Search Documents

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Baxter C. Madden

Stress corrosion is defined and certain examples are illustrated. A number of test methods, to determine the resistance of materials to stress corrosion, are being developed at Wright Field. The criterion as to the validity of a method is stated. Three types of specimens and the method of stressing each type are described. Five different corrosive conditions are set forth. The results of tests to date, although too few for any general conclusions to be arrived at, are presented. The program for the continuation of the investigation is indicated. A bibliography is included. The development of the method of loading a cantilever-type specimen, so that a nearly constant stress at a large deflection may be realized, is presented as Appendix I.

Jan 1, 1945

By John M. Kelly

New Mexico produced 39,475,388 bbl. of oil in 1944, the greatest amount in one year in the oil history of the state. This production was 593,046 bbl. or 1.25 per cent more than in 1943. New Mexico retained its position as the seventh largest oil-producing state. The maximum per well allowable on Jan. I, 1944 was 48 bbl. daily and at the end of the year it was 45 bbl. daily. Allocations as set by the New Mexico Oil Conservation Commission closely followed the recommendations made by the' Petroleum Administrator for War. The average daily pipe-line runs were within 4 per cent of the allocation. Production by counties was as fol1ows;Lea County, 33,509,548 bbl.; Eddy County, 5,504,498; Northwestern New Mexico 461, 342. Drilling activity for New Mexico in 1944 was well above that of 1943, with 362 completions. Of these, 283 were oil wells, 12 gas wells and 67 dry holes. The ratio of dry holes to producers, about I to 4, was an improvement over 1943. Wildcat drilling during 1944 was responsible for the discovery of six new fields and the extension of two present producing areas. Drilling records were established in New Mexico during 1944 with the deepest producer ever completed, the Humble Leonard Oil Company's No. I at 11,969 ft., in the Ellenburger section of Ordovician age near Jal, Lea County. The discoveries in Lea County during 1944 were as follows: West Lovington field, where Fred Turner, Jr. drilled his No. I State B .in C SE SW sec. 4-17-36 and completed it for 122 bbl. of oil in 8 1/2 hr., in the San Andreas section of Permian age. The Tonto field, where the T-exas Company completed its No. I Baskin at a total depth of 3586 ft. in Seven Rivers lime of Permian age, with an initial production of 254 bbl. of oil in 21 hours. The Drinkard area, where the Gulf Oil Corporation's Drinkard No. I flowed 782 bbl. of oil in 14 hr. from the Yeso section of lower Permian age, thus opening the first lower Permian production in the state. The total depth of this discovery was 6508 ft. and oil was 38.8" A.P.I. gravity. The Dublin area, where the Humble Oil and Refining Co. established a drilling depth record of 11,969 ft. drilling and completing its No. I Leonard Oil Co. well in the Ellenburger lime of Ordovician age. This well flowed 221 bbl. of oil per day, of 48.9º A.P.I. gravity oil. It is in sec. 12-26-37. The new pay horizon discovery of the Continental Oil Co. in the Skaggs area, where the company completed its Skaggs B-23 No. 2 in sec. 23-20-37 for 236 bbl. of oil in 21 hr. from the Wolfcamp section of lower Permian age, at a total depth of 7725 ft. This well was drilled to granite at 10,465 ft. and plugged back to the Wolf-camp for a new pay zone completion.

