Search Documents

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.' When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.' It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By C. M. Nickerson

It is apparent that repressuring of the oil measures is becoming increasingly important to the oil industry, and is a matter that warrants the best efforts of the petroleum engineer charged with applying this method of operation to a producing property. Considerable attention has been directed to repressuring in various California oil fields, such as Dominguez and Seal Beach, which have served to sell the more progressive operator on this idea and also to keep him sold. The projects that have received most attention are in comparatively young fields where the fluid levels are high, the wells, perhaps, still flowing, where the wet gas production is of considerable volume, and where there is vital need of immediate conservation of gas, which otherwise would be blown to the air. The new State of California Gas Law, which prohibits the waste of gas, has served to interest the oil industry in means of conserving the gas that is now being blown to the air because of lack of markets. This vitally affects the operator in the older, well-depleted oil fields of the state, because in many cases he has a limited market for gas, on account of the flush production from the more active oil fields. While the waste of gas is relatively small in these older fields, such as the Midway-Sunset area, it now attains considerable importance, since under the new State Gas Law it must be put to some bcneficial use. Repressuring in the older fields of California has not received the attention of the petroleum engineers that is warranted by the present situation. This paper was prepared with the view of presenting the salient features connected with repressuring in the well-depleted oil measures of the older fields, and to show what results have already been obtained in these fields by injecting the unmarketable gas into the sands, particularly in the Midway-Sunset field in the San Joaquin Valley of California. Other projects in the older fields of the state offer some supporting data in this connection, such as the Shields Canyon and the Brea Canyon fields. Gas Storage and RepressuRing On account of the lack of market for a large portion of the dry gas produced in certain of the older, well-depleted oil fields of California, the

Jan 1, 1930

By F. M. Drake

IN this paper I propose to describe a plant which I lately erected for the Mount Stewart Lead and Silver Mining Company of Leadville, New South Wales, Australia. I am indebted to Mr. W. F. Burrow, of the Roads and Bridges Department of New South Wales, for the drawings which I present herewith, he having reduced and assembled them from my working drawings. The works are situated on a sloping hillside, but sufficient fall mas not available to have the furnace as high as desired, and at the same time have a good slag-tip and sufficient depth on the ore-floor to store a supply of ore and flux. The ore is delivered on the ore-floor (which is of the full width of the furnace-building, and extends back into the hill a distance of seventy feet) by two overhead tramways (not shown in the drawings), one on each side. From these the ore-mixture is made up on one side, while it is being taken to the furnace from the other. The fuel also is delivered by these tramways. The fluxes are stored on a floor directly at the back of the boiler and engine room. The boiler is a Cornish one, 6 feet 6 inches in diameter by 25 feet long. Its flue is 3 feet in diameter and does not contain Galloway tubes. The working-pressure is 40 pounds per square inch. The engine is an old-fashioned one, with a cylinder 16 inches in diameter by 30 inches stroke. Both the engine and boiler had been part of the plant of a defunct gold-mining company. They were very extravagant in their consumption of fuel. The blast is supplied by a rotary pressure-blower, of the Baker pattern, made in England. It has a capacity of 60 cubic feet per revolution. The furnace, which has several novel points, is shown in detail in Figs. 1, 2 and 3. The jackets are of cast-iron, and are higher than those generally used. They are different, too, in that the feedwater inlet is through a hand-hole plate near the bottom. This plate is fastened to the jacket by stud-bolts, and is provided with a baffleplate, which prevents the cooling water from impinging against the inner plate. The outlet is by a goose-neck at the top, which dis-

