Search Documents

By J. E. Spruiell, F. H. Patterson, B. F. Shuler

The microstructures and textures developed by the working of high-purzly thermochemically deposited tungstem sheet have been inuesligated. Greater than 60 pct reduction was required to deslroy the columnar grain structure which existed in the as-deposited sheet. With increasing reductions the texture gradu-ally charged from the initial as-deposited orientation with (100) parallel to the sheet normal to a (100}(011) ideal ovienlation with some spread about the rolling direction. This texture was retained after recrystalli-zation a1 2000°C. THE processes for depositing tungsten by hydrogen reduction of tungsten hexafluoride have been under development for the past several years.1,2 The nature of the deposition process is such that the as-deposited material contains a highly oriented columnar grain structure perpendicular to the deposition substrate. This well-defined columnar structure may be useful in certain applications293 but a wrought or equiaxed structure may be desired for some components such as tubing. Knowledge of the effects of working ther-mochemically deposited (TCD) tungsten is therefore necessary in order to establish the feasibility of obtaining worked and recrystallized microstructures and textures. The details of a recently developed technique for thermochemically depositing flat, uniformly thick tungsten sheet are presented with emphasis on the effects of deformation by rolling on the microstructure and texture. Although no work has been previously reported on the rolling and the annealing textures of TCD tungsten, there have been some determinations of textures for cold-rolled tungsten foil prepared from powder-metal -lurgy billets.4-8 The general description is that of a predominantly lurgy{100}(011) texture, with some spread about the rolling direction as an axis. pugh5 reports data both for cold-rolled and for annealed foil having about 96 pct initial cold work. He observed no change in texture, except for a decrease in the spread, for annealing treatments of 30 min at temperatures up to 1800°C. On annealing at 1900°C, both the low-temperature components plus new components which were described alternately as {001}(320) plus {001)(230) or as {100}(011) ± 12 deg about the sheet normal were observed. Above 1900°C, the new orientation existed alone, and it was stable up to 2500°C, the highest temperature that Pugh investigated. THERMOCHEMICAL DEPOSITION OF TUNGSTEN SHEET High-purity tungsten sheet was reproducibly deposited on the inner walls of a molybdenum mandrel by the thermochemical reaction WFs(g) + 3H2(g) - W(s) + 6HF(g). The mandrel was heated by a five-zone tube furnace which afforded a controllable fixed-temperature profile. Sheets measuring 1+ by 12 in. have been deposited with uniform thicknesses of up to 0.145 m. As shown schematically in Fig. 1, the purified reaction gases were metered into a mixing chamber at a Hz-to-WF6 ratio of 15 and preheated to 350°C. The flow rate of the WF6 was 300 cu cm per min at stp. These gases were directed through a conical injector into the deposition chamber. Inside this chamber hydrogen reduction of the WF6 to pure tungsten metal occurred on the hot walls of the molybdenum mandrel at a total pressure of 5 Torr. Typical temperatures for the five zones in the chamber were, respectively, 565", 540", 550°, 570°, and 590°C. The hydrogen fluorlde generated from the reaction, the excess hydrogen, and some un-reacted WF6 were pumped on through the scavenger

Jan 1, 1968

By B. L. Landrum, P. B. Crawford

The rise of a new laboratory model for studying tran-sient fluid flow problems, is described. The theory of he model is based on the analogy between the equa-ions which describe the flow of compressible fluids in porous media and the conduction of heal m solids. The "thermal model" is used to study the Iransient Pressure distributions during fluid displacement in five Standard well patterns. The studies indicate quantita-ively how die pressures change with lane at any poit in the reservoir. It was found that, in general, the equipressure contours are more radial about the wells early in the program than after steady-state conditions are established. In addition two studies of fractured five-spot patterns are presented to illustrate the opplicability of the model for a wide range of reservoir conditions. INTRODUCTION In reviewing the oil recovery techniques involving fluid displacement it was found that a very considerable quantity, if not all of the fluid within the pattern, mav be displaced (during a time-dependent or transient period rather than the usually applied steady-state conditions. Since the oil is displaced during a transient period, it was believed desirable to study the nature of the transients for several of the commonly used fluid displacement patterns. A literature review indicated fairly complete studies of the streamlines and isopotentials for steady-state: yet few data were available on the transient displacement process. Several simulated steady-state multiwell displacement programs were carefully mapped by Foster and Lodge on an electrical conducting sheet as early as 1875, hut the more recent work of Muskat provides the best source for steady-state phenomena having direct petroleum production applications. In order to study the transient phenomena a new lab-oratory model was developed which is based on the similarity of the equations that describe the flow of fluids and the conduction of heal. The equations describing heat flow were developed early in the nineteenth century. Regorous solutions tor most transient problems are in gcneral complex and usually limited to fairly restricted houndary conditions.2 the thermal model may be used to obtain approximate solutions for many transient problems without some of the restrictions required for analytical solution. The application of the analogy between heat conduc-. tion in solids. electrical flow and fluid flow, in a porous media has long been recognised. Techniques originally developed for the solution of heat conduction prol?lems have in many instances proved useful in ohtaining solutions to fluid flow prohlcms. Ir is not surpri5ing then that a heat conduction or thermal model might bf usefull in sludying transient fluid flow. As an example ol the problems suitable for the study with the thermal model, transient pressure distributions during fluid displacement programs are studied for the five-spot, line-drive, staggered line-diibe. seven-spot 211 two fractured patterns. A model was constructed of an iron plate of geometry similar to the reservoir patterns under study. The principle of mirror images as suggested by Bryan was employed in shaping the model. A temperature differential was obtained by soldering two sections of copper tubing to the plate at points analogous to the well location in the field. Hot and cold water was passed through the tubing. The temperature distribution, analogous to the pressure distribution in the field. was obtained a a function of time from thermocouplcs distributed over the plate.