Jan 1, 1945

By P. E. Fitzgerald, J. C. Gindlesperger

1. The Acidizer (Trade Publication of Dowell Inc.): No. 1. Aspects of Acidizing. No. 2. Inhibited Acid. No. 3. The Value of Acidizing. No. 4. The Chemistry of Acidizing. No. 5. Jelly Seal in Acidizing. No. 6. Loosening Stuck Drill Pipe. No. 7. The Geology of Acidizing. 2. J. C. Albright: Acid Is Being Used for Cleaning Intake Wells in Water-flooded Areas. Oil Weekly (Sept. 23, 1935) 24. 3. D. H. Bancroft: Acid Tests Increase Production of Zwolle Wells, Miller County, Arkansas. Oil and Gas Jnl. (Dec. 22, 1932) 42. 4. A. H. Bell: Possible Areas for Acid Treatment in Illinois. Pub. of Illinois- Indiana Petr. Assn. and lllinois Geol. Survey (1934) 49. 5. N. A. Best: Treating Limestone Formations Consists of More than Pouring Hydrochloric Acid in the Well. Oil and Gas Jnl. (April 5, 1934) 54. 6. L. G. E. Bignell: Sealing Off Salt Water from Oil-bearing Formations. Oil and Gas Jnl. (Jan. 30, 1936) 59. 7. L. G. E, Bignell: Acidizing Upper Limestone Formation Facilitated by the Use of Jelly Seal. Oil and Gas Jnl. (March 5, 1936) 30. 8. L. G. E. Bignell: Bailing, Shooting, Tubing and Acidizing Have All Been Tried in Deep Test at Binger, Oklahoma. Oil and Gas Jnl. (May 10, 1934) 38. 9. L. G. E. Bignell: Dowel1 Incorporated Increasing Its Field Service for Acid Treatment of Wells. Oil and Gas Jnl. (June 7, 1934) 62. 10. L. C. Chamberlain, Jr. and P. E. Fitzgerald: Oil Well Acidizing in Michigan. Mich. Acad. Sci. Papers (March 1937). 11. M. E. Chapman: Some of the Theoretical and Practical Aspects of the Acid Treatment of Limestone Wells. Oil and Gas Jnl. (Oct. 12, 1933) 10. 12. C. E. Clason and J. G. Staudt: Limestone Reservoir Rocks of Kansas React Favorably to Acid Treatment. Oil and Gas Jnl. (April 25, 1935) 53. 13. W. F. Cloud: Cleaning and Reconditioning Oil Wells—Reconditioning by Use of Acid (Petroleum Production 1937), 389. University of Oklahoma Press, 1937,' 14. K. A. Covell: Developments in Eastern Production Practice. Acid Treatment of Michigan Wells. Amer. Petr. Inst. Prod. Bull. 213 (1934) 77; Oil and Gas Jnl. (May 31, 1934) 89; Oil Weekly (May 28, 1934) 17. 15. B. A. Cunningham: Acid Treatment of Lime Formations. Amer. Petr. Inst. Paper 901 (1933) 9D, 1-7. 16. 0. I. DeSchon: Pondera Production up 22,000 Barrels. Montana Oil & Min. Jnl. (Jan. 26, 1935) 1.

Jan 1, 1937

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By AIME AIME

THE Engineering Education Committee of the Institute convened at the Engineering Societies Building on Feb. 18, .1929, with. E. A. Holbrook, dean of the Schools of Mines and Engineering, University of Pittsburgh, in the chair. STATISTICAL' STUDY OF STUDENTS IN MINING The first paper, a statistical study of the students enrolled in courses leading to a mining degree in 40 institutions, was presented by H. D. Keiser,, assistant editor of the Engineering and Mining Journal; who gave a brief outline of an article he was about to publish in ?that journal?. The complete article appears in the issue for March 30; 1929: To avoid repetition the results are summarized as follows: A request was sent to 42 institutions which give courses in mining' for the number of students enrolled as freshmen; sophomores; juniors, seniors and special students in mining for the years 1925-26, 1926-27, 1927-28, 1928-29. Two of these colleges replied that there were no students in mining. Students' enrolled in courses in metallurgy, geology and engineering, other than mining, were excluded from the statistics:. The statistics received were arranged in, four groups, according to the completeness of the information. One complete group of 25 institutions 'shows as follows:

Jan 1, 1929

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

US 4,133,866-Selective recovery of the bound sodium content of red mud obtained in the production of alumina by the Bayer process The red mud is mixed with aqueous ferric sulfate, the resulting suspension stirred intensively at a temperature of 15-85°C and adjusted to a pH value of from 4.4 to 4 6, and the solids are removed. The clarified solution of sodium sulfate can be used directly for the leaching of additional bauxite T Lakatos, M Miskei, J Szolnoki, F. Toth, and L Revesz, assigned to Aluminiumipan Tervezo es Kutato Intezet, Almasfuzitoi Timfoldgyar, and MTA Geokemiai Kutatolaboratorium. Jan. 9, 1979. 3 pp (423-208). Filed: 10¬28-77 (846,588) Priority: Hungary, 10-29-76 (AU 364). US 4,145,398-Continuous digestion of bauxite with aqueous sodium hydroxide, with higher throughput in existing plants or the construction of smaller plants with equivalent capacity The ore suspension at a solids concentration of 1-6% by weight and temperature of 200-300°C is flowed through a digestion tube or nest of tubes at a velocity of preferably from 2 to 5 m/s and under a pressure of from 10 to 200 atm Heat is supplied by a fluid heat carrier flowing in countercurrent in a concentric outer tube. Preferably, some of the red mud is recycled to the digestion operation. L. Plass, assigned to Vereinigte Aluminium-Werke A.G Mar 20, 1979. 5 pp. (423-121) Filed: 2-27-76 (754,749) Same: British 1,437,548, dated May 26, 1976 Same Canadian 1,008,253, dated Apr 12, 1977. US 4,146,573-An aqueous slurry of red mud, formed in the Bayer process production of alumina from bauxite, can be solidified by treating the red mud with a described quaternary ammonium salt, continuing mixing until the red mud has set up to a rigid mass, and recovering the solidified concentrated red mud J Kane, assigned to Nalco Chemical Co Mar 27, 1979 4 pp (423-82). Filed 8-2-78 (930,251).