Jan 1, 1893

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By H. W. Reid

One of the outstanding features of the year was a further marked decline in the footage drilled. This is estimated at 169,000 ft., as against 218,000 ft. for the previous year, and 372,500 ft. in 1930. Owing to repair work and improved production methods, there was an increase of about 4.25 per cent in the amount of oil won, the production being estimated at 10,160,000 bbl., or an increase of 400,000 bbl. over 1931 and nearly 750,000 bbl. more than in 1930. (See Table 1.) At the end of November there were 28 rigs in operation. During the first 11 months of the year 54 new wells were started; the average depth of those completed was 2476 feet. Owing to the continued restriction of drilling programs there has been little of outstanding interest in the way of new plant or technique. The use of the acid bottle, for testing the verticality of wells while drilling, has increased considerably, and this is now in use in practically every well except the very shallowest. During the last six months of the year fairly extensive use has been made of electrical coring. The number of wells started in the Colony up to the end of November, 1932, was 1894. The average number of producing wells during the year was 789, or 41.7 per cent of the total. Of these, 214 were flowing wells, 473 pumping, 80 bailing or swabbing, and 22 were produced by air or gas-lift. Although the last category represents less than 3 per cent of the total, there has been a marked increase in the use of air or gas-lift as compared with 1931. During the year there were 16 companies engaged in producing oil, as compared with 14 in the two previous years. In addition to one small refinery which started to operate at the beginning of the year, the five existing refineries worked continuously. At the latter very little has taken place in the way of extensions, except at one in the Parry Lands—Pitch Lake—Point Fortin area, where extensive alterations and additions are in progress, including the building of a deep-water pipe-line pier. When this is completed there will be five loading terminals, all situated in the sheltered Gulf of Paria, or west, coast, capable of accommodating ocean-going tank steamers. There

Jan 1, 1933

By R. H. Wightman, G. H. Adams

In order to secure good results in the prevention of accidents, it is generally recognized that the desire for such accomplishment, as well as the aggressive and constructive action to achieve it, must emanate from the Top Management and permeate successively down through the "Chart of Authority" to the workmen. Several years ago, with the above as a basis and with full support of the Top Management, the Mining Department started a program of selling the foremen and bosses the idea that safety could be achieved and that it was desired and required. Using psychology, persistence and numerous other methods, the foremen and bosses were finally impressed with the idea that "It can be done" and "It will be done." With this in mind, new ideas were brought forth by the foremen and bosses regarding the caving operation and the specific jobs in the operation. These new ideas were taken up in round-table discussions and resulted in certain changes in the undercutting method and the actual drawing of the blocks. These changes resulted in increasing fragmentation of the blocks which prevented the usual hang-up areas in the blocks. With the rock smaller in size and within reasonable reach from the tapping drifts, accidents were prevented in the tapping section. At the same time, an enforced campaign of housekeeping throughout the mine was undertaken with very beneficial results. The foremen and bosses then, in turn, educated and trained the workers themselves to become safety conscious. In so doing, a constant reminder was given on all jobs assigned that the job was to be done safely as well as efficiently. No man is assigned a job who is not qualified for the type of work required. Efficiency and safety go hand in hand. Safety Rules To supplement and aid this safety conscious attitude, certain safety rules applicable to our operation, a modified block caving system of mining limestone, in addition to the established state regulations, were put into effect and enforced. The specific rules referred to above and which will be mentioned below are in most cases simply a means of applying and complying with the very adequate "Mine Safety Orders" issued by the Industrial Accident Commission of the State of California. Some of the safety rules and policies are as follows: All men are required to wear safety

Jan 1, 1950

By B. B. Zavoico

After showing continued and very satisfactory progress until the close of 1931, the oil industry of the Soviet, Union experienced very great difficulties, and since 1932 has not only failed to complete its assigned quotas but has fallen farther and farther behind them, and in fact during 1932 and 1933 Russian production has been below production in 1931. In 1934 the total crude oil production of 169,200,000 bbl. exceeded that of the former peak year, 1931, when 156,100,000 bbl. were produced. The production during 1934 amounted to 78.65 per cent of the plan. The failure to complete the plan has been due to the inability of the oil trusts to develop new fields; the fields that have been producing since 1917 still account for between 75 to 80 per cent of total production. The failure of the Soviet Government to develop new fields has been due to unsatisfactory organization of the geological work, to the extremely slow drilling of wells and their exploitation, and to the very much delayed development of the few areas that have been discovered. The official overestimation of the proven reserves of the country has undoubtedly been an important factor in giving the Soviet industry too much confidence when actually such reserves have been small. The official Soviet estimate of proven reserves of Russia is now placed at 21,000,000,000, bbl., while in fact such reserves, if estimated on a conservative basis, do not exceed 4,200,000,000 bbl., as will be shown later in this review. The refinery branch of the industry also showed unsatisfactory results with a recovery of gasoline, both straight-run and cracked, of only some 16 per cent of the total runs to stills. In fact, the showing of the refineries has been so unsatisfactory that the exports of gasoline have been greatly curtailed from 1933 to 1934, dropping to 10,000,000 bbl. in 1934 from 12,230,000 bbl. in 1933. With the indicated increase in domestic demand, together with but slightly increased refining capacity, the volume of available gasoline for export probably will be reduced to about 6,000,000 bbl. during 1935. The geographic distribution of constructed refineries has been unsatisfactory and the crude oils from Baku had to be transported by tankers

