Search Documents

[ ]

Jan 1, 1938

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By M. Muskat, H. H. Evinger

A METHOD has been developed whereby one may calculate the productivity factors of producing formations from a knowledge of the reservoir conditions. Account is taken not only of the heterogeneous character of the gas-oil flow system but also of the detailed variations with pressure of the shrinkage and viscosity of the oil, the solubility of the gas in the oil, and even the variability of the gas viscosity and the deviation of the gas from ideal behavior. Curves are shown giving the results of numerical calculations on the production rate as a function of the pressure differential for a high-pressure and a low-pressure system, three values of gas-oil ratio being treated in each case. Curves are also given showing the variation with distance from the well of the pressure, oil saturation, and permeability. The effect of connate water is briefly discussed in relation to the apparently large discrepancies between the calculated and observed productivity-factor values. INTRODUCTION The significance of the productivity factor as a measure of the capacity of an oil-bearing formation to produce is well recognized; for it is the composite and integrated resultant of the physical properties of both the porous medium and the fluid stream passing through it with respect to the ease with which the particular petroleum fluids present in the formation can flow through it and into producing wells. The most direct method of determining the productivity factor of a well consists, as is well known, in the simultaneous measurement of reservoir-pressure differentials and rates of production and the expression of the data in terms of rate of flow per unit pressure drop.1 Actual measurements carried out in this manner on producing wells have given factors that generally lie in the range of 0 to 100 bbl. per day per pound pressure drop. This wide range arises not only from variations in permeability but also from the varying sand thickness of producing formations. One of the aims of developing a theory of the mechanics of oil production obviously is that of predicting what the productivity factor should be from a knowledge of the individual characteristics of the producing formation and the fluids produced. For homogeneous fluid systems passing through a porous medium into a producing well, it has been known for some time that the steady-state rate of liquid flow Q is given by the formula:* [ ] where k is the sand permeability, h its thickness, µ the liquid viscosity, [Ap] the pressure drop between the well and the distant parts of the reservoir, in particular that at a radius [ro ]and [r ] is the well radius. This gives the productivity factor: [ ] which will have a numerical value for a liquid of I centipoise viscosity of 0.9316 or

Jan 1, 1941

By F. R. Cattoir, R. W. Kimball, C. T. Anderson

ONE of the principal impurities in all steels is sulphur. Sulphur-bearing, manganese-free steels exhibit hot shortness. Manganese is added to steel to improve the hot-working properties. If no sulphur were present in steel, it is probable that hot shortness would be nonexistent. This paper is the first of a series to be issued by this Laboratory reporting the measurements of hot forgeability tests and the physical properties of Fe-C alloys to which additions of various alloying elements have been made. The present paper describes the results- obtained by the addition of varying amounts of sulphur to Fe-C alloys. To obtain control over residual elements in the various charges melted in the arc furnace, it was considered advantageous to use sponge iron from one source as the melting stock rather than scrap metal having an unknown history. Small amounts of unwanted alloying elements might be introduced into the charge when scrap was used, thereby influencing the results of the various heats. A sponge iron having a high silica-lime ratio was used. Ore from Sunrise, Wyo., had been reduced to sponge iron and briquetted at the Bureau of Mines sponge-iron plant at Laramie, Wyo. The briquettes were 5 in. in diam and 2 to 3 in. in thickness, and weighed about 10 lb each. The chemical analysis of the sponge iron is as follows: C, 0.67 pct; Mn, 0.10; SiO2, 4.75; CaO, 1.4; P, 0.044; S, 0.72; MgO, 0.4; A12O3, 1.1; total Fe, 87.5; Fe metallic, 79.2; and reduction, 90.5 pct. Where a reducing agent was required, crushed graphite electrodes usually were used. The charcoal available contained 0.20 pct S. An analysis of the available coke showed it to contain 0.70 pct S. Where high sulphur heats were required, elemental sulphur additions were made to the ladle. Limestone of good quality was obtained locally and had the following analysis: CaO, 53.7 pct; MgO, 0.8; ignition loss, 42.4; R2O3, 0.2; SiO2, 3.0; and P2O5, 0.014. Melting Procedure Sponge iron was melted to produce metal stock for the experimental alloys in a silica-lined, three-phase, direct-arc, size ST, Moore Rapid Lectromelt furnace with a 500 kva rating. Fig. 1 shows this furnace installation. About 25 tons of sponge iron was melted in 75 heats, averaging 927 lb of sponge iron to the heat. An addition of carbon was required to complete the reduction of a portion of the iron oxide remaining in the sponge to prevent high losses of iron oxide in the slag and a low carbon content in the resulting metal. As reducing agents in preparing the melting stock, charcoal, coke, and a carbon product resulting from the thermal decomposition of natural gas were used. The quantity varied from 20 to 60 Ib per furnace charge, with an average of 38 lb. An average analysis of the metal obtained gave 0.52 pct C, about 0.01 pct Mn, 0.070 pct P, and 0.092 pct S. The average yield of metal was 647 lb with 241 1b of slag, the sponge-iron recovery being 70 pct. The metal obtained in melting the sponge iron was cast into pigs weighing about 20 lb each to facilitate recharging into the furnace for further refining. The pouring of the pigs is shown in Fig. 2. The average power consumption for the production of the 24 tons of metal obtained was 1704 kw-hr per ton.

