Search Documents

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By Charles H. Thurman

The data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. Dragline vs. Bucket-line Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 106 gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new 7-cu. ft, bucket-line dredge, costing upward of $250,000, and in operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ Per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These Percentages of operating time are important factors in making a comparison of this kind- The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft- (65 ft. below water, 15 ft. above). A 5-cu. Yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10 gravel 28 ft. deep with bucket line, costin 4¢ Per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ Per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equip-ment, fully depreciated. Dismantling, mov-

Jan 1, 1946

By H. Dykstra

Calculated wellbore pressures were obtained for parameters of radilcs ratio and permeability. In all cases bur two, after-production was allowed to occur for one day. The calculated pressure build-up data were compared with actual pressure build-up data from a condensate well. The paper discusses the comparison, gives reasons for, inability to match calculated (2nd actual data, and presents conc1usions derived from the comparison. INTRODUCTION Considerable information has been published on the decline in wellbore pressure for oil and gas fields resulting from production of fluids. Considerable information also has been published on pressure build-up for oil fields, but relatively little has been published for gas and condensate fields. Perrine' summarized the equations derived for pressure build-up in oil wells and showed how the different methods could be applied. On the other hand, very little theoretical information has been published on pressure build-up in gas or gas-condensate wells.2-4 Tracy,' by pointing out the similarity between the equation describing oil wellbore pressure decline and the equation describing gas wellbore pressure decline, showed how methods of pressure build-up analysis could be applied to a gas well. In analyzing pressure build-up data for gas or gas-condensate wells, it would be very desirable to compare actual pressure build-up data with calculated pressure build-up data. Such a comparison would lead to a better feeling for the quantitative picture of gas-well build-up curves and would help to establish a degree of confidence in a given build-up curve. This paper discusses the comparison and presents conclusions made from it. Calculated wellbore pressures are given for parameters of radius ratio and permeability. In all cases but two, after-production was allowed to occur for one day. The work was done in an attempt to evaluate the reserves of a gas-condensate field. As will be discussed later, it was not possible to make an evaluation. METHOD OF CALCULATION The method used for solving the depletion and pressure build-up behavior for a gas-condensate well was that developed by West, Garvin and Sheldon.5 or the IBM 704 computer program used, it was assumed that liquid condensing out of solution would have only a minor effect on the flow behavior. Therefore, the field was treated as having single-phase flow, with the gas saturation S, remaining constant at unity minus the connate-water saturation Sw. As will be discussed later, this may not have been a good assumption. It also was assumed that oil production could be considered as equivalent gas production by using a conversion factor based on an analysis of the liquid produced. An outer boundary condition of no-flow was assumed. BASIC DATA The data required for the study were reservoir properties, fluid properties and production data. Reservoir properties included the following: thickness h, 179 ft; porosity, 0.194; connate-water saturation, 0.43; gas saturation, 0.57; permeabilities k, 1.0, 0.5, 0.25 and 0.15 md; radius ratios re/rw, 800, 1,000 and 2,000; wellbore radius rw, 5 in.; initial reservoir pressure P, 6,529 psia; and reservoir temperature, 272°F. The selection of permeabilities was based on core-analysis data showing an average air permeability of about 2 md. With a relatively high connate-water saturation, the average effective gas permeability would be about one-half, or less, of the air permeability. The selection of radius ratios was based partly on the observed rapid decline in wellbore pressure during production and partly on the fact that the well was believed to be located in a relatively small fault block. Reservoir fluid properties were obtained from a reservoir fluid study on a recombined sample of gas and condensate. Gas formation-volume factors were calculated from pressure-volume measurements made at reservoir temperature. Gas viscosities were calculated by the method of Carr, et al,G from an analysis of the re-combined sample. These data are shown as a function of pressure in Table 1. The production schedule from the gas-condensate

By Roy E. Dickerson

No important new developments took place during the year 1937 in Cuba. Estimated figures are as follows: Bacuranao field, 100 bbl. per day petroleum; Motembo and Vesubio areas, 120 bbl. per day natural gasoline.