By P. Barnes

Exact accounts hare been kept of the cost of these chimneys, and it may he a matter of some possible interest. that the plans and details of cost should be laid before the Institute. The statement of cost herewith submitted does not give minute particulars of the weights or quantities of material used, although these are noted upon the company's books.

CONTRARY to the natural order of art, it has been discovered how to cast in moist earth in order to avoid labor and expense. This is truly a thing that many desire and few practice because it is not as smooth a way nor as easy to effect as it apparently seems. To do this, one part of fine-grained yellow tuff is taken, or some very

Jan 1, 1942

The 140th meeting* of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb. 16 to 19, 1931. It consisted of the annual business session, twenty-six technical sessions at which 149 papers were presented, two round table discussions, two meetings of the Board of Directors, three meetings of Section Delegates, two formal lectures, four group dinners and 11 group luncheons, luncheon daily for members and guests, 20 committee meetings and conferences, the annual reception and dinner dance, an informal dance, a smoker-dinner, two meetings of the Woman's Auxiliary and a special program of entertainment for the ladies. Former members of the Rocky Mountain Club and friends lunched together at the Engineers Club on Tuesday. The proceedings of the Iron and Steel Division included four general technical sessions, an Iron Ore Round Table, the Howe Memorial Lecture, the Division luncheon at the Engineers Club Wednesday noon, a session each of the Executive Committee and the Committee on Nondestructive Testing, a luncheon each of the Committee on the Manufacture of Alloy Steel and the Blast-furnace Conference Group, and a dinner of the Committee on Physical Chemistry of Steelmaking. Dr. F. F. Lucas delivered the Howe Lecture, the title of which was "On the Art of Metallography." The Institute of Metals Division held three general sessions, its annual lecture, which was delivered by Dr. Arne Westgren and entitled "X-ray Determination of Alloy Equilibrium Diagrams," and a Division dinner at the Hotel New Yorker Thursday evening, at which Dr. G. W. Thompson was the principal speaker. The Executive Committee assembled at a luncheon on Thursday. A round table on Coal Land Valuations, a general technical session and a Division luncheon were held by the Coal Division. C. E. Bockus, President of the National Coal Association, made an informal talk at the luncheon which was held at the Engineers Club Monday noon. The Petroleum Division held six general sessions, including its annual production symposium. The annual dinner was held at the Engineers Club Thursday evening. A Gold Supply Symposium was the feature of the proceedings of the Committee on Mining Geology. This Committee also held a general session and a luncheon meeting. Sessions were held by other Technical Committees as follows: Mining Methods, 2; Mine Ventilation, 1 (besides which the Committee on Mine Ventilation Code held a meeting); Ground Movement and Subsidence, 1; Milling Methods, 1; Nonferrous Metallurgy, 1; Engineering Education, 1 (also a Committee luncheon); Non-metallic Minerals, 1, and Geophysical Prospecting, 2.

Jan 1, 1931

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer's connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month's operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

DR FRANK DAWSON ADAMS Montreal, Canada HENRY STURGIS DRINKER Bethlehem, Pa PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England HERBERT C. HOOVER Leoben, Austria ROBERT W. HUNT Chicago, ILL JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico ALEXANDRE, POURCEL Paris, France RICHARD H, RICHARDS Boston Mass. JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia CHARLES D WALCOT Washington D.C.

Jan 1, 1923

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve Engineers. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22d Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers' Reserve Corps. BIGELOW, BRAXTON. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BROOKS, ALFRED H., Captain, Engineer Officers' Reserve Corps. BROWNE, DE Courser, 1st Lieutenant, Ordnance Dept., Fortress Monroe, Va.

Jan 8, 1917

By Ernest O. Kartinen

This report is the accumulation of eight years of experience on only one small phase in the business of oil production. It is not intended as a final report but rather as a progress report dealing with the internal corrosion of oil field dehydrating tanks. The corrosion of dehydrating tanks continues to be a problem in the production of crude oil. The deterioration hy corrosion of these tanks falls into three general classifications: (1) Atmospheric corrosion of exterior areas, (2) corrosion of the underside of deck and the rafters and top area of the upper row of staves in that part of the tank which is known as the vapor space, and (3) corrosion of the bottom and shell areas, and the steam coils which are normally immersed in water and thus exposed to the corrosive action of the water. Atmospheric corrosion is primarily a paint problem, and has been omitted in this discussion. The corrosion in the vapor space, in this company's experience, which has been of great concern only in one area. has also been omitted in this discussion. The third, and most troublesome type of corrosion, and the one with which this report deals, is that which occurs in the water-exposed areas of dehydrating tanks, and, to a lesser degree. in some stock tanks. The operating temperature of these waters varies from 80°F to 160°F and the salt counts run from a few thousand to as high as 25.000 parts per million. Corrosion in these tanks occurs in three forms: (1) pits, (2) ringworm type of attack along the vertical and horizontal bolt seams, and (3) as a general attack, spread over a wide area. Steam Coils In dehydrating tanks, our experience has been that the steam coils are the first to show signs of corrosion, and then the shell and bottom areas. This action is not uniform throughout this company's operations. Some installations have coil troubles with very little tank trouble, and some show just the opposite. But in the majority of cases the coils are the more seriously corroded areas. This may be partly due to the fact that we have tried by periodic application to keep a protective coating on the interior areas of the tanks, and some protection has been afforded by these coatings. Through the years several types of hot and cold coatings have been tried with many various methods of cleaning the steel, ranging from use of cleaning solvents to hot and cold Oakite washes, as well as sandblasting. Although experience has shown that a longer life expectancy of a coating is possible after a very thorough steel cleaning job, it has still been necessary to recoat these tanks at least every two or three years. Until a few years ago, vertical spiral steam coil bundles were installed when the tanks were originally erected. When these coils needed replacement, in some cases within 18 months, it was necessary to remove a couple of shell staves to accomplish this task. This required a down time period of several days and was often very inconvenient to the production operations of the leases. This problem was considered on the basis that the coils were expendable, and thus. to eliminate any unnecessary down time when changing coils, the vertical spiral coils were discarded in favor of horizontal flat coils which could be taken in and out of the tanks by way of the cleanout openings, and put together with unions. This made a fairly easily replaceable and repairable coil. But it was still very much of a nuisance when repairs were necessary. Efforts to increase the useful life of the dehydrating tanks led to the adoption of galvanized tanks at an increased initial cost. The zinc coating was depended upon for protection and no other protective coatings were applied. In July, 1944. during the development of a new lease, a 3-ring 1,500 bbl, black iron water tank was converted into a dehydrating tank with steam coils to handle the new production. This tank was coated inside with a cold, brushed-on coating, for protection against corrosion. After approximately 18 months of service, holes developed in the tank and the steam coils. The tank was emptied and cleaned for repairs. The coils were so badly pitted that it was felt advisable to replace them. Coating Becomes Loose Inspection of the tank showed the protective coating to be still in place but loose, and numerous blisters were in evidence. A closer inspection showed that the interior of this tank was so badly pitted under the coating that any further attempt to use the tank was inadvisable. This tank was therefore discarded and a new galvanized tank ordered and set up at considerable expense and inconvenience. In April, 1946, another dehydrating tank installation was made on an adjoining lease. This installation consisted of a 1,500 bbl. 3-ring galvanized tank with two sets of flat steam coils 12 in. and 24 in. up from the bottom. In September, 1947. seventeen months after installation. salt showed up in the boiler feed water. When the dehydrating tank was opened and cleaned, the steam coils were found to be badly pitted — several holes having penetrated through the wall of the pipe. New coils were installed.

