs and Andamooka is supplied from the Great Artesian Basin (GAB). There are no permanent local water sources available to Olympic Dam. The use of water from the Great Artesian Basin by Olympic Dam receives considerable attention by BHP Billiton and is extensively regulated by the Government of South Australia. Olympic Dam has robust business management systems in place to ensure the sustainable use of water from the GAB including ISO9001 and ISO14001 systems to deliver the targeted outcomes and obligations of the Olympic Dam Environmental Management and Monitoring Program. The management systems ensure that Olympic Dam retains accountability for its water demand from the GAB over the life of the mine. This accountability has delivered continuous improvement in water use efficiency driven by operating discipline, implementation of water saving projects, using water on a fit for purpose basis including substitution from non-GAB sources, and risk management to prevent and mitigate water supply disruptions to Olympic Dam and Roxby Downs. Since the establishment of Olympic Dam, BHP Billiton has funded a reduction in GAB water flow from bores, previously going to waste, that is greater than the annual average flow used by Olympic Dam.

Jan 1, 2009

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By F Soleimani

Coal and gas outburst is a common hazard in coalmines and due to the complexity of its nature, efficaciously predicting the possibility of its occurrence is intricate. The mechanical and gas flow properties of coal, in situ and mining-induced stresses and geological structure are involved in outburst occurrence, whereas suggested thresholds for its prediction do not consider them all. Numerical modelling is known as an effective method that can not only consider couple the effect of different physics but also analyse the effect of associated parameters. In this paper, a coupled fluid flow and geomechanics model has been developed in COMSOL Multiphysics to simulate outbursts by considering the effect of gas pressure and composition, damage mechanics on related coal properties, and progressive excavation and mining-induced stress. For the proposed fully coupled outburst model, the effect of pore pressure and sorption are applied to the stress while the influence of stress changes and damage are considered in updating coal porosity and permeability in each time step. In addition, to study the effect of mining-induced stress, the excavation process is simulated by changing the material properties over time according to the schedule of heading development. Then, outburst initiation is analysed from the energy point of view by using the concept of energy conservation law. The simulation results are used in calculating energy sources of the outburst initiation, also, the effect of particle size and ejection velocity are studied, and the significance of particle size effect on the energy analysis and deformed coal on outburst initiation is discussed.

Oct 12, 2022

By Cliff D, Harrison P. Hester C

During 1997 two different types of coal mine inertisation equipment were trialed in separate underground coal mines in Queensland.In April 1997 tests of the Polish developed GAG-3A inert gas generator were carried out at the Collinsville No 2 Coal Mine. These demonstrations indicated that the GAG-3A device was applicable in underground coal mines and that with respect to inertisation rate the device outperformed all other currently available techniques. The unit was assembled rapidly and operated safely during surface and underground trials and no mechanical problems were encountered with the device. The GAG-3A is not suitable for every fire scenario particularly if large volumes of fresh air are being drawn into the mine(where multiple units may be required), but with respect to the selection criteria developed by the Moura Implementation Process Task Group 5 criteria, the unit performed up to the specifications required.

Jan 1, 1998

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By Atalla YM

Steel rolling mill product finishing pro cesses gradually become or often already are unsuited for current production and marketing conditions. Indications are made as to what has been done to (i) rectify situations of this kind and, (ii) to reduce both product finishing time and costs. The principal features of two separate case studies are reviewed, these being (a) the finishing-end of B.H.P.'s Newcastle o.2 Merchant Mill and, (b) a mixed functions finishing yard and warehouses group (known as he Merchant Mills Loading Yard) which has been perating for a number of years. The areas in ach case are identified as a system while the arious functions, principal product streams nd processing equipment are respectively iden- ified as sub-systems and system elements. etails are given of the models used in each Sub-system dependency on the system as a le is traced by means of an information and ision analysis or by time studies and the sonableness of the system elements is deter- ed by computer programming or by simple com- ison methods. The-accumulated data is used derive improved mill finishing-end or Load Yard,functioning concepts according to pro- rules whilst at the same time considering

Jan 1, 1975

An empirical method of estimating dense rock (D.R.E.) equivalent volumes erupted as airfall tephra, described in a companion paper in this volume, is elaborated, and its accuracy discussed. Estimates obtained from a single eruption can be classified as to whether they show positive, negative, or constant relative dispersion. For positively dispersed tephras (estimated volumes increasing with distance), this procedure improves the accuracy of the method. The technique is applied to selected andesitic tephras erupted from Egmont Volcano, New Zealand, during the last 28 000 years, which are found to range in volume from about 1.5 x 107 m3 up to about 2.4 x 108 m3 D.R.E. With a factor of about 16 between the smallest and largest volumes, this contrasts sharply with the rhyolite volcanoes in New Zealand, where the difference factor is usually of the order of 100. The largest tephra eruptions at Egmont are small compared to the largest debris avalanches, which have exceeded 1010 m3 (10 km3) in volume.The magnitude versus frequency relationship, calculated using a maximum likelihood method, establishes the limits of eruption magnitude at Mt Egmont as 107 to 109 m3 D.R.E. For some volcanoes, the magnitude-frequency relationship changes with time, owing to clustering of eruptions, separated by long dormant intervals. Ngauruhoe Volcano, New Zealand, is an example. Within eruptive episodes, the mean interval between eruptions of >_ 105 m3 is about 0.9 ¦ 0.65 years. The mean interval between eruptive episodes in which >_ 106 m3 is erupted, including episodes in which this volume is erupted gradually, is about 25.8 ¦ 6.6 years, and the mean dormant interval between all episodes is about 5.2 ¦ 3.0 years. At present Ngauruhoe is in an unusually prolonged dormant period, 50% longer than any in the historical record, since 1839.