Jan 1, 1980

Jan 7, 1976

By A. D. Hughes

C. W. MERRILL*-Mr. Hughes' paper not only is very well presented but is most timely in that it covers a subject of vital interest to the United States. Tin is one of the strategic metals which has not been found here in appreciable quantities. The total United States tin output since the first recorded production over 100 years ago would not supply current consumption for a fortnight. On the consumption side, tin is extremely important in national defense because of its use in tin plate which, in the form of tin cans, makes it possible to feed properly the armies that the United States recruits from its civilian population in emergencies. Moreover, the internal combustion engines so important in powering tanks, planes, and other war machines, require large quantities of tin alloys for bearings and for soldering. These considerations, along with the fact that Malaya, historically, has been the leading source of tin to the United States, make the kind of information that Mr. Hughes has presented so ably, a matter of vital interest.

Jan 1, 1949

By H. L. TERWILLIGER

THOSE of us who have been following rock drilling work for the last 15 or 20 years can recall some of the problems that were encountered with the old piston type of rock drill and the solid steel which it used. There was frequent trouble in keeping a straight hole in badly broken ground when using the ordinary four- point bit that had a flare on the wings of about 14". The drill steel, when pounding down its hole, would follow the line of least resistance and draw away from the desired line when it encountered a weak side in the ground through which it was drilling. Some would overcome the difficulty by making long winged bits to prevent the steel crowding over; this would relieve the troubles to a great extent. There was trouble with the rifling of drill holes and inability to drill round holes in some ground. The cure for these ills was to use the "X" bit, rather than the crossbit. The "2" bits were brought out in an effort to make it easier to drill a round hole in bad ground. Most of these troubles were before the days when the mechanical drill sharpener was in as common use as it is today. It was not until the introduction of the Leyner type of rock drill, requiring hollow steel that the users of rock drills found themselves confronted with more difficult prob- lems than they had ever encountered before with drill steel because the steel had to stand more severe service.

Jan 1, 1924

The economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publications of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photographs are used on such scales as 1/5000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are interpreted can be grouped under the following headings: 1. Continuity.—The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937

By Samuel B. Christy

Columbia College has the honor of founding the first well-organized School of Mines in America. The University of Michigan, however, shared with her the honor of graduating the first class, in 1867. Prof. Thomas Egleston was the pioneer in the new movement. He drew up the original plan for the Columbia School of Mines in 1863, and was in 1864 appointed its first professor. The Massachusetts Institute of Technology turned out a class of mining students a year later, and others followed in the order of their first graduating class, as shown in Table I., condensed from the Engineering News of August 11, 1892. Besides those mentioned, mining schools have been organized in the States of Arizona and Nevada, and more or less instruction is advertised in connection with other engineering schools. It will be noticed that Columbia easily heads the list with reference to the number of graduates; the Massachusetts Institute of Technology stands second ; the California University third, and then follow Lehigh, Washington University, the University of Michigan, Lafayette College, Michigan Mining School, Missouri, Colorado and the others. The total number of graduates from these 16 schools in 26 years, has been 871, or an average of 33 per year; but as all these schools give a partial education to many who do not graduate, it is probable that from 2000 to 3000 mining students have received from them considerable training. An interesting comparison of the rate of growth of the engineering schools has been recently instituted by the Engineering News, for the period between 1860 and 1892. Table 11. shows that civil engineering had the advantage in numbers from the start, and maintained the advantage until 2890, when it was surpassed by mechanical engineering. The development of the latter course may be said to date from 1880. There are many interesting facts evident in Table 11. It will

Jan 1, 1894

By AIME AIME

THE following Officers, Directors, and guests were present: Herbert Hoover, A. R. Ledoux, Henry S. Drinker, Edwin Ludlow, Samuel A. Taylor, Charles F: Rand, William M. Corse, Arthur S.. Dwight, Glen H. Clevenger, L. W. Francis, F. G. Cottrell, Bradley Stoughton, Percy E. Barbour, E. P. Mathewson, Dorsey A. Lyon, Archibald Douglas, A. D. Flinn, RobertLinton, James F. Kemp, William Y. Westervelt, J. W. Richards, W. L. Saunders, George Otis Smith, Thomas T. Read, J..C. Murray, Ralph Arnold. A Committee on Mine Equipment was appointed composed as follows: Graham Bright, chairman, William Kelly, Howard N. Eavenson, R. E. Hobart, and S. P. Rumsey. B. D. Saklatwalla was added to the Committee on Miscellaneous Metals and W. Spencer Hutchinson was added to the Committee on Mining Geology. A revised budget for 1921 was approved. A petition duly signed to amend Section 1., of Article III of the Constitution, increasing the initiation fees from ten dollars to twenty dollars, was approved by the Board.