Jan 1, 1950

By O. D. Gonzalez, H. A. Wriedt

Alloys ranging from pure iron to pure nickel were saturated with nitrogen gas at 918°, 999°, and 1217°C and analyzed. The solubility of nitrogen at 1-atm pressure was obtained as a function of nickel content for the whole range of iron-nickel alloys and the temperature dependence of solubility is shown for the experimental alloy compositions. The heat of solution and the entropy of solution of nitrogen in the alloys as func-tiom of composition up to 41 pct Ni are given. 1 HE acquisition of more exact thermodynamic information for systems composed of iron with various alloying elements continues to interest ferrous metallurgists. The interstitial alloying elements, especially carbon, hydrogen, and nitrogen, comprise a field of particularly intense study. A recent investigation of carbon solubility in Fe-Ni alloys held at 1000°C in gases of fixed carbon activity showed an unpredicted minimum in the solubility near 72 pct Ni.1 The present investigation was undertaken to see if a similar anomaly in solubility existed for nitrogen in Fe-Ni alloys. The solubility of nitrogen in ? iron at known nitrogen activities has been measured several times.&apos;-&apos; Corresponding information for the solubility of nitrogen in solid Ni and Fe-Ni alloys is not available. Juza and sachsze9 reported that metallic nickel dissolved 0.07 pct N in equilibrium with Ni3N at 445°C. This result was regarded as dubious by Turkdogan and Ignatowicz10 who found less than 0.0004 pct N in nickel specimens equilibrated at 600°C with ammonia-hydrogen mixtures having fugacities of N2 gas up to 35,000 atm. Such fragmentary reports indicate only that nitrogen gas has a very much lower solubility in nickel than in iron. MATERIALS A purified iron from Battelle Memorial Institute was used for solubility measurements. This grade contained more than 99.95 pct Fe, the highest content of any measured individual impurity being 50 ppm for each of As, C, Cu, and Pb. The nickel and iron-nickel alloys, supplied by the International Nickel Co., contained 0.02 to 0.04 pct C, 0.17 to 0.19 pct Mn, 0.04 to 0.08 pct Si, < 0.01 pct P, <0.03 pct S, and <0.20 pct Co as principal impurities. The Fe-0.59 pct Mn alloy was of zone-melted quality, the highest concentration of any individual impurity being 15 ppm Al. The "prepurified" grade of nitrogen gas from Matheson Co. had a nominal nitrogen content of 99.996 pct. An "electrolytic" grade of hydrogen gas from National Cylinder Gas. CO. in which the principal impurity is water vapor was admixed with the nitrogen to prevent oxidation of these specimens. This grade was preferred to a purer grade because the presence of some oxygen helps in suppressing contamination of the specimens, for instance, by silicon from the porcelain furnace tube. EXPERIMENTAL PROCEDURE The specimens were equilibrated in vertical tube furnaces through which a 99 pct N2-1 pct H2 gas was passed at ambient pressure. For the 915", 918", and 999°C runs, a wound-resistance furnace was used, and for the 1217°C runs, a furnace with a tubular silicon carbide element was used. The temperature control system on both furnaces was similar: a Weston "Celectray" controller with a modulator, responding to the electromotive force of a thermocouple with its hot junction in the furnace, switched the furnace current between high and low settings. The temperature distributions in the working zones of the furnaces were determined with calibrated Pt/Pt-10 pct Rh thermocouples. The overall uncertainty in temperature was estimated to be ±3° at 915° to 999°C and ±5° at 1217°C . Consideration of the small temperature coefficients of the equilibria studied, together with the error limits in the method of analyzing for nitrogen, showed that further refinement in temperature uniformity would give no improvement in resultant accuracy. The reactive gas was generated by mixing together "prepurified" nitrogen and "electrolytic" hydrogen directly from cylinders commercially supplied. The flow rates of nitrogen and of hydrogen were fixed by setting with bleeders the pressure drops across the individual calibrated flow meters of constant resistance. For any given alloy, the solubility of nitrogen at 1-atm pressure (% N) was obtained from the analyzed nitrogen content of equilibrated specimens (% Na)according to Sieverts&apos; law, thus