Jan 1, 1990

By P Ritchie, E H. Briese, N A. Currey

Kidston Gold Mines, located in semi-arid North Queensland, Australia is currently in its closure phase. Highly innovative and comprehensive rehabilitation strategies were employed at the site, including the direct revegetation of the surface of the tailings storage; the construction of a tailings sediment entrapment pond; the construction of a spillway to drain large rainfall events from the surface of the tailings; the construction of store/release covers over the tops of the waste rock dumps; the sheeting with oxide waste rock of the waste rock dump slopes; the partial back-filling of the initial Wises Hill Pit with waste rock and thickened tailings produced from the subsequent Eldridge Pit; the partial flooding of Eldridge Pit following the end of mining; and the construction of wetland systems to treat contaminated tailings and waste rock dump seepage. These closure strategies involved the careful consideration of water management. Specific water management issues included understanding the water balance of the tailings dam; the operation of the tailings dam sediment entrapment pond and spillway; understanding the water balance of the store/release waste rock dump covers; the importance and sustainability of vegetation on the tailings, store/release waste rock dump covers, and on the sheeted waste rock dump slopes; the level and quality of water in the partially flooded Eldridge Pit; and the treatment of contaminated seepage in the constructed wetlands. The seasonal and highly variable rainfall experienced in this semi-arid climate posed a number of challenges for the management of water on the site post-closure. The paper details these challenges and highlights how they were resolved over the period leading up to and following the end of mining.

Jan 1, 2003

By G Le Juge, K Waldock

The current suite of bulk mining explosives has been available to the industry for over 20 years. The flexibility and performance of ammonium nitrate based emulsion blend explosives were accepted by the mining industry in the early 1980s. These water resistant explosives rapidly displaced the water gels and slurries developed during the previous two decades. However, since the 1980s there has been no equivalent step change to the basic formulation or application of bulk explosives, although there has been a continuous process of refinement with respect to stability, handling characteristics and most significantly, cost. In the 1980s explosives supply contracts were awarded based on technical evaluations, usually accompanied by field trials. Technical personnel from both mining companies and explosives suppliers dominated the negotiations and there was a strong focus on explosive energy and blasting requirements. Today, explosives from alternative suppliers are difficult to differentiate on the basis of energy so the focus has shifted to aspects of service and price û bulk mining explosives are now largely treated as a commodity and the negotiations are dominated by commercial personnel. Commercial pressures from large mining companies have seen a substantial reduction in the real price of explosives. However, this has come at a cost. In order to reduce manufacturing costs, emulsion formulations have changed. In general they are not only cheaper, but also less energetic. Powder factors have had to increase to achieve the same blasting results, especially in hard ground. It is debatable whether the mining companies have achieved all of the economies they were seeking. This paper discusses these issues and argues that the mining industry would benefit from taking a more technically driven approach to meeting their blasting requirements. Recent trends towards more open contracts between the mining companies and their suppliers can be extended to explosives. To achieve this, mining companies will need to acquire sufficient technical knowledge to take a more pro-active approach to specify the characteristics of the explosives required to maximise the economic performance of their operations.

Jan 1, 2004

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By H Park, L Wang

Froth flotation is one of the most widely used beneficiation processes for fine and ultrafine coals and minerals. Maintaining optimal metallurgical performance in industrial flotation operation is still a challenging task owing to the lack of an effective tool to diagnose the flotation performance in realtime. For this purpose, a number of flotation performance monitoring systems with different working principles have been developed to provide instant feedback for process control and optimisation. In this paper, for the first time, five different flotation performance monitoring systems were systematically compared through an on-site trial in a coking coal flotation plant in Queensland, Australia. The monitoring systems were used to measure (i) gas holdup, (ii) overflowing froth velocity, (iii) overflowing froth height, (iv) air recovery and (v) drag force exerted by overflowing froth, in an industrial flotation column and the outputs of these systems were collected simultaneously at a wide range of operating conditions. For each monitoring system, the best regression model describing the correlation between the system output and the flotation performance was selected from various regression models (eg linear, quadratic, power-law and logarithmic) using the Akaike information criterion (AIC). A comparison of the coefficient of determination (R2 ), residual sum of squares (RSS) and measuring accuracy at 95 per cent confidence level of the best regression models of these monitoring systems suggested that the drag sensor outperformed the other systems at a wide range of flotation operating conditions. The superior performance of the drag sensor was attributed to its distinctive design that enabled intimate sensing of variation of the overflowing froth properties. Furthermore, the drag sensor had the ability to monitor feed ash content variation when the other operation variables were set almost constant.

Aug 24, 2022

By R C. A Minnitt

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the fundamental sampling error (FSE), the duplicate sampling analysis (DSA) and the segregation fractionalised analysis (SFA) are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody is calibrated using the DSA and SFA methods and the results are compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to a power of 3. Gy’s formula is a theoretical formula applicable in the case when fragments are randomly collected one by one, which is obviously never the case. This is because the fragment shape factor (f) and the granulometric factor (g) were introduced to take care of this anomaly. More recent formulae, such as those suggested by François-Bongarçon and Lyman, are empirically based formula. A later modification of Gy’s formula raises dN to the power ? (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of ? (alpha) for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of alpha in the range 0.97 to 1.30. The average value for alpha is found to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry preference for 1.5. It is suggested that for low-grade gold bearing ores, the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the combined FSE plus the grouping and segregation error, now referred to as the short-term component of the quality fluctuation error (QFE1), greatly simplifies the characterisation of gold ores, which now only requires the calibration of K for a given mass and established fragment size. The implications for the heterogeneity test from the generalised equation are that provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.CITATION:Minnitt, R C A, 2017. A generalised form of Gy’s equation for gold ores – empirical evidence, in Proceedings Eighth World Conference on Sampling and Blending , pp 331–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986