Jan 1, 1954

By J. G. Richardson, F. M. Perkins

Results and procedures are pre-cented covering a laboratory investigation of the effect of rate of water advance on the displacement of oil from clean water-wet sands. The experiments included water floods at atmospheric pressure with and without gas present over a range of flow rates from reservoir rates to rates ten thousand-fold higher. Water floods were also conducted at various rates at elevated pressure with no gas present. Other tests were made at elevated pressures by forming a free gas saturation by evolution of gas from solution in the oil before water flooding. Recovery of oil was found to be independent of the rate of water advance with or without gas present and independent of the pressure level of the water flood. A dimensionally-scaled model of a reservoir composed of a thick uniform sand was used to study the effect of rate on the tendency of water to underrun the oil because of the greater density of the water. Another model was used to study the effect of rate on the tendency of water to channel down the more permeable sand in a stratified reservoir composed of sands of diffierent per-meability in intimate contact. The effect of the presence of gas on the flooding conformance was studied with both models. The results obtained using these simple models provide a basis for predicting behavior in more complicated systems. INTRODUCTION In spite of the great amount of research on the flow of fluids in porous rocks, there still exists some disagreement as to the influence of the rate of water advance on the displacement of oil by water flooding. Various investigators have found that increasing the rate of water injection would decrease, increase, or have no effect on recovery of oil. One reason for this disagreement has been a lack of understanding of the effects of the capillary forces which influence the results obtained in the laboratory at low rates with short columns. Other causes of the disagreement have undoubtedly been inconstancy and uncertainty of the wetting properties of the porous media studied, inaccurate saturation determinations, and in some instances conclusions based on insufficient data. Capillary forces are involved in the displacement of oil by water in two ways. On the microscopic scale, the capillary forces control the dis- tribution of oil and water in the pore spaces of the sand. The magnitude of these forces is governed by the preference of the sand to be wet by water, the pore sizes and geometrical shapes, and the interfacial tension between the water and oil. On the macroscopic scale, differences in saturation at the flooding "front" when water displaces oil result in capillary pressure gradients. These gradients cause water to flow preferentially ahead of the front. In short laboratory columns at low rates, the front can span the entire column length. Also, at the outflow boundary the preference of sand to be wetted by water results in retention of water and a high water saturation in the region of the outflow face. This effect is commonly called the boundary effect.' The capillary pressure gradients which complicate the interpretation of flooding performance of short laboratory columns at low rates of water advance become negligibly small under certain conditions. The conditions where capillary pressure gradients are negligible are in long, homogeneous reservoir sands,' at high rates of water advance in short laboratory columns,3 and at any rate in laboratory columns as the residual oil saturation is approached. Thus, laboratory water floods, conducted

Jan 1, 1958

By H. J. Modi, P. L. De Bruyn

In recent years interest has been aroused in flotation rate studies both from a technical and a more practical aspect. With increasing fineness of grind becoming a necessity in treatment of low grade ores, differences in flotation rates of various size ranges will assume importance in the evaluation of overall recovery results. Theoretical analysis of flotation kinetics was initiated by Schuhmann, who sought to define flotation rate of a given mineral and specified size range in terms of certain physical variables of the flotation system. Using as a basis for his analysis the bubble- particle encounter hypothesis previously advanced by Gaudin, Schuhmann writes for the rate of flotation (R,) of particles of average size x, [ ]