Jan 1, 1962

By P. Ramachandrarao, T. R. Anantharaman

EVER since the technique of quenching metals and alloys from the melt (splat cooling) was perfected a decade ago, it has been recognized that the grain size of products solidified by this technique may be extremely small.&apos; The further observation that fcc metals quenched from the liquid state contain very few dislocations has led to the inference2 that metals are subjected to negligible or no stresses during the rapid solidification characteristic of the "gun" or "piston-and-anvil" technique. Evidence for the incidence of appreciable densities of stacking faults has, however, been obtained in case of some splat-cooled fcc and hcp alloys,3 although not for pure metals. In the light of these earlier observations it was considered desirable to study X-ray line-broadening effects, if any, in fcc metals rapidly cooled from the melt. In the present work pure silver (>99.99 pct), aluminum (>99.99 pct) and lead (>99.9 pct) were quenched from the liquid state from temperatures about 50°C above the melting point by the "gun technique" and the resulting foils were subjected to X-ray examination in a Philips Diffractometer. The quenched foils (up to -10 u thick) did not generally stick to the substrate surface and could be easily transferred to the Diffractometer without introducing any plastic deformation. The profiles of the first five reflections from the foils were recorded in each case with Cu Ka, radiation at the slowest available scanning speed of 1/8 deg per min. To correct for instrumental broadening, profiles were also recorded from the metals annealed in vacuo at suitable temperatures. The integral breadths of the X-ray reflections were arrived at by a procedure described earlier.&apos; There was a distinct suggestion of preferred orientation in the recorded intensities of reflections from aluminum and lead foils. Such an effect was not observed in case of silver. In addition, the integral breadths of X-ray reflections from splat-cooled aluminum and lead were not significantly different from those recorded for the annealed metals. The analysis was therefore continued only for silver where the X-ray line broadening was appreciable. The pure diffraction broadening, B, was evaluated for each X-ray reflection (hkl) from silver from the observed, B, and instrumental, b, breadths with the aid of each of the three equations due to Scherrer,5 Anantharaman and Christian,6 and Warren and Biscoe,7 respectively: Bs= B-b BAC=B- b2/B Table I gives the values of particle size, 71, the lattice strain, E, arrived at by the use of the following well-known relations and on the assumption that all observed diffraction broadening could be attributed to lattice strain or particle size, respectively: E = 1/4 cos ? n= B cos ? where A is the wavelength of X-radiation and 0 is the Bragg angle. As no significant peak shifts or asymmetry could be detected in the profiles from the foils, the possibility of any significant contribution due to twins or stacking faults was ruled out. The absence of faults is by no means surprising since pure silver is known to develop stacking faults only on severe deformation and the stacking fault densities recorded so far for even silver filings have been extremely low.&apos; The very low values for percentage mean deviation from the mean value for the particle size in Table I strongly suggest that all observed broadening in splat-cooled silver can be attributed only to small particle size. This conclusion receives further support from the lowest mean deviation recorded for data computed from the Scherrer equation based on Cauchy profiles that are considered characteristic of particle size broadening. Further analysis for separation of particle size and lattice strain effects was considered unnecessary in view of the very large mean deviations obtained for strain values and also the earlier results suggesting absence of even detectable strain in metals and alloys quenched from the melt. It is to be stressed in this connection that the particles are actually grains and not cells formed by walls of high dislocation density usually encountered in deformed samples. As such, the absence of strains is not surprising. The present results are probably the first to record X-ray line broadening due only to small particle

Jan 1, 1970

By Y. H. Liu, R. Kiessling

The chromium, iron, and tungsten borides have been treated with ammonia at different temperatures. They are attacked, forming metal nitride and boron nitride, and the results are summarized in the tables. In the tungsten-nitrogen system a new phase has been observed, closely related to the known ß phase. THE present investigations were begun to determine whether any ternary phases exist in the transition metal-boron-nitrogen systems for the metals chromium, iron, and tungsten. Attempts to prepare such phases were made by using the borides of the metals as starting materials and ammonia as the nitriding agent. Although no new ternary phases have been found to exist, the results may be of some interest with regard to the technical use of the borides. General Procedure A steady stream of dry ammonia was passed through a silica reaction tube, the central part of which was kept at the reaction temperature while its ends were water-cooled. Weighed amounts of the borides were placed in a silica or porcelain boat and heated at different temperatures for a period of 10 to 24 hr. The boat was then rapidly removed from the reaction zone to the quenching zone, the water-cooled end of the tube, by means of a simple magnetic device. The nitrogen content of the products was determined by the increase in weight of the specimens, and the phase analysis was carried out by X-ray methods. For this analysis a Guinier-type camera, constructed at this Institute, was used with a bent, ground quartz crystal monochromator. The general reaction, which occurred in all the experiments, may be summarized as: metal boride + nitrogen -* boron nitride + metal nitride For the higher temperatures pure metal was formed instead of metal nitride. It is sometimes difficult to Discussi detect boron nitride among the reaction products by X-ray methods. Prolonged exposures of some specimens showed, however, that the strongest reflections of boron nitride were present. Additional evidence for its presence was given by the increase in weight of the specimens after nitriding. This increase was always greater than that corresponding to nitride formation only and was often in close agreement with the formula given above. Finally, a white powder, which was shown by X-ray methods to be boron nitride, was left if the reaction products after nitriding Fe,B at 448°C and FeB at 768°C were dissolved in diluted sulphuric acid. Ch rom iu m - Boron - N itrogen Five phases have been found to exist in the Cr-B system,&apos; , and all were used as starting materials. Investigations on the Cr-N system have shown the existence of two nitrides with ideal composition Cr,N and CrN.".&apos; * The results are summarized in Table I. All the borides are attacked and decomposed into chromium nitride and boron nitride, and the kind of nitride formed depends only on the temperature and not on the boride used as starting material. The lowest reaction temperature, however, is different for the different borides. Thus the 6 phase begins to react at about 735 "C, the r phase at about 800°, the S phase at about 900°, the 7, phase