Jan 1, 1938

By Alan Lawley

AS part of a programme of experimental work on single crystals of rhenium and ruthenium, it was found necessary to have the crystallographic angles for these elements. The angles given in Table I were determined to the nearest minute of arc, by Univac Computer. The angle $ between (HKIL) and (hkil) is given by the formula: The angles given for rhenium should be particularly useful in view of the increasing interest in this element. For completeness, angular values are also given for cadmium zinc and magnesium; these form a more complete set of values than those given by Salkovitz.' The assistance of Professor J. Hobstetter and Mr. J. Crozier in the programming of this data is acknowledged. The work is sponsored by the Office of Naval Research under contract No. NONR 551 (19).

Jan 1, 1961

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

By C. E. Webber

The economical recovery of the valuable constituents from the effluent of gas-con-densate wells has developed into a problem of balancing the cost of recovery against the cost of compressing the residual gas back into the formation. A possible method of extracting the gasoline and distillate from the natural gas is by oil absorption at high pressures. In order to design and evaluate an absorption plant, fundamental data on the composition of the coexisting hydro- carbon vapor and liquid phases at various temperatures and pressures are essential. A review of the literature indicated that the necessary data for the design of such plants are lacking. The nearest approach to desired published data is that of Katz and Hackmuth,~ who experimentally deter-mined the composition of the coexisting vapor and liquid phases in a natural gas-crude oil system at pressures up to 3000 lb. per sq. in. and at temperatures from 40' to zoo°F. This paper presents the results of the experimental determination of the equilib-rium distribution of the hydrocarbons methane through hexane between natural gas and a typical absorber oil. The ranges of temperature and pressure chosen were from 33' to r8oUF. and from 100 to 5000 lb. per sq. inch. Materials The absorber oil was a typical naturally occurring, Straw-colored distillate that had previously been steam-distilled to an initial boiling point of 300 F. The physical and chemical properties, including the results of an Engler distillation, are presented in Table I. A large volume of this oil was obtained and it was used throughout the complete set of experiments. Table i.—Properties of the Absorption Oil Gravity .......................... . . 32.5' A.P.1. Molecular weight by benzene freezing- point depression.................. 183 Viscosity, poises; at 100°F........... 0.0a80 At 200°F...................... 0.0102 Composition, PeR Cent Aromatics........ 24.0 Naphthenes..... 36.7 unsaturates,Aromatics...... .I24.00.3 1 Parafins Naphthenes.....36.7 39.o EngLeR Distillation Per Cent /ncg. F. Per Cent Dez. P. Initial boilins rmint.. 300 I 60....... 523 5.................. 402 I 70....... 538 10.................. 421 180....... 557 20.................. 462 90....... 570 30.................. 480 1 95....... 623 40.................. 49 .................1 511 Residue, z .o per cent; loss, 0.3 per cent. See refrence I. The n-hexane was obtained from the Ohio Chemical and Manufacturing Co., Cleveland, Ohio. This liquid had a boiling range of from 149" to 152.6'F., with a density of 0.667 at 60°F. and a molecular weight of 85 by benzene freezing-point depression. The propane, isobutane, wbu-tane, isopentane and n-pentane were ob-ta,ined from the Philgas Department of the Phillips Petroleum Co. Certified analyses of these compounds showed their purity to be in excess of 99.5 per cent and they were riot further purified.

Jan 1, 1941

BECAUSE it is necessary that the powders made for casting have a magistery of salt water, I wish now to teach you to prepare the salt that must form this magistery, for without it these powders would not have the toughness to hold themselves together when they are dry. In short, you take the quantity [119v] of salt that you need to prepare and put it in a rough pot, either baked or, if it suits you better, raw but well dried. This is completely covered with a lid or is luted with well- made moulding clay. Then it is encircled with brick ends at a distance of three dita, like a drying furnace. This space is filled with good charcoal; fire is applied and it is left to stand until all the charcoal is consumed by itself* Then you take that quantity of this burned or rather melted salt which you wish to use for moistening the clay and which you think can be dissolved in the water so that it wd remain very salty. It is boiled in a pot with water and then left to stand. After it has settled, your powder is moistened with it and used for moulding. When you see by testing it that the powder stands up as you wish, it is good. If not, give it some more of this water again and continue until you see that it holds enough. For without this magistery it would return to the dryness that it had before as a powder, and you could not use it without fear that it would fall from the Games. In this way this earth, either natural or artificial, is prepared and made ready, and it is used as the need occurs.