Jan 1, 1935

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

John A. Church, New York City: It requires some courage to appear as a critic of a theory which is not only the fashion among American geologists but is usually presented by them in terms which imply that any other views are an exhibition of ignorance. Still, I am obliged to say that the theory of lateral secretion as it is stated in this and other writings of Mr. Emmons and other geologists has not added much to our real knowledge or clearness of view. In the earlier and less developed stages of the theory, when it was used as Sandberger used it, to show that certain veins were probably derived from the rocks in which they lie, or which are adjacent, it was valuable in pointing us to an immediate source of ore-deposition. When we are driven to assume the existence of undiscoverable rocks at an unknown but certainly a considerable distance and in an unknown direction from the vein, I do not see that we have improved upon the despised " unknown source in depth " with which our ignorance has been covered so long. The new theory may suffer from adolescence, and these points map be cleared up by further study, but I speak of it as it is. Differentiation in a magma, by which a metal is concentrated in one member of a series of outflows, may explain why certain ores have favored a given locality with their presence; but it is not a necessary precedent to ore-formation. Concentration in the source of supply cannot be a requirement, for the forces that have been able to take up four or five tons of gold from an extensive body of rock must be able to collect four or five thousand tons of lead, copper or nickel from a proportionately more extended body of rock. That is to say, concentration is no more essential for these metals than it is for gold. In fact, differentiation, as it is now explained, is not an advance upon old ideas, but a retreat from them. It was noticed long ago that violent eruptive phenomena, however long continued, died away in solfataras; and when a vein came to be looked upon as an extinct solfatara the inference was ready that veins are eruptive in the sense that the solfataric waters collected the metals from the unerupted residue of the magma and carried them to the veins. The early views carried differentiation further than the modern school.

Jan 1, 1894

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways, and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard-rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed. Mining, from exploration through refining, is essentially a process of sorting in which the payable mineral, or metal, is progressively separated from the other constituents of the earth&apos;s crust with which it was originally associated. This takes place more distinctly at each step of the operation. What is it that determines the degree to which sorting should be carried out at each of the several steps comprising a whole mining operation? The formal answer is that degree of sorting at each step which results in the lowest overall cost for the complete separation. In practice, individual steps are chosen from those available in current technology, each of which effects a degree of sorting such that the quantity of material which must be sorted in the succeeding step is economically acceptable. It follows that any new technological development has repercussions throughout the whole mining operation and, more important, that the solution to excessive costs in any one step of the operation may lie not in improving the costly operation itself so much as in increasing the degree of sorting preceeding that operation. This concept, particularly in relation to deep-level mining of thin, tabular gold-bearing reefs in South Africa, is discussed here, and the most recent results achieved in the development of hard-rock cutting machines for stoping more selectively than is possible with explosives are presented. Deep-Level Mining Deep-level mining involves operations which are either not encountered, or are of only trivial importance, in near-surface mining. Near-surface, the major operations are those of rock breaking, transport, and milling. In deep-level mining, hoisting, environmental control, and strata control assume major importance. Some idea of the relative magnitude of these operations may be gained by comparing the separate amounts of energy which are required, or which must be controlled, to effect the various operations when, say, mining a tabular deposit 40 in. thick at 8000 ft below surface, Table 1. It is true that the costs of handling a given quantity of energy are not the same for each operation. Nevertheless, Table 1 does emphasize the fact that the operations of hoisting, strata control, and environmental control are of unique and major significance in deep-level mining. In particular, hoisting and environmental control place a heavy load on the reticulation system of the mine—the shafts, haulages, and airways. Typically, a new, deep gold mine with an annual revenue of about $35 million requires a total capital expenditure of about $140 million of which some $100 million is invested in developing and equipping this reticulation system. The ratio between annual turnover and capital invested of about one-quarter is exceptionally low, and it typifies the poor utilization of capital by the current technology of mining hard rock at depth. The average thickness of the reefs in the new South African goldfields varies from 10 to 30 in.,l and even in the thicker reefs the gold is often confined within a small fraction of the nominal thickness. Nevertheless, it is universal practice to mine these reefs at a stope width of about 40 in. or more, so that the quantity of rock broken in the stopes and hoisted out of the mine is between two and ten times the quantity of rock actually carrying a significant amount of gold. The reason for the adoption of such excessive stope widths is to be found in the method of rock breaking by drilling and blasting. The only free surface to which a blast hole can break is the stope face. It follows2 that each hole cannot have a burden in excess of the height of the free face if it is to break satisfactorily. To