Jan 1, 1952

By John B. Campbell, George G. Binder, Loren H. Jenks

Conventional methods of producing crude oil generally leave in the depleted reservoir 1 to 3 bbl of oil for every barrel brought to the surface. This paper describes a field test which explores the possibility of using gas-driven liquid propane to improve oil recovery efficiency. Laboratory theoretical and experimental studies leading to the field test indicated that low residual oil values could be obtained using limited amounts of propane driven by gas. The field test involved (I) repressuring the reservoir to the vapor pressure of liquid propane, (2) injecting the liquid propane, and (3) injecting dry natural gas to drive the propane and oil to the producing wells. Considerable preliminary work, including new drilling, work-overs, and a pressure survey was necessary. During the test, oil production rates have averaged about nine times the final primary rates. The field average GOR is still below the pre-test value. Oil recovery to date is 112,000 STB. About one-third of the 143,-000 bbl of propane injected has been produced to date. Results of the C-2 block test are encouraging and larger, more definitive field projects ore indicated. INTRODUCTION The cost of finding new crude oil reservoirs continues to increase. Today the oil industry is drilling more and deeper wells and making fewer big discoveries. Nevertheless, the demand for oil and oil products increases each year. It is natural that oil companies, faced with this situation, concentrate on recovering more of the oil existing in our known crude oil reservoirs. There is room for much improvement. For every barrel of oil brought to the surface by present day methods of producing crude oil, generally 1 to 3 bbl are left behind in the depleted reservoirs. The "unrecoverable" oil in petroleum reservoirs is largely "trapped" by capillarity. Since flushing with a solvent is exceedingly effective in combatting oil loss due to capillarity, much effort in this direction has been made in recent years1,2,3,4,5. Liquefied petroleum gas (LPG) has been suggested as a relatively inexpensive. abundant, easily recoverable solvent for crude. Some operators have observed striking responses in oil recovery at production wells offsetting input wells in LPG storage reservoirs6,7,8. In spite of the low unit cost of LPG, however, it is uneconomic in general to inject a volume of LPG into a reservoir to remove a like volume of oil. A modification of solvent flushing in which a limited quantity of liquid propane is gas driven through a reservoir appears capable of recovering much more than 1 bbl of oil per barrel of propane injected. Also, most of the propane injected should be recoverable for sale or re-use. Since such a process could well have widespread and profitable application, The Carter Oil Co. is making an extensive evaluation of the technique&apos;s possibilities. Laboratory development of the gas-driven propane recovery technique was sufficiently encouraging to justify testing in the field. Since 1952, the Production and Research Departments of The Carter Oil Co. have cooperated in a field test in the C-2 Block leases of the

Jan 1, 1958

• The Venezuelan Trade Mission to the United States announced that Bethlehem Steel Corp. will begin exporting iron ore from its El Pao concession, south of the Orinoco River in Venezuela, in about three months. The ore will be transported by rail from the mines to barges on the Orinoco and transshipped to ore vessels at the coast for shipment to the Sparrows Point, Md., plant. The Latin American business men warned that projected increases in the United States tariff on petroleum imports from Venezuela would force that country into bilateral trade agreements with other countries and would mean drastic curtailment of Venezuelan imports from this country. •Bethlehem, South American Gold and Platinum Co., and U. S. Steel are investigating the possibilities of securing American foodstuff for their South American mining camp commissaries through the International Basic Economy Corp. IBEC buys in quantity to supply its subsidiary companies operating in Venezuela and Brazil. The mining companies will rid themselves of this burdensome task as well as realizing a saving from the bulk purchases of IBEC. •Oliver Iron Mining Co. has begun construction of a fine ore and taconite agglomeration plant at Virginia, Minn. It is expected to be ready in six months. The plant will be used to experiment with the making of clinker cakes and egg-sized lumps by sintering machines and nodulizing kilns respectively; about 1 million tons per year will be produced. • Roof pinning has been adopted at the iron mines of TCI, near Birmingham, to support overlying strata as mining progresses. Favorable results have been obtained in that dilution of the ore has been reduced by 50% which is attributable to this method of supporting the roof. •An American mining engineering team has gone to Turkey for a two-year assignment assisting Turkish government agencies in the $45 million ECA development, mechanization, and construction of cleaning plants for the Zonguldak coal field, 200 miles east of Istanbul on the Black Sea. The group consists of James Beeley, John E. Good, John S. Lambright, David Renshaw, and Charles R. Weir, all of the Paul Weir Co. •Arthur F. Taggart describes a new way of training engineers by emphasis on broad, basic engineering courses on page 460 of this issue. •Lawrence T. Tierney, chairman of the National Bituminous Coal Advisory Council, released a report stating that the increase in oil imports since the latter part of 194$ has caused significant damage to the U. S. fuel economy. It has reduced the strength of and employment opportunities in the coal, domestic petroleum, and transportation industries, as well as in related service and supplier fields. •Women, camels, and donkeys are the beasts of burden of the Sahara, according-to the UNESCO World Review. •Increased demand for magnesium sheet in airplane construction ana other phases of the national security program have led Alcoa to establish a sheet magnesium rolling division at its New Kensington, Pa., works which will begin operation shortly. Novel prospecting methods being used by the USGS in its search for uranium include: shock-mounted instruments in light trucks,. Geiger-counter probes lowered into augur holes, and experimental airborne prospecting.