Apr 1, 1956

By George M. Bouton, Lawrence Ferguson

The experiments described in this publication were inspired by the Bell System's large interest in lead-alloy sheathed cables and by the wide range of fatigue and corroding conditions to which they are sometimes subjected in service. The first experiments consisted of operating specimens of lead + I per cent antimony telephone cable sheath alloy in a fatigue test while they were immersed in water taken from a manhole. Because of many published reports concerning corrosion-fatigue phenomena of various metals and alloys, a reduction in fatigue life was expected(1)2 Instead, however, the fatigue test ran on for many times the normal number of cycles an4 was finally stopped without failure. Because of this, the experiments were broadened to include the effect of many media on the fatigue properties of four lead alloys over a wide range of testing speeds and strains. One material, a viscous tacky polymerized isobutylene3 used in

Jan 1, 1945

By Robert T. Hill

PHYSIOGRAPHICALLY, Mexico provinces, which are, in a manner, distinct economic areas. These may be denominated, (1) the Gulf coastal plain; (2) the Cordilleran plateau; (3) the Sonoran, and (4) the Tehuantepecan province. Fig. 1 shows the approximate boundaries of these provinces. The first is the continuation of the coastal plain of Texas and the Gulf region in general, which, except for prospective oil and lignite, has little of interest for the mining engineer.

Jan 1, 1902

By A. D. Rovig, D. W. McGlashan, Donald M. Podobnik

Crystal-chemical and stntctural properties of sulfide minerals are considered. The information gained is to be used to interpret (I ) freshly broken mineral surfaces, (2) modifications of the mineral surfaces, and (3) reactions at the mineral surfaces. From these basic disciplines, concepts with regard to the changes that surfaces undergo, reactions that might take place, the geometry of the interface, the state of different atoms and ions in the interface, and other physical and chemical properties of an interface must be developed, weighed and applied. The authors first deal with these conceptual considerations from which hypotheses are set forth to describe the environ men tal-interfacial relationships for several sulfide minerals. Qualitative and quantitative explanation of par-ticulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occurring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc., on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental-interfacial relationships for sulfide minerals. GENERAL CONSIDERATIONS Interfacial Reactions:Interfacial reactions are the cruxes of flotation schemes as well as other processes such as thickening, filtration and hydrometallurgy. However, as noted by Klassen and Mokrousov: 1 "The problems concerning the surfaces of natural minerals, the laws governing simultaneous adsorption from aqueous solution on these surfaces of a whole series of reagents, the laws of the surface reactions and the properties of water layers separating the minerals, are all known to a first approximation only." An investigator has the privilege of postulating methods of solid-liquid interfacial reactions. REACTIONS WITH WATER - Water consists of hydronium (H3 O 4) and hydroxyl (OH-) ions in the ionized state. That this is so forms the basis for the postulated reaction of the hydrated hydrogen ion with net-negative mineral surfaces as depicted in Fig. 1. In this case water is bonded to mineral surfaces through hydrogen-bridge-type bonds - possibly hydrogen bonds. Although bonding of the van der Waal type may be responsible for this reaction, it is most likely that stronger bonds are involved. Once firmly bonded to the surface, the water layer is known to be quite tenacious. It is further speculated that a shear plane exists at some distance (see Fig. 1) away from the mineral surface. Exact location of this plane is not known, but in all probability it will be positioned across a weak bond of the hydrogen-bond type where the surface-attached water is coordinated to the original hydrated hydrogen ion. REACTION WITH METAL IONS - Klassen and Mokrousov ' state: "The presence of an ion in water leads to an immediate formation around that ion of a highly condensed atmosphere of water dipoles and thus to hydration of the ion." The fact is known that multivalent cations are strongly hydrated, usually by six or eight molecules of water, and that anions are not so strongly hydrated. Conceding the fact that thermodynamics, concentration, pH, and physical considerations are of utmost importance in truly explaining a mechanism of metal ions reaction with a hydrated mineral surface, it does seem logical that the mechanism illustrated in Fig. 2 is feasible. In this reaction, the metal ion (M) is coordinated in one dimension - to the mineral-surface hydration layer. Note also that explanation of this reaction requires that the shear plane move to a less stable bond configuration; that is, the shear plane has moved to a position between the metal ion and the other coordinated water molecules which are more free to dissociate. Reactions as depicted in Fig. 2 should cause the formation of an apparent mineral surface which is net-positive. Immediately, it must be noted that measurements of apparent-mineral surfaces serve - within limits - to indicate a degree of ion-surface reaction capability. The major limiting factor he re is one related