Jan 1, 1971

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By H. R. Cooper, T. S. Mika

T. S. Mika (Department of Mineral Technology, University of California, Berkeley, Calif.) - Dr. Cooper&apos;s attempt to establish a correlation between process behavior and operational variables on the basis of a statistical analysis after imposing a reasonable process model is a very commendable improvement on the use of standard regression techniques. However, it must be recognized that the imposition of a model has the potential of yielding a poorer representation if its basic assumptions or mathematical formulation are invalid. It appears that at least two aspects of his treatment require some comment. First, the limitations on the kinetic law where xta represents a hypothetical terminal floatable solids concentration (cf. Bushell1), should be mentioned. Most current investigations2-9 appear to utilize the concept of a distribution of rate constants rather than a single unique value, k, to describe flotation kinetics. A distributed rate constant is certainly a more physically meaningful concept than that of a terminal concentration. The study of Jowett and safvi10 strongly indicates that xta is merely an empirical parameter, whose actual behavior does not correspond to that expected from a true terminal concentration. Rather than being a strictly mineralogical variable, as Dr. Cooper&apos;s treatment implies, it apparently represents the hydromechanical nature of the test cell as well as the flotation chemistry. The extension of batch cell kinetic results to full-scale continuous cell operation is a suspect procedure if the effect of such nonmineralogical influences on x,, remain unevaluated. There is evidence that introduction of a terminal concentration is necessitated by the inherent errors which arise in batch testing and are eliminated by continuous testing methods.&apos; Possible lack of validity of the author&apos;s use of Eq. 1 is indicated by two unexpected results of the statistical analysis of his batch data. The first is the apparent corroboration of the assumption that the rate constant, k, is independent of particle size, i.e., of changes in the size distribution of floatable material. This assumption directly contradicts numerous results 2,4,11-l8 for cases where first order kinetics prevailed and ignores the phenomenological basis for the analysis of flotation in terms of a distribution of k&apos;s. It must be recognized that, if the rate constant is size dependent, the lumped over-all k would be time dependent; Eq. 1 would then no longer be valid. Cooper&apos;s x,, is determined by batch flotation of a distribution of sizes for an arbitrary period of time. If the size dependence of k is artificially suppressed, x,, will become a function of the experimental flotation time used in its determination. Upon reviewing the rather extensive literature concerning batch flotation kinetics, there appear to be few instances where constant k and x,, adequately adsorb variations in floatability due to particle size. The second surprising result is the low values of the distribution modulus, n, determined. Contrary to Cooper&apos;s assertion, most batch grinding (ball or rod mill) products yield values of n > 0.6, which increase as the material becomes harder.&apos;&apos; It is likely that the values of n = 0.25 and n = 0.42 for Trials 1 and 2, respectively, are completely unreasonable, and even the value n = 0.54 obtained for Trial 3 is unexpectedly low. Possibly, this indicates inherent flaws in the three trial models considered, in particular the assumed particle size independence of the rate constant, k. The above does not necessitate that Eq. 1 (and the terminal concentration concept) is invalid; it could constitute a good first approximation. However, the qualitative arguments used by Dr. Cooper in its justification are somewhat frail and require verification, particularly since much of the flotation kinetics literature is in opposition. Apparently, no effort was made to test these hypotheses on the actual data; in fact, since they pertain to a single batch test time, his data cannot be utilized to evaluate the kinetics of flotation. To evolve a control algorithm on the basis of this infirm foundation seems a questionable procedure. Another difficulty in his analysis arises in consideration of the froth concentrating process. As Bushel1 &apos; notes, for Eq. 1 to be valid it is necessary that the rate of recycle from the froth be directly proportional (independent of particle size) to the rate of flotation transport from the pulp to the froth, a restrictive condition." Harris suggests that it is more realistic to assume that depletion occurs in proportion to the amount of floatable material in the pertinent froth phase volume (treating that volume as perfectly mixed).12,21,22 The physical implications of