Jan 4, 1950

By B. S. Gottfried

A generalized mathematical model is presented, which describes the thermal recovery of oil in linear systems with convective external heat loss. Three-phase fluid flow, conduction-convection heat transfer, chemical reaction between oxygen and oil and aqueous phase change are included, making the model applicable to a variety of thermal recovery processes. The complexity of the model requires that numerical solutions be obtained with a digital computer. The numerical approximations of the partial differential equations are presented and the algorithm is discussed in detail. The analysis is applied to the detailed simulation of a forward-combustion laboratory tube experiment. The results of the simulation exhibit with reasonable accuracy all of the principal thermal and bydrodynamic characteristics observed in the laboratory (i.e., the propagation of a combustion zone, a steam plateau, and oil and water banks). Numerical variations in the parameters appearing in the external heat-loss term, the aqueous phase-change term, and the Arrhenius combustion term are examined, and their effects on the predicted temperature profiles, oil and water production histories, and the air-oil ratio are presented. In spite of an oversimplification in the chemical reaction mechanism and the considerable computer time required to obtain solutions, the model represents a major advance in the ability to simulate the phenomena observed in thermal recovery experiments. INTRODUCTION Thermal oil recovery refers to a class of recovery processes where heat is supplied to a reservoir to provide the necessary expulsive energy. This thermal energy can be supplied externally as steam or hot water, or it can be generated in situ by forward or reverse combustion. In either case, however, thermal recovery processes are charac- terized by the simultaneous flow of two or three fluid phases in a variable - temperature field, accompanied by possible chemical reaction or phase-change effects.2-5, 7- 10, 14,16-18,20-22 Although a physical understanding of the thermal recovery processes is far from complete, it is possible to construct mathematical models which describe approximately all of the principal physical and chemical phenomena. However, attempts to solve such models, even with high-speed computers, involve formidable mathematical difficulties. Consequently, theoretical solutions have been obtained only for idealized cases in which important physical phenomena are neglected. For example, consider the process of forward in situ combustion. All such theories which have been developed consider only certain aspects of the process, such as heat transfer, 2-4,8,9,l6,l8 heat transfer with phase change,10 heat transfer with chemical reaction,7 or the hydrodynamics of three-phase flow.21 A general theory including all of the above phenomena has not been developed to date. This paper presents a unified theory of thermal recovery processes in linear systems. A mathematical model is developed which explicitly includes conduction-convection heat transfer with convective external heat loss, chemical reaction between air and oil, aqueous phase change, and the hydrodynamics of three-phase flow. A system of equations is developed which can be solved numerically on a high-speed digital computer, resulting in predicted temperature, pressure, and saturation histories in space and time. The model allows a more detailed simulation of thermal recovery tube experiments than had previously been possible. THEORETICAL DEVELOPMENT Consider the linear flow of gas, water and oil in a homogeneous porous medium. Assume that the oil will react with gaseous oxygen, and that mass is transferred between the water and gas phase by evaporation or condensation. In the absence of hydrocarbon phase change, intraphase diffusion,

Jan 1, 1966

By R. D. Mollison, C. F. Fogarty

Sulfur is widely distributed in nature. It is present in the earth&apos;s crust, the ocean, the meteorites that come to us from cosmic space and in practically all animal and plant life. According to Clarke,9 the earth&apos;s crust contains 0.06 pct sulfur. Large quantities of free or combined sulfur are found in coal, natural gas and petroleum. Mineral waters contain sulfates and hydrogen sulfide. Sulfur is rather plentiful in the crust of the earth; however, only under special circumstances can it be produced profitably. Sulfur is one of the cheapest raw materials used by industry; and, therefore, the economic feasibility of a given deposit is strongly dictated by the law of supply and demand on local as well as world-wide levels. The forms which are commercially important are elemental sulfur or brimstone, and the sulfides such as pyrite (FeS2), pyrrhotite (FenSn+1), chalcocite (Cu2S), sphalerite (ZnS), and galena (PbS); the sulfates such as gypsum (CaSO4,2H2O), anhydrite (CaSO4), and kieserite (MgSO4,H2O). Elemental Sulfur Elemental sulfur is found in many localities, generally in solfataras and gypsum type deposits. The solfatara deposits are found commonly in the neighborhood of active or extinct volcanoes as in Italy, Japan and Chile, or fumaroles associated with mineral springs such as the Mammoth Hot Springs in Yellowstone Park. Here the sulfur is deposited in tufas or other porous host rocks. This type of sulfur deposit probably results from the oxidation of hydrogen sulfide or the reaction of hydrogen sulfide with sulfur dioxide. Most of the world&apos;s supply of elemental sulfur comes from the gypsum-type deposits. Here the mineral occurs as either crystalline or amorphous sulfur in sedimentary rocks in close association with gypsum and limestone. This association is characteristic and occurs in almost all the great gypsum beds of the world, although sulfur is not always present in quantities of economic importance. Various theories have been advanced to account for this association. Bischof5 suggested that the sulfur came from hydrogen sulfide which resulted from the reduction of calcium sulfate by carbon or methane in accordance with the following reactions: CaSO4 + 2C= CaS + 2CO2 CaS + C02+ H2O = CaCO3 + H2S CaSO4 + CH4= CaS + C02+ 2H20 2H2S + 02= 2H20 + 2S All of the sulfur-bearing domes on the Gulf Coast have calcium sulfate in great quantity in the cap. They all show the presence of hydrocarbons. The oxygen for the final reaction could have been supplied by circulating ground waters. The principal objection to this theory is that temperatures of 700° to 1000°C are needed to reduce the sulfate to sulfide with carbon compounds. The geologic evidence is that the temperature of the sulfur-bearing domes of Texas did not exceed 100°C. Proponents of the theory say that geologic time or a catalyst replaced temperature. According to another theory the sulfur in the salt domes is the result of bacterial action. Sulfate reducing bacteria have been detected in sulfur cores and in the formation water issuing from salt domes. It has, therefore, been suggested that these bacteria converted the sulfate to sulfide which subsequently was converted to elemental sulfur.