Jan 1, 1970

By A. Szirmae, Hsun Hu

The early stages of recrystallization in a 70 pct cold-rolled Si-Fe crystal of the (110) (0011) orientation were studied with a Siemens electron microscope. Orientation studies based on electron-diffractzotz. patterns confirm the results of previous texture analysis. The driving energy for recrystallizatior and the critical radius for growth were calculated from the dislocation energy and the energy of the subgrain bourzdaries, and it was found consistent with the observed size of the recrystallized grains. The recrystallization characteristics of crystals with different initial orientations are discussed. The recrystallization of cold-rolled (110)[001] crystals of Si-Fe has been widely studied by various investigators.1-4 Their results on both deformation and annealing textures are in good agreement. The rolling texture after 70 pct reduction consists mainly of two crystallographically equivalent (111) [112] type textures and a minor component of the (100) [011] type. The latter is derived from the deformation twins, or Neumann bands, which are formed during the early stages of deformation and later rotate to the (100) [011] orientation upon further rolling reduction. Between the two main (111) [112] type textures, there is some orientation spread, because of which very low intensity areas appear in the pole figure. If these very low intensity areas are considered to be a very weak component in the texture, then a (110) [ 001 ] orientation may be assigned to them. When this rolled crystal is annealed at a sufficiently high temperature for recrystallization, the texture returns to a simple (110) [001]. The purpose of the present investigation was primarily to seek a better understanding of the recrystallization process by using the electron transmission technique. The (110) [0011 type of crystal was selected because orientation data for it are well known from previous studies with conventional techniques. Direct observations on the recrystallization of such a crystal have also been made by using a hot-stage inside the electron microscope, and the results will be reported in another paper. MATERIAL AND METHOD A single-crystal strip of the (110) [001] orientation was prepared from a commercial grade 3 pct Si-Fe alloy by the strain-anneal technique.= The strip was approximately 0.014 in. thick, and was rolled 70 pct at room temperature to a thickness of 0.004 in. Specimens were cut from the rolled strip and were annealed in a purified hydrogen or argon atmosphere. They were then electrolytically polished in a chromic-acetic acid solution to very thin foils. Best results were found by polishing first between two narrowly spaced flat cathodes with the specimen edges coated with acid-resisting paint, followed by polishing between two pointed electrodes until a hole appeared in the center as described by Bollmann.6 It was found that a thin transparent film always formed along the thin edges of the polished specimen. This film was then removed by rinsing the specimen very briefly in a solution of alcohol with a few drops of HF or HCl. RESULTS AND DISCUSSION 1) The Deformed Crystal. From the electron-diffraction patterns taken at various areas of an as-rolled specimen, the texture components as deduced - from ordinary pole-figure analysis were confirmed. Over most of the areas where orientation was examined, a (111) pattern with a [112] direction parallel to the rolling direction was obtained. This corresponds to the main deformation texture of the (111) [112] type. In a few areas the diffraction pattern was (100) [Oil], corresponding to the minor-texture component derived from the Neumann bands. The (110) [001] orientation, which corresponds to the very weak intensity area in the pole figure, was found infrequently. A typical example of the deformed matrix having the (111) type main texture is shown in Fig. 1, where (a) is the microstructure and (b) is the diffraction pattern taken from that area. It was also frequently observed that in other areas more or less continuous rings of weaker intensity were superimposed on the simple (111) diffraction pattern, suggesting the presence of a wide range of additional orientations. Other evidence indicated that the recrystallization characteristics are different in these two different types of areas. The hot-stage observations which provide this evidence will be discussed in another paper. AS shown in Fig. l(a), numerous dislocation-free areas of very small size are embedded in the "clouds" of high-dislocation density. This indicates that the deformation of a single crystal, even after a rolling reduction of 70 pct, is far from uniform on a micro-

Jan 1, 1962

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metal-lurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each, temperature from room temperature to fusion tempera-ture, and cooled at a rate that is not generally controllable but is pre-determined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each tem-perature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and dis-advantages of the extent of the zone are of prime moment, and are dis-cussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known.