Jan 1, 1942

By P. A. Beck

In the course of work on grain growth in high purity aluminum a simple optical method was developed for detecting the presence or absence of preferred orientation in annealed specimens. The specimens were prepared by grinding, polishing and "deep etching." The etching reagent used for high purity aluminum has been described.* The resulting etch pits produced selective

Jan 1, 1949

Edward Eeller, Baltimore, Md. (communication to the Secretary): Mr. Miller's improved method of the cyanide-assay for copper will, without doubt, be much appreciated by assayers and chemists who are engaged at copper mines and works. The writer, as one who, at one time, had much work of that kind to do, entertains no doubt of its practical value. In enumerating the factors which affect the accuracy of cyanide-titration, Mr. Miller omits to mention time. This I have always considered an essential one; i.e., in order to secure accuracy, I have believed it to be necessary to run the cyanidesolution at the same rate of speed in standardizing as in the titration of the samples. I have accomplished this, without the use of a time-keeper and without noticing the volume of the solution, in the following simple manner: In running the cyanide-solution from the burette, the stream was so regulated, by manipulation of the cock, that it retained its continuity for a distance of about one inch below the orifice, and, below that, broke into individual drops. This means that a constant pressure is maintained at the orifice of the burette, so that, during equal intervals of time, equal volumes of the solution pass through. The stream of cyanide-solution was left to flow in the manner indicated until the blue ammoniacal copper-solution began to show a distinct change in color, after which the cyanide was added by drops at regular intervals until the desired end-reaction. When several burettes are used they should have orifices of equal diameter; otherwise, the timefactor must be considered separately for each. In accordance with Mr. Miller's views, I have always considered the cyanide-method as of very satisfactory accuracy for all copper-assaying in which I did not employ the electrolytic method. It may interest some of my colleagues to know the modified method which I employed some fifteen years ago in making great numbers of copper-estimations on ores and

Jan 1, 1902

By J. W. Ristori, V. R. Garfias, R. V. Whetshel

During the past eight years, in trying to estimate world consumption of petroleum and related products, the authors have been unable to account for all the supplies available in any one year. There has remained at all times a balance, which at first was thought to represent almost entirely additions to stocks in foreign countries. But as this discrepancy continued year after year-over 148,000,000 bbl. in 1937—it became unreasonable to conclude that corresponding additional foreign storage capacity was continuously being made available. It became therefore clear that the balance in question was due to other causes than to additions to stocks. Last year Mr. A. G. White, Chief Economist of the Petroleum Economics Division of the United States Bureau of Mines, pointed out to one of the authors that an unknown and important factor in consumption of petroleum and related products is to be found in the requirements for military purposes in foreign countries. This paper is the result of Mr. White's timely suggestion. There are no reliable data available either on the storage capacity, and therefore oil stocks, or on the petroleum consumption for military purposes in foreign countries. This information is so closely related to national defense that its divulgation is forbidden. One can therefore but surmise as to these facilities and needs in line with the relative strength of the military land, air and sea forces of the various countries. The authors have assumed many of the component factors that go to make the tables herein presented, such as fuel consumption of fighting ships in relation to tonnage and horsepower, gasoline consumption of air fleets in relation to number of planes, and the consumption of petroleum products by mechanized armies; but in making these assumptions they have availed themselves of the advice and counsel of those whose wide experience in these questions make their views authoritative. The opportunities for error in an estimate of this nature are obvious and ever present; to illustrate: The air fleets in Spain no doubt consumed

Jan 1, 1938

By E. H. Crabtree, T. C. King

The ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1½ by 4 by 12 in. and an analysis of 85. pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-100 mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separa- tion was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the nonmagnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1949

By Axel Sahlin

Since the days of the infancy of metallurgical industries, slags of various kinds have been accumulating. Until a comparatively recent date hardly any employment had been found for these waste products, which have had, consequently, little or no value. An exception to this rule is the basic Bessemer slag, the value of which has become universally recognized. It is to-day one of the standard fertilizers of the world, and a price of from $15 to $20 a ton is considered reasoiable for the ground slag, which, especially in Germany, finds a ready market as fast as it is prepared. The slags from puddling and re-heating furnaces have only found vol. xx.—25