Jan 1, 1960

By R. E. Miner, J. K. Jackson, D. F. Gibbons

Internal-friction measurements were made during isothermal aging treatments of 18 pct Ni maraging-steel wires between 420° and 612°C. A sharp initial drop in the internal-friction level was interpreted in terms of a rapid dislocation recovery reaction. The rate of the recovery was found to be independent of temperature. Truncation of the recovery reaction was apparent in those systems that exhibited the rapid age-hardening characteristics of the maraging steels. It is proposed that this initial hardening response is the result of a low activation energy preprecipitation reaction involving molybdenum. A gradual rise in the internal-friction level at longer aging times was associated with the precipitation of a molybdenum-containing precipitate. CONSIDERABLE research effort has recently been devoted to the mechanisms responsible for the high strength and toughness of 18 pct Ni maraging steels. These bcc martensitic alloys are found to harden during aging at temperatures between 400° and 600°C. The aging response is very rapid with more than half the total hardness increase occurring within the first few minutes of aging, Fig. 1. Precipitate particles have been observed in the later stages of aging by a number of investigators.&apos;-&apos; While the identity of the precipitates remains the subject of some controversy, one or more of the intermetallic compounds, Ni3Mo, Ni3Ti, and Fe2Mo, are almost certainly involved. Heterogeneous nucleation of precipitates at dislocations has been noted8 and cobalt is believed to enhance the formation of fine, homogeneously distributed particles by lowering the solubility of the alloying elements in the martensitic matrix.3,7 Transmission electron microscopy studies of the initial hardening behavior have not been fruitful. Strengthening mechanisms based on atomic ordering have not been generally supported by X-ray and neutron-diffraction experiments.9 In the present investigation, the aging reaction was studied using isothermal-aging internal-friction measurements. The marked sensitivity of internal friction to short-range diffusion and precipitation processes has provided a convenient tool for the elucidation of the strengthening mechanisms operative in the maraging steels. EXPERIMENTAL PROCEDURE An upright torsion pendulum was used to measure the internal friction of several maraging steels during isothermal aging. The pendulum was placed in an atmosphere of helium at a pressure slightly less than atmospheric. To permit measurement of internal friction during the first minutes of aging, the specimens were rapidly heated by passing a current through them in a manner similar to that described by Ang and Wert.10 Thermal gradients in the specimen were largely eliminated by using specially designed specimen grips11 which produced temperature variations of less than 1 pct over 90 pct of the specimen length and less than 3 pct over the entire length at aging temperatures up to 620°C. A proportioning strip-chart program controller was employed to maintain constant specimen temperature during treatments of up to 36 hr duration. A number of vacuum-melted laboratory heats having compositions near that of a typical commercial 18Ni-7Co-5Mo-0.4Ti alloy were investigated. The amount of cobalt was varied from 0 to 7 wt pct in five of the heats. Either molybdenum or titanium was omitted in the remaining two heats. The alloy desig-

Jan 1, 1967

By D. I. Bardos, Paul A. Beck

The 1100°c isothermal, sections of the V-Fe-Si, V-Co-Si, and V-Ni-Si systems were studied at silicon contents between 0 and 40 at. pct. The single-phase fields in the 30 and 50 at. pct Mn sections of the 1100°C tetrahedron of the V-&apos;Wn-Fe-Si system were also determined. The direction of extension of the elongated O, R, D, and a-Mn Phase fields suggests that the stability of these phases is determined largely by the electron concentration. The peculiar shape of the above ternary a phase fields, as well as of the a phase fields in the V-;Mn-Si and Cr-MTZ-Si systems is accounted for on the assumption that in manganese-(iron-, coball-, nickel-) rich alloys silicon atoms do not exclude d electrons , while in alloys low in the above components they do. This assumption also leads to the expected electronconcentrations for q and ß-Mn phases formed by transition metals with aluminurn. In earlier work it was shown that in ternary alloy systems of transition elements the a a and certain other phases with complex structure, such as the p and R phases,3 form elongated phase fields extending in a direction corresponding to a constant electron concentration. Recently similar behavior was observed in manganese-rich ternary ß-Mn solid solutions with another transition element and with silicon, germanium, or tin,4 confirming earlier indications3 that ß-Mn is also an electron phase. The alloying behavior of silicon in these manganese-rich alloys sug- gested that the four outside electrons of silicon participate in the bonding and that the predominantly d-like bonding electrons are not excluded from the silicon sites. Presumably, some of the normally unoccupied 3d states associated with the silicon atoms are in these alloys lowered to the Fermi level;4 thus silicon behaves as if it, too, were a transition element. The manganese-rich boundary of the a phase in the V-Mn-Si system,4 as well as in the Cr-Mn-Si sys-tem,4,5 extends approximately parallel to the ß-Mn phase boundary, corresponding to the transition ele-mentlike behavior of silicon described above. However, at lower manganese contents (i.e., in the high-vanadium or -chromium region) the a phase field in both ternary systems mentioned extends in a direction roughly perpendicular to that of its manganese-rich boundary, a phenomenon that is apparently inconsistent with the behavior of silicon in the manganese-rich alloys. A similar, although somewhat less pronounced, extension of the a phase occurs also in the high-vanadium (low-iron) region of the V-Fe-Si system at 1175C, but reportedly not in the V-Co-Si or V-Ni-Si systems at the same temperature.5 The present work was undertaken to investigate in more detail the extension of the a phase (as well as of other electron phases that may be present) in the last three systems and to elucidate this phenomenon, which has not been satisfactorily explained previously. EXPERIMENTAL PROCEDURES Most of the alloys were melted in an arc furnace, using a water-cooled copper crucible under helium atmosphere. The transition metals were of better than 99.9 pct purity and the silicon used was 99.98 pct pure. Alloys containing less than 20 pct V were induction-melted in recrystallized alumina crucibles under argon atmosphere.