Jan 1, 1935

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By P. G. Coombs

The kinetics of the cyclic oxidation and reduction processes for palladium powder were examined in the temperature range 848 to 923 K. The changes in oxidation behavior due to cycling are shown to result from the decrease in surface area. Sintering is found to occur only during the reduction process. Oxidation kinetics were found to follow a cubic law with time and yield a relation for the oxidation rate constant of k x = (1.05) 106 exp P74.0). 103 / RT] The kinetics of reduction are demonstrated to be first-order with the rate constant described by the expression: kr = (7.69) 1012 exp [-(208.0) 103 / RT] . In both expressions R is in J.mo1-1.K-1.

Jan 1, 1984

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By C. A. Stickels

A heat of electrolytic iron, to whzch alunzinutn and nitrogen had been added, was hot-rolled, cold-rolled 90 pct, and recrystallized at temperatures from 500" to 700°C. Primary recrystallization textures appear to arise from competitive growth of two types of nuclei: 1) those having orientations belonging to the "usual" primary recrystallization texture found in riming steel, and 2) those with the {111} (110) ovientation. Development of a (111}(1 10) component in the primary recrystallization texture occurs only over a certain interval of isothermal recrystallizatzon temperatures when the material is supersaturated with respect to the precipitation of AlN. Lowering the degree of supersaturation depresses the temperature interval in which a (111)(110) component occurs. An elongated, 'pancake-shaped" recrystallized pain structure and a marked delay in the start of recrystallization were found in all specimens which were supersaturated with respect to A1N precipitation after cold work, regardless of their recrystallization texture. ONE of the consequences of killing low-carbon steel with aluminum is a significant change in recrystallization behavior. About 15 years ago, Solter and eatttiel showed that this behavior was largely controlled by aluminum and nitrogen in the steel. If complete precipitation of A1N was prevented before cold rolling, an increased "recrystallization temperature" was observed in subsequent. annealing, and the recrystal-lized grains were not equiaxed. Leslie et a1.2 studied this phenomenon in some detail and clearly demonstrated the relationship between A1N precipitation, recrystallization kinetics, and the development of "pancake-shaped" grains. It has also been known for some time that aluminum-killed steels, processed to produce elongated "pancake" grains, develop a (11 I}( 110) primary recrystallization texture. This texture has not been found in iron or low-carbon rimming steel as a primary texture4j5 but has been observed following grain growth in electrolytic iron.5 The present work was undertaken to study in more detail the effect of A1N supersaturation on recrystallization textures in iron. LITERATURE REVIEW The deformation texture in heavily rolled iron has been studied in detail by Bennewitz.~ The texture consists primarily of a partial fiber texture about a (110) axis in the rolling direction, designated here as fiber texture A. It includes the range of orienta- tions (111)[110] - (001)[ 110] - (11l)[110]. A weak secondary texture also is present.6 This is a duplex partial fiber texture about two (110) fiber axes located 60 deg from the rolling direction and 30 deg from the sheet normal. The range of this texture, designated here as fiber texture B, about the [101} fiber axis is (112)[110] - near (545)[252] - (211:1[011] *The range given here follows Bennewit~.~ A few pole figures from re-crystallized material indicate a broader range than this.' However, the components which are strongest in the recrystallization texture are in this range.'________________________________________________________ Primary recrystallization textures in unkilled steels can be accounted for by growth of members of fiber texture B present in the deformed metal.5 However, while members of fiber texture B dominate the primary texture, other orientations survive primary recrystallization as well. In particular, some {111}(110) members of fiber texture A must also grow during primary recrystallization, because a well-defined {1ll)( 110) texture develops during subsequent grain growth at 700°C.5 The unusual recrystallization behavior of deformed supersaturated solid solutions has been attributed to: 1) retention of the solute in solution,' 2) formation of coherent, preprecipitation solute clusters prior to and during re~r~stallization,~ and 3) formation of a precipitate prior to and concurrent with recrystallization.'~-'~ When aluminum is supersaturated with iron, the difference in grain boundary mobility between general high-angle boundaries and certain special coincidence site boundaries is apparently eliminated.' In aluminum-killed steels, precipitation of A1N can take place at ordinary subcritical recrystallization temperatures. The rate of precipitation increases with increasing aluminum or nitrogen contents.2'13 There is some doubt, however, as to whether true precipitates form during the time at temperature needed to complete recrystallization. Leslie ef a1.2 found that precipitation in one steel was complete after about 100 min at 700GC, or after about 1000 min at 650GC, as measured by chemical analysis for AlN. Aoki et a1.,13 using internal friction for dissolved nitrogen, showed that a large fraction of the dissolved nitrogen was removed from solution within a few minutes annealing time at temperatures from 400" to 800°C. However , the rate of formation of AlN, as detected bv chemical analvsis. was much slower than the apparent rate of nitrogen removal. Hasebe,'~~ using carbon extraction replicas, has identified A1N precipitates by electron diffraction in a 0.2 C steel, solution-treated at 1300°C and annealed 2 hr at 700°C. Borchers and kim,I6 also using a replication technique, observed precipitates after annealing treatments as short as 2 min at 640°C. However, Leslie et a1.' state that no A1N precipitate can be seen while recrystallization is being inhibited in aluminum-killed steel.