Jan 1, 1892

By R. D. Carnahan, J. E. White

ThE use of strain gages in the measurement of microplastic behavior of materials is well-known.'-3 Recently it has been suggested that similar techniques might be useful for determining stress relaation. It is the purpose of this report to comment on the use of strain gages in the measurement of strains in the vicinity of 10"6. We will also discuss observations of an anomalous anelastic behavior apparently associated with small temperature changes, which accompanies the unload portion of a load-unload microstrain test. The key to successful strain determinations at levels below 1 pin. per in. is a good gage-mounting technique and either precise ambient temperature control or a set of matched temperature-compensated gages. The importance of good mounting cannot be overemphasized, for example, as in the use of Eastman 910 contact cement. If the cement layer is not sufficiently thin and properly hardened, it is possible to observe anomalous negative stresses when small loads are removed, which relax back to zero in an orderly way with time. Such anomalous behavior, thought to be due to gage bonding, has been reported in microstrain experiments by Thomas and verbach' who observed a negative strain of -3 X lo-' upon unloading. This kind of behavior severely limits the over-all strain sensitivity which can be achieved in such tests. The relaxation of a small positive strain subsequent to unloading in a load-unload experiment is quite normal, however, and is to be expected. The occurrence of an apparent negative strain is also encountered in those instances where the elasticity of the bonding cement is exceeded—for example 0.5 pct or 5000 pin. for cured Eastman 910. An elastic strain of this magnitude can be encountered during load-unload type testing particularly in higher-strength materials (-150,000 yield strength). During the course of microplasticity studies on pure nickel and nickel alloys,' the authors have made the following observation. In a four-point bending test, two active gages are mounted one on each side of the beam as arms R1 and R z of a conventional strain-gage bridge circuit shown in Fig. l(a). This technique provides two advantages: the sensitivity is doubled because R1 and Rz experience opposite strains and temperature compensation is provided automatically because any ambient temperature change would cause both gages to see a strain of like sign whose signals would cancel in the circuit.

Jan 1, 1964

By J. B. Patton

No academic program of reasonable duration can provide a geologist with all the skills that may be needed for applied work in industrial minerals. However, any curriculum that does not provide background in such basis subdisciplines as mineralogy-petrology, stratigraphy, sedimentology, structure, and geomorphology will leave the practitioner handicapped. Enough geochemistry to understand materials requirements, and sufficient geophysics to use geophysical data, are essential. In addition to purely scientific considerations, the industrial minerals geologist must be able to evaluate economic factors. He may also be faced with legal, social, and political problems in land use, zoning, envil.onmenta1 protection, and reclamation.

Jan 1, 1985

By G. R. St. Pierre, A. Ghosh

In the Si-C-0 system at temperatures of interest in process metallurgy there are four stable condensed phases—silicon, carbon, silica, and silicon carbide (Sic). Silicon melts at 1683oK1 and shows negligible solubility for carbon and oxygen at 1700°K. However, silicon dissolves approximately 1.5 at. pct C at 2500oK.2 Carbon in the form of graphite remains pure and dissolves negligible amount of silicon.' Silica (crysto-balite) melts at 2001°K' and is essentially a stoichio-metric compound. Silicon carbide is a solid and shows negligible deviation from stoichiometry up to approximately 2800oK.2 Besides the condensed phases there is a gas phase

Jan 1, 1970

By Oswald J. Heinrich

At the Baltimore meeting of the Institute in February, 1879, Mr. Eckley B. Coxe, then president of the Institute, called attention in his address to the subject of Secondary Technical Education, and

Jan 1, 1881

By R. E. Lund, D. E. Warnes

SELECTIVE sulfation of individual constituents in ores or metalliferous products has received increased attention in recent years. The fluid-bed reactor with its advantages of close control of both temperature and atmosphere promises to have ap-

Jan 1, 1958

By W. H. Gauvin, N. J. Themelis

Jan 1, 1963

By W. D. Douglas, M. J. Hampshire, G. J. C. Young

This paper describes the replacement of a conventional filtration, clarification, and zinc precipitation plant by a carbon-in-pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers early laboratory studies to the design and erection of the full-scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies employed to solve them.

Jan 1, 1985