Jan 1, 1920

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By L. Kovisars, F. Buttazzoni

The current demand for copper in the western world exceeds 7 million tonnes annually. The growth in demand is expected to average 2.6% annually to a level exceeding 11 million tonnes in 2000. Copper mine production is currently about 6 million tonnes annually; the annual net addition to mine output in the future will have to average about 190,000 tonnes of contained copper. The industrial nations of Europe and the western Pacific are heavily dependent on copper imports. Currently these import needs are supplied by Canada, Africa and Pacific producers. The increased demand for copper in the future is expected to further weight the trade balance to the Pacific suppliers. An evaluation of undeveloped deposits allows the ranking of these deposits based on total cost of production, including provision for plant and infra- structure investment as well as political/social/ economic risk. Peru, Canada, and the Southwest Pacific are expected to significantly increase exports. The United States will develop deposits to replace depleted mines, maintaining mine production at a level approximately equal to current output, with a consequent increase in copper imports. Chile is expected to become the world's leading copper producer, as well as expanding it's position as the leading exporter.

Jan 1, 1982

By J. R. Linney

APPROXIMATELY 5,788,000 long tons of crude ore was produced by the Eastern magnetite industry in 1946, or a drop of 26 per cent compared -with 1945. Decrease in production -throughout the industry varied from :8 per cent for the mine with the lowest reduction to 49 per cent for the mine -with the highest reduction. At the Chateaugay mine, operated by :the Republic Steel Corp. at Lyon Mountain, N. Y., 426,900 long tons of crude ,ore was produced, yielding 129,500 long tons of concentrates or a reduction of 46 per cent compared with the previous year. Owing to a strike the mine was closed down from Jan. 21 to July 29. At the Mineville mines, also operated by Republic Steel, output was 755,000 long tons of crude ore or a reduction of 49 per cent compared with 1945. The yield from the crude ore production consisted of 51,500 long tons of lump ore and 380,000 long tons of concentrates. The Mineville plant did not operate from March 17 through July 28, on account of the strike. The Fisher Hill mine, which produced 93,000 long tons of crude ore, included in the above figures, has not operated since March 17, 1946.

Jan 1, 1947

Sponsored by the Utah Section of AIME, the 1960 Annual Rocky Mountain Minerals Conference brought more than 500 members of the mineral industry to the conference rooms of the Newhouse Hotel in Salt Lake City during the period October 5 to October 7. Under the overall supervision of J. M. Ehrhorn, general chairman, and H. E. Wright, assistant general chairman, the Conference offered 14 papers of technical interest in four sessions during the first two days, and it culminated in the Exploration Symposium held on the morning of October 7. The opening session of the Conference, meeting on the morning of October 5, heard R. P. Work, utility engineer of the Mountain Fuel Supply Co., discuss the growth and economic factors related to the use of natural gas in Utah. In his paper entitled Natural Gas Market In Utah, Mr. Work emphasized the very good prospects of natural gas serving almost all parts of that state. He mentioned that recently the El Paso pipeline, built to serve the Pacific Northwest with gas from Texas, has permitted natural gas to be available to Eastern Utah, and a tentatively planned pipeline from Green River, Wyo. to Southern California will bring natural gas to the central and southeast areas of the state.

Jan 11, 1960

By N. H. Emmons

(Canal Zone Meeting, November, 1910.) AN interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at this plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory., Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaces. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top was necessary and the engineering force was started oil the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of cast copper, but the heat was so great that the copper bent readily, due to the jarring of its * General Manager, Tennessee Copper Co.

Feb 1, 1911

By C. E. LAWAL

WITH the object of adapting high-school vocational courses to the industrial needs of the community, a few high-school officials in West -Virginia working with the School of Mines of the State university decided to try an innovation this year. The purpose of this experiment was to teach coal mining in two high schools situated in mining communities. We thought that if a course in coal mining would be included in the list of optional courses offered in the high school, it might interest some of the boys, and if the course were properly taught it would undoubtedly be of inestimable value to those boys who later decided to take up mining work as their vocation. This coal-mining course was started last September in the Berwind and Gary high schools in West Virginia. The high-school officials in their conferences with' us decided that we should work up the outline of this course and they would assign the science teachers of the schools as instructors, with ,the understanding that we would help 'these instructors with this work. We consented to all this and submitted -an outline to the school officials which they are following this year.

Jan 1, 1929