Jan 1, 1967

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,' a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.'," Properties of Ferromagnetic Materials:'7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.' His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By D. W. Fuerstenau, P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the balls at different stages of pelletiz-ing are also discussed. In many industrial chemical processes, particulate matter can only be utilized if it is in an agglomerated form, such as pellets. Pelletizing is now widely used in iron ore technology1, and it has also been applied to a number of diverse fields such as the production of cement-kiln feed2, fertilizers3, and fluorspar4. Recently, it has been proposed to pelletize dispersion-type ceramic nuclear fuel elements5. In iron ore technology, for example, the production of agglomerates by pelletizing involves two major steps: 1) the preparation of green balls by rolling particles in a suitable balling device and 2) the firing of the green balls to form compact, strong bodies upon sintering. The critical step in a successful iron ore pelletizing operation is generally considered to be the balling operation1. In this paper, which is not concerned with the sintering of green pellets, the words green pelletizing and balling will be used interchangeably. Green pelletizing, or balling, will be defined as the process of forming larger bodies by rolling fine particles on a surface without the application of direct pressure. Two recent literature surveys6" indicate that in spite of the considerable amount of industrial pelletizing, very little is known about the fundamental principles of balling and its kinetics. The first reported research on the kinetics of pelletizing is the work of Newitt and Conway-Jones8. Using silica sands of different sizes in a batch laboratory balling drum, they found that the average green pellet diameter increased linearly with time at constant drum speed, and qualitatively the growth rate increased with moisture content. Generalized conclusions cannot be drawn from their research since the materials which they pelletized were sand and sand-silt mixtures rather than comminuted materials. Moreover, Newitt and Conway-Jones used testing sieves to estimate the size distribution of the green pellets, and this technique limited the range over which they could study the growth kinetics of the pellets. Bhrany and co-workers9 investigated the kinetics of balling iron ore fines on disk pelletizers ranging in diam from 1 to 18 ft. In their investigation, balling was carried out as a continuous operation, and growth kinetics were studied in terms of retention time of the material on the disk. Although the feed material in their study was quite coarse (the maximum size being about 1/2 in.), they also found qualitative relationships between pellet growth and water content, and feed size. In the present investigation, a number of innovations were introduced that refined the experimental measurements and established the reproducibility of balling experimentation. This enabled extension of the range of measurements to include study of agglomerate nucleation phenomena in the fractional mm size. This paper presents a detailed analysis of the nucleation and growth of green pellets in a laboratory balling drum. MATERIALS AND METHOD Pulverized limestone of specific gravity 2.72 was used as a model system in these studies. It has already been established that the balling characteristics of limestone and silica are similar to those of iron ore concentrates 2,8,10, depending on physical, rather than chemical, properties of the particles. The size distribution of the limestone was determined by a wet-dry sieving technique in the sieve range and by a sedimentation balance in the sub-sieve range. Fig. 1 presents the size distribution of the limestone used in this research. This figure shows that the material is finer than 200p (65 mesh) and that 25% of it is finer than 12. The specific surface area of this powder, as measured by BET gas adsorption methods,

Jan 1, 1964

By Garland R. Dever, Preston McGrain, George W. Ellsworth

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. High calcium and high carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental control measures, and other special uses are present in the High Bridge Group (Ordovician) and Warsaw and Ste. Genevieve Limestones (Mississippian). Deposits with thicknesses of 7.3 to 20.7 m,(24 to 68 feet) have been documented by the analysis of samples taken at 0.3-m (1ft) intervals. Active and potential mine and quarry sites afford access to water transporation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1979