Jan 1, 1968

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By William P. McConnell

At the dawning of the first century of AIME, mechanical handling of bulk materials was largely confined to movement of grain and light mill products by belt and screw conveyors, but grain handling experience inevitably led to the use of the belt conveyor for coal, ore and other heavier materials. In 1891, the first major U.S. conveyor installation for heavy minerals was completed at the Edison, N.J., plant of the New Jersey & Pennsylvania Concentrating Co. Functionally, this plant revealed its grain elevator heritage. Overlooked at the time of design or, perhaps more accurately, not fully recognized, were the dramatic differences between grain and minerals in both operating conditions of the system and the physical characteristics of the material to be conveyed. This inevitably caused problems, but from the ashes of these problems rose solutions. The Edison plant became a proving ground from which came two significant developments by Thomas Robins-the first conveyor belt designed specifically for impact loading and abrasive materials and the three-roll conveyor idler. As an installation with more than 50 conveyors in widths of 20-30 in. and belt centers of up to 500 ft, the plant was a landmark, for it established the belt conveyor as a vital method of trans- porting heavy, abrasive materials.

Jan 1, 1971

By R. N. Singh, A. S. Atkins

One of the most difficult problems associated with modern mechanised longwall mining is the lack of system flexibility to deal with local changes in geology, seam thickness and the face design parameters. As a consequence of system rigidity and the quest for increasing the coal face performance, the percentage extraction in the U.K. is currently below 52%. The paper outlines the current guidelines used in face design which permit coal to be left in situ for various purposes and discusses the strata control implications in extracting subsequent panels in the same and adjacent coal seams. The paper examines the application of strata mechanics to the design of longwall layouts for maximizing .the percentage of coal extraction. Remedial measures include optimizing pillar dimensions, reduction in roof coal left for support purposes by improving the use of available powered support technology and application of thick seam mining methods including sub-level caving and techniques of extracting coal from odd shaped pillars. Case studies are described where coal extraction has been maximized by adopting a new single heading retreat mining system; a shallow seam partial extraction system utilizing, existing heading machines and minimisin8 coal sterilization in pillars by replacing longwall access roadways by goaf scour.

Jan 1, 1984

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,&apos; and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By Maynard H. Jameson

Earlier investigations of the potential-drop-ratio method of electrical prospecting have indicated that under suitable conditions this method is well adapted to the location of formation boundaries in stratified ground. A description of this development was given several years ago by H. Lundberg and Th. Zuschlag.l The curves published by these authors for the potential-drop-ratio variation above a horizontal contact indicated a definite relation of the position of the curve peak to the depth of the interface. The theory underlying this relation was subsequently studied by Z. Mitera in greater detail,&apos; and the theoretical deductions were compared with the results of tank experiments. The investigations available at this writing were confined to studies of horizontal formation boundaries. It is the purpose of this paper to extend the scope of the previous work to the problem of dipping layers. Theory Consider the case of three media of different resistivities, whose interfaces are not parallel. If a point-source is located in one of these interfaces, its images do not lie in a straight line, but on the circumference of a circle whose center is at the hypothetical junction of the interfaces. R. F. Aldredgea determined the relation that exists between the degrees of dip of the two interfaces and the distances between the various images and the point for which the potential is to be found. As seen in Fig. I, three media of resistivities PO, p1, and p2 are involved, and the source I is located at the interface of the media Coo) and (p1). The perpendicular depth of the lower interface is h, 0 is the dip, R is the distance between source I and potential point P, and r is the distance between the images and that point. To distinguish between images lying above the ground interface and those below, the notation "odd" and "even" images will be employed; images below the ground interface will be termed "odd" and those above "even." The following relations govern the distances between either kind of images and the potential point: EvEn Odd Ta — R r1 - [rl] - [RS + 4h(h + R sin 01½ r, = [r] =. [R1 + 4h cos 0)2(h + -R sin 0)1½ ri - [r3] ={r3} [R* + 4h(4 cos2 0 - i)1 (h + R sin 0)l½ r4 = [r4] = [R2 + 4h(4 cos $ cos 30)1 (h + R sin 0)]½ r, — [r4] - [R2 + 4h(4 cos9 R cos 20 + cos 48)2 (h + R sin 01½ I RI + 4h[2 cos 30(4 cos2 0 - I)12 (h + R sin 8)1 ½ rn - [r4] - [R2 + 4hlf(cOs 0)18(h + R sin R)l½ As previously pointed out, the images of the source are on the circumference of a circle. If the angle of dip is 0, the angle measured from the horizontal to the first image is 28; to the second image it is 48, and so on. Since the limit of the reflecting interface is at its outcrop, the last possible

Jan 1, 1946

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946