Jan 1, 1967

By T. L. Berger, M. C. lnman, M. F. Rose

AFTER shock loading, mechanical twinning has been observed by several authors1-4 for a variety of fcc metals and alloys. It has been shown2,3 that low stacking fault energy materials deform primarily by the formation of mechanical twins and stacking faults during dynamic loading. Further, Inman, Murr, and Rose2 have shown that a correlation exists between the average hardness and the volume percent of mechanically twinned material in stainless steel. It has been observed in nickel&apos; that mechanical twins are produced during shock deformation if the peak pressure associated with the shock wave is greater than 350kbar. It is the purpose of this work to discuss shock-hardening mechanisms in nickel and to determine to what extent the initial condition influences the final response. The "flying plate technique" was used to generate planar shock waves with peak pressures as high as 710 kbar. The details of the technique5" have been discussed elsewhere and will not be repeated here. The material used in this study was polycrystalline nickel of 99.98 pct purity and had an initial grain size of 0.18 mm. Prior to any deformation, all samples were given a stress-relief anneal of 6 hr at 600°C in a vacuum furnace. After annealing, the initial condition of the samples was changed by cold rolling individual samples from 0 pct to a maximum of 80 pct reduction in thickness. This provided samples with controlled initial histories for shock deformation. Immediately after shock loading, the specimens were slowed and quenched by suitable arrangement of buffer material and water bath. This technique minimized specimen damage and the effects of shock heating on the samples. Since deformation twins in high stacking fault energy fcc metals are only produced at high stress levels, the initial defect configuration prior to mechanical twinning should greatly influence the number of twins formed. In fact, Zukas and Fowler7 have found that prestraining in iron and steel greatly suppresses the formation of mechanical twins during the shock deformation process. Following the methods of Warren and warekois8 and Cohen and Wagner,9 X-ray diffraction profile analysis was performed to determine the incidence of stacking faults and mechanical twins in the deformed nickel. Analysis was made on samples in the annealed, cold-rolled, shock-loaded, and cold-rolled—shock-loaded states. The estimated accuracy of the peak position measurements is *0.01 deg in 2?. Therefore the accuracy in the measurement of the relative peak shifts between the (400) and (222) diffraction line profiles is on the order of *0.04 deg in 2?. None of our measurements indicated peak shifts greater than 0.04 in 28. This would correspond to a fault density of -1 pct and sets the limit on the sensitivity of our instrument. Similarly, analysis of the shift in the center of gravity of the diffraction line profiles yields the minimum measurable value of the twin fault probabilitya to be -0.002. Fig. 1 shows mechanical twinning in nickel shock-loaded to 400 kbar. In this photograph, fault intersections are clearly visible. The thickness of the individual fault lamellae was determined from the image widths of their lines of intersections by the

Jan 1, 1968

By A. Rosenzweig, M. M. Karnowsky

The generalized binary diagram of the Au-Sn-Pb system is presented. The chief characteristic is the pseudobinary between lead and AuSn. On the high-gold side of the pseudobinary, four reaction isotherms were found at 363°, 274°, 225°, and 204°C. On the low-gold side of the pseudobinary, three reaction isotherms at 277°, 205°, and 176°C were found. A vertical section from the eutectic solder composition to gold was developed from the isothermal sections generated. METALLURGICAL problems arising from the intentional or accidental formation of Au-Sn-Pb alloys in soldering applications have indicated a need for information on the phase equilibria in this ternary system. The literature indicates that a complete diagram presenting this information has not been prepared. Even the recent excellent work by prince&apos; entitled "The Au-Pb-Sn Ternary System" actually extends only to the AuSn or 50 at. pct Au range. There are more events in the 50 to 100 at. pct Au than in the less than 50 at. pct range. This article by Prince furnished much guidance in preparing this report. Initial efforts with the isopleth from the eutectic solder composition 61.9 wt pct Sn-38.1 wt pct Pb and 0 to 90 wt pct Au indicated that extensions of the work to the whole of the diagram (even if in less detail) were necessary to understand this system. In undertaking the construction of such a diagram, this study used differential thermal analyses (DTA) and metallography with verification and identification of phases by electron microprobe analyses. EXPERIMENTAL PROCEDURE The procedure began with the development of a cell which would be unreactive with lead, tin, and gold, retain its strength to 1100°C, exclude oxygen, and also furnish a suitable well for insertion and protection of a thermocouple to monitor temperature changes in the material. Such a cell would make it possible to reuse the sample should a repetition of determination be desired. Fig. 1 is a photograph of two such quartz cells as finally developed. The specimens have been run many times. The cell is made up of an inner sample bucket and an outer capsule with a thermocouple well which the sample surrounds. The DTA unit was an assembly devised from available instrumentation. The sample holder was a 3-in.-long cylinder of nickel, 2 1/2 in. in diam, fitted securely in a vertical tube furnace. Two holes 7/8 in. in diam were symmetrically located to receive the quartz cells. A dummy cell with nickel powder was used as the reference. The absolute temperature was recorded with a Pt/Pt 10-pct Rh thermocouple with an automatic Kaye ice bath compensator. (Calibration indicated the compensator to be accurate to better than ±0.5° over the 100° to 1000°C range.) The absolute temperature was measured in the sample and recorded on an L&N mul-tirange recorder with a full-scale display of 1 mv and automatic ranging of 99 mv. The differential signal between the sample temperature and the reference temperature was amplified with an L&N microvolt amplifier and recorded on an L&N Speedomax G recorder. Since two charts were obtained, the chart speeds were equalized and each event was noted on the differential chart, and the temperature at that time was obtained from the temperature record.

Jan 